2001 TOYOTA AVALON light

AX03T-04
D07231
Shift Lock Control Switch
Key Interlock Solenoid
Stop Light Switch Shift Lock Solenoid
Shift Lock Control ECU
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Column Shift)
AX-17
1307 Author
: Date
:
2001 AVALON (RM808U)
SHIFT LOCK SYSTEM (Column Shift)
LOCATION

AX0CS-02
D07232
Key Interlock Solenoid
Stop Light Switch
Shift Lock Control
Unit Assembly
- AUTOMATIC TRANSAXLESHIFT LOCK SYSTEM (Floor Shift)
AX-15
1305 Author
: Date
:
2001 AVALON (RM808U)
SHIFT LOCK SYSTEM (Floor Shift)
LOCATION

Q09982
AX03R-05
D07234
Q00270
Q057310.8 - 1.5 mm (0.031-0.059 in.)200 mm
(7.87 in.)
Q00270
AX-12
- AUTOMATIC TRANSAXLETHROTTLE CABLE
1302 Author
: Date
:
2001 AVALON (RM808U)
THROTTLE CABLE
ON-VEHICLE REPAIR
1. REMOVE BATTERY
2. REMOVE CRUISE CONTROL ACTUATOR
(a) Remove the 3 bolts and cruise control actuator.
(b) Disconnect the connector.
3. DISCONNECT THROTTLE CABLE FROM ENGINE
Disconnect the cable from the throttle linkage.
4. REMOVE PARK/NEUTRAL POSITION SWITCH
(See page AX-4)
5. REMOVE VALVE BODY
(See page AX-6)
6. REMOVE THROTTLE CABLE
(a) Remove the bolt and retaining plate.
(b) Pull out the cable from the transaxle case.
7. INSTALL THROTTLE CABLE
If the throttle cable is new, do the following operations (a) - (b).
(a) Bend the cable so there is a radius of about 200 mm (7.87
in.).
(b) Pull the inner cable lightly until slight resistance is felt, and
hold it there.
(c) Stake the stopper, 0.8-1.5 mm (0.031-0.059 in.) from the
end of outer cable.
(d) Install a new O-ring to the throttle calbe.
(e) Make sure to push it in all the way.
(f) Install the retaining plate and bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
8. INSTALL VALVE BODY (See page AX-6)

I14591
Connector ºAºConnector ºBº Radio Receiver Side
Connector ºCº
- BODY ELECTRICALAUDIO SYSTEM
BE-163
1767 Author
: Date
:
2001 AVALON (RM808U)
2. INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Connect the connectors from the radio receiver assembly, and
inspect the connector on the wire harness side.
Tester connectionConditionSpecified condition
A1 - Ground
(FR+)Audio sounding5 - 7 V
A2 - Ground
(FL+)Audio sounding5 - 7 V
A3 - Ground
(ACC, +B)Ignition switch ACCBattery positive voltage
A4 - Ground
(BU +B)ConstantBattery positive voltage
A5 - Ground
(FR-)Audio sounding5 - 7 V
A6 - Ground
(FL-)Audio sounding5 - 7 V
A7 - Ground
(GND)ConstantContinuity
A8 - Ground
(ANT +B)Radio power switch ONBattery positive voltage
A10 - Ground
(ILL+)Headlight dimmer switch ONBattery positive voltage
B1 - Ground
(RR+)Audio sounding5 - 7 V
B2 - Ground
(RL+)Audio sounding5 - 7 V
B3 - Ground
(RR-)Audio sounding5 - 7 V
B4 - Ground
(RL-)Audio sounding5 - 7 V
C1 - Ground
(+B)ConstantBattery positive voltage
C2 - Ground
(ILL+)Hesdlight dimmer switch ONBattery positive voltage
C3 - Ground
(AMP+)Rasio switch ONBattery positive voltage
C7 - Ground
(MUTE)Audio sounding1V or below

27 Noise NOISE PRODUCED BY VIBRATION OR SHOCK WHILE DRIVING
No
Ye s Is speaker properly installed?
Noise is produced from static eletricity accumulating in the vehicle body. With vehicles stationary lightly tap each system.
Is noise produced?Install properly.
Each system faulty. Is speaker properly installed?
No
No Ye s
Ye s
28 Noise NOISE PRODUCED WHEN ENGINE STARTS
NoYe s Whistling noise which becomes high-pitched when
accelerator strongly depressed, disappears shortly
after engine stops.Generator noise.
A/C noise.
Fuel gauge noise.
Horn noise.
Ignition noise.
Turn signal noise.
Washer noise.
Engine coolant temp. gauge noise.
Wiper noise. Whining noise occurs when A/C is operating.
Scratching noise occurs during sudden acceleration, driving on rough
roads or when ignition switch is turned ON.
Clicking sound is heard when horn button is pressed, then
released. Whirring/grating sound is heard when pushed
continuously.
Murmuring sound stops when engine stops.
Tick-tack noise occurs in co-ordination with blinking
offlasher.
Noise occurs during window washer operation.
Scratching noise occurs while engine is running,
and continues a while even after engine stops.
Scraping noise in line with wiper beat.
Other type of noiseYe s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s
Ye s No
No
No
No
No
No
No
No
- BODY ELECTRICALAUDIO SYSTEM
BE-159
1763 Author
: Date
:
2001 AVALON (RM808U)

BE04P-05
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE-1
1605 Author
: Date
:
2001 AVALON (RM808U)
BODY ELECTRICAL SYSTEM
PRECAUTION
HINT:
Take care to observe the following precautions when performing inspections or removal and replacement
of body electrical related parts.
1. HEADLIGHT SYSTEM
Halogen bulbs have pressurized gas inside and require special handling. They can burst if scratched or
dropped. Hold a bulb only by its plastic or metal case. Don't touch the glass part of a bulb with bare hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The AVALON is equipped with an SRS (Supplemental Restraint System) such as the driver airbag and front
passenger airbag. Failure to carry out service operation in the correct sequence could cause the SRS to
unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing (including re-
moval or installation of parts, inspection or replacement), be sure to read the precautionary notices in the
RS section.
3. AUDIO SYSTEM

If the negative (-) terminal cable is disconnected from the battery, the preset AM, FM 1 and FM 2 sta-
tions stored in memory are erased, so make sure to note the stations and reset them after the negative
(-) terminal cable is reconnected to the battery.

If the negative (-) terminal cable is disconnected from the battery, the radio, tape player and CD player
will not operate as well as audio anti - theft system. Be sure to input the correct ID number so that the
radio, tape player and CD player can be operated again.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to precautions in the IN section.

BE0I5-03
I0502712
3 5
1
2 3
5
BE-34
- BODY ELECTRICALBACK-UP LIGHT SYSTEM
1638 Author
: Date
:
2001 AVALON (RM808U)
INSPECTION
INSPECT BACK-UP LIGHT RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 - 2Continuity
Apply B+ between
terminals 1 and 2.3 - 5Continuity
If continuity is not as specified, replace the relay.

BE0I4-04
I12528
Ignition Switch
Back-Up Light Relay
Back-Up Light
Driver Side Junction Block

ECU-ACC Fuse
- BODY ELECTRICALBACK-UP LIGHT SYSTEM
BE-33
1637 Author
: Date
:
2001 AVALON (RM808U)
BACK-UP LIGHT SYSTEM
LOCATION