Page 405 of 1897
H12128
:7 Clips
H03125H12122H12806
w/o Speaker:
w/ Speaker:
2 Clips
H07599
H12124
2 Clips BO-32
- BODYLUGGAGE COMPARTMENT DOOR AND HINGE
1817 Author: Date:
2001 AVALON (RM808U)
17. REMOVE ROOF SIDE INNER GARNISH
(a) Using a screwdriver, remove the roof side inner garnish.
HINT:
Tape the screwdriver tip before use.
(b) Employ the same manner described above to the other
side.
18. REMOVE HIGH-MOUNTED STOP LIGHT
Remove the high-mounted stop light as shown in the illustra-
tion, then disconnect the connector.
19. REMOVE PACKAGE TRAY TRIM
(a) Using a screwdriver, remove the 3 rear seat belt bezel.
HINT:
Tape the screwdriver tip before use.
(b) Remove the package tray trim as shown in the illustration.
20. REMOVE UPPER BACK SILENCER
21. REMOVE TORSION BAR
(a) Disconnect the torsion bars from the torsion bar clamp,
then remove the torsion bar clamp.
Page 407 of 1897
BO41E-01
H17368
Outside Rear View Mirror
7.8 (80, 69 in.´lbf)
MirrorWire Retainer
Lower Frame
Bracket Garnish
Gasket
Door Trim Upper Armrest Base
Panel with Power
Window SwitchInside Handle Bezel
Courtesy Light
N´m (kgf´cm, ft´lbf) : Specified torqueTAIWAN:
Mirror
7.8 (80, 69 in.´lbf)
Outside Rear
View Mirror
- BODYOUTSIDE REAR VIEW MIRROR
BO-25
1810 Author: Date:
2001 AVALON (RM808U)
OUTSIDE REAR VIEW MIRROR
COMPONENTS
Page 409 of 1897
BO41F-01
H04751
H12102
H12103
H12104Clip BO-26
- BODYOUTSIDE REAR VIEW MIRROR
1811 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE INSIDE HANDLE BEZEL
(a) Using a screwdriver, remove the cover.
HINT:
Tape the screwdriver tip before use.
(b) Remove the screw.
(c) Using a screwdriver, remove the inside handle bezel as
shown in the illustration.
HINT:
Tape the screwdriver tip before use.
2. REMOVE COURTESY LIGHT
3. REMOVE UPPER ARMREST BASE PANEL WITH
POWER WINDOW SWITCH
(a) Using a screwdriver, remove the upper armrest base pan-
el with power window switch.
HINT:
Tape the screwdriver tip before use.
(b) Disconnect the connector.
4. REMOVE DOOR TRIM
(a) Using a screwdriver, remove the 2 caps.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 6 screws and clip.
(c) Pull the trim upward to remove it.
5. REMOVE LOWER FRAME BRACKET GARNISH
Using a screwdriver, remove the lower frame bracket as shown
in the illustration.
HINT:
Tape the screwdriver tip before use.
6. REMOVE OUTSIDE REAR VIEW MIRROR
(a) Disconnect the connector.
(b) Remove the 3 nuts and outside rear view mirror.
Torque: 7.8 N´m (80 kgf´cm, 69 ft´lbf)
Page 412 of 1897
BO41E-01
H17368
Outside Rear View Mirror
7.8 (80, 69 in.´lbf)
MirrorWire Retainer
Lower Frame
Bracket Garnish
Gasket
Door Trim Upper Armrest Base
Panel with Power
Window SwitchInside Handle Bezel
Courtesy Light
N´m (kgf´cm, ft´lbf) : Specified torqueTAIWAN:
Mirror
7.8 (80, 69 in.´lbf)
Outside Rear
View Mirror
- BODYOUTSIDE REAR VIEW MIRROR
BO-25
1810 Author: Date:
2001 AVALON (RM808U)
OUTSIDE REAR VIEW MIRROR
COMPONENTS
Page 414 of 1897
BO41F-01
H04751
H12102
H12103
H12104Clip BO-26
- BODYOUTSIDE REAR VIEW MIRROR
1811 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE INSIDE HANDLE BEZEL
(a) Using a screwdriver, remove the cover.
HINT:
Tape the screwdriver tip before use.
(b) Remove the screw.
(c) Using a screwdriver, remove the inside handle bezel as
shown in the illustration.
HINT:
Tape the screwdriver tip before use.
2. REMOVE COURTESY LIGHT
3. REMOVE UPPER ARMREST BASE PANEL WITH
POWER WINDOW SWITCH
(a) Using a screwdriver, remove the upper armrest base pan-
el with power window switch.
HINT:
Tape the screwdriver tip before use.
(b) Disconnect the connector.
4. REMOVE DOOR TRIM
(a) Using a screwdriver, remove the 2 caps.
HINT:
Tape the screwdriver tip before use.
(b) Remove the 6 screws and clip.
(c) Pull the trim upward to remove it.
5. REMOVE LOWER FRAME BRACKET GARNISH
Using a screwdriver, remove the lower frame bracket as shown
in the illustration.
HINT:
Tape the screwdriver tip before use.
6. REMOVE OUTSIDE REAR VIEW MIRROR
(a) Disconnect the connector.
(b) Remove the 3 nuts and outside rear view mirror.
Torque: 7.8 N´m (80 kgf´cm, 69 ft´lbf)
Page 423 of 1897
BO2PC-01
H10545
Primer M
Primer M
A BO-52
- BODYROOF DRIP SIDE FINISH CENTER MOULDING
1837 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
1. CLEAN CONTACT SURFACE OF BODY
(a) Using a heat light, heat the moulding surface to 40 - 60
°C (104 - 140 °F).
NOTICE:
Do not heat the body excessively.
(b) Using a knife, cut away any rough areas on the body.
NOTICE:
Be careful not to damage the body.
(c) Wipe off stains with cleaner.
2. If reusing the moulding:
CLEAN MOULDING
(a) Using a heat light, heat the moulding surface to 20 - 30
°C (68 - 86 °F).
NOTICE:
Do not heat the moulding excessively.
(b) Using a knife, cut the remaining adhesive from the mould-
ing.
NOTICE:
Be careful not to damage the moulding.
(c) Wipe off stains with cleaner.
3. COAT CONTACT SURFACE OF BODY WITH PRIMER
ºMº
Using a brush, coat the contact surface on the body with Primer
M as shown in the illustration.
Front and rear end:
A: 60 mm (2.36 in.)
NOTICE:
Allow 3 minutes or more to dry the primer cared sur-
face.
Do not coat the adhesive.
Do not keep any of the opened Primer M for later use.
Page 425 of 1897
BO2PB-01
N18625
N18626
- BODYROOF DRIP SIDE FINISH CENTER MOULDING
BO-51
1836 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE ENDS OF MOULDING
(a) Apply protective tape to the outer surface as shown in the
illustration to keep the surface from being scratched.
(b) Using a heat light heat the moulding to 20 - 30 °C (68 -
86 °F).
NOTICE:
Do not heat the moulding excessively.
(c) Using a scraper, pull off the roof drip side finish moulding
from the front end and rear end.
HINT:
Tape the scraper tip before use.
2. REMOVE MOULDING AND ADHESIVE
(a) Pull off the moulding by cutting the adhesive with a knife
at the front and rear ends.
(b) Remove the moulding.
NOTICE:
Do not damage the body with the knife.
3. REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP
Page 444 of 1897
BO2PZ-01
H12201
Roof Headlining
Roof Side Inner Garnish
Front Seat Outer
Belt Floor Anchor
Front Door
Opening Trim Assist Grip
w/ Rear personal light:
Rear Personal Light
Roof
Console
Box
Map Light Lens
Assist Grip
Sun Visor
Holder
Front Pillar Garnish
Front Door Scuff
Inside Plate
Center Pillar GarnishLensRoom Light
RH Rear Seat Inner
with Center Belt
Rear Door
Opening Trim
Lower Center
Pillar GarnishInside Rear Door
Scuff Plate
Rear Seatback
LH Rear Seat Inner
with Center Belt
Rear Seat Cushion
w/ Sliding roof:
Roof HeadliningSliding Roof
Opening Trim
41 (420, 30)
Lap Belt Outer Anchor Cover
41 (420, 30)
18 (185, 13)
18 (185, 13)
41 (420, 30)
: Specified torqueN´m (kgf´cm, ft´lbf)Cover
Cover
BO-98
- BODYROOF HEADLINING
1883 Author: Date:
2001 AVALON (RM808U)
ROOF HEADLINING
COMPONENTS
