Page 1147 of 4770

Maintenance Log.
. SUVs & Tacoma
SCHEDULED MAINTENANCE LOGS55
120,000 Miles or 96 Months
❑Replace engine air filter❑Replace engine coolant❑Replace engine oil and oil filter❑Rotate tires❑Replace limited-slip differential oil (Land Cruiser, RAV4 4WD)1
❑Replace platinum spark plugs (RAV4)2
❑Replace non-platinum spark plugs (Tacoma, 4Runner)2
❑Repack front wheel bearings (Tacoma 2WD)❑Lubricate propeller shaft and re-torque bolts (all 4WD except RAV4)❑Lubricate drive shaft bushings (4WD Tacoma without ADD)❑Re-torque drive shaft flange bolts (all 4WD except Land Cruiser)❑Inspect the following:__
Ball joints and dust covers__
Engine valves
__
Brake lines and hoses__
Exhaust pipes and mountings
__
Brake linings/drums and brake pads/discs__
Fuel tank cap gasket
__
Charcoal canister
3__
Steering gear box
__
Differential oil__
Steering linkage
__
Drive belts__
Transfer case oil (4WD models)
__
Drive shaft boots__
Transmission fluid or oil
__
Fuel lines and connections, fuel tank band
and fuel tank vapor vent system hoses
Additional Maintenance Items for Special Operating Conditions:*❑Inspect nuts and bolts on body and chassis❑Replace differential oil❑Replace transfer case oil (4WD models)❑Replace transmission fluid or oil
Date: __________________
Mileage: _______________
120,000 Miles or 96 Months
120,000 Miles or 96 Months
120 Months
DEALER SERVICE VERIFICATION
120 Months
❑Inspect SRS Air Bag
Date: __________________
Mileage: _______________
DEALER SERVICE VERIFICATION
1If vehicle is equipped with limited-slip differential.2Required under the terms of the Emission Control Warranty.
3Inspect at 120,000 miles or 144 months, whichever comes first.
Required only for vehicles in California, Massachusetts and New York.
Page 1622 of 4770

INTRODUCTIONGLOSSARY OF SAE AND TOYOTA TERMS ±
IN±7
IACIdle Air ControlIdle Speed Control (ISC)
IATIntake Air TemperatureIntake or Inlet Air Temperature
ICMIgnition Control Module±
IFIIndirect Fuel InjectionIndirect Injection
IFSInertia Fuel±Shutoff±
ISCIdle Speed Control±
KSKnock SensorKnock Sensor
MAFMass Air FlowAir Flow Meter
MAPManifold Absolute PressureManifold Pressure
Intake Vacuum
MCMixture Control
Electric Bleed Air Control Valve (EBCV)
Mixture Control Valve (MCV)
Electric Air Control Valve (EACV)
MDPManifold Differential Pressure±
MFIMultiport Fuel InjectionElectronic Fuel Injection (EFI)
MILMalfunction Indicator LampCheck Engine Light
MSTManifold Surface Temperature±
MVZManifold Vacuum Zone±
NVRAMNon±Volatile Random Access Memory±
O2SOxygen SensorOxygen Sensor, O2 Sensor (O2S)
OBDOn±Board DiagnosticOn±Board Diagnostic (OBD)
OCOxidation Catalytic ConverterOxidation Catalyst Converter (OC), CCo
OPOpen LoopOpen Loop
PAIRPulsed Secondary Air InjectionAir Suction (AS)
PCMPowertrain Control Module±
PNPPark/Neutral Position±
PROMProgrammable Read Only Memory±
PSPPower Steering Pressure±
PTOXPeriodic Trap OxidizerDiesel Particulate Filter (DPF)
Diesel Particulate Trap (DPT)
RAMRandom Access MemoryRandom Access Memory (RAM)
RMRelay Module±
ROMRead Only MemoryRead Only Memory (ROM)
RPMEngine SpeedEngine Speed
SCSuperchargerSupercharger
SCBSupercharger Bypass±
SFISequential Multiport Fuel InjectionElectronic Fuel Injection (EFI), Sequential Injection
SPLSmoke Puff Limiter±
SRIService Reminder Indicator±
SRTSystem Readiness Test±
STScan Tool±
TBThrottle BodyThrottle Body
TBIThrottle Body Fuel InjectionSingle Point Injection
Central Fuel Injection (Ci)
TCTurbochargerTurbocharger
TCCTorque Converter ClutchTorque Converter
TCMTransmission Control ModuleTransmission ECU (Electronic Control Unit)
TPThrottle PositionThrottle Position
TRTransmission Range±
Page 1631 of 4770
AUTOMATIC TRANSAXLESERVICE SPECIFICATIONS ±
AX±16
Differential
Drive pinion preload (at starting) New bearing
Reused bearing
1.0 ± 1.6 N´m
10 ± 16 kgf´cm 8.7 ± 13.9 in.´lbf
0.5 ± 0.8 N´m
5 ± 8 kgf´cm 4.3 ± 6.9 in.´lbf
Total preload (at starting)
New bearing
Reused bearing
Add drive pinion preload
0.3 ± 0.4 N´m
2.9 ± 4.0 kgf´cm 2.5 ± 3.5 in.´lbf
0.1 ± 0.2 N´m
1.5 ± 2.0 kgf´cm 1.3 ± 1.7 in.´lbf
Pinion to side gear backlash0.05 ± 0.20 mm
0.0020 ± 0.0079 in.
Side gear thrust washer thickness
0.95 mm
0.0374 in.
1.00 mm
0.0394 in.
1.05 mm
0.0413 in.
1.10 mm
0.0433 in.
1.20 mm
0.0427 in.
Page 1633 of 4770
AUTOMATIC TRANSAXLESERVICE SPECIFICATIONS ±
AX±18
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Stator shaft x Oil pump body101007
Upper valve body x Lower valve body5.45548
Ring gear x Differential case9798571
Side bearing cap x Transaxle case7273053
Bearing retainer x Transaxle case1919514
Counter drive gear x Drive pinion1721,750127
Carrier cover x Transaxle case2525018
Parking lock pawl bracket7.47565 in.´lbf
Overdrive case x Transaxle case2526019
Oil pump x Transaxle case2222016
Valve body x Transaxle case101007
Manual valve body x Transaxle case101007
Detent spring x Valve body101007
Oil tube bracket x Transaxle case101007
Oil strainer x Valve body101007
Oil pan x Transaxle case4.95043 in.´lbf
Park/Neutral position switch6.97061 in.´lbf
Park/Neutral position switch adjusting bolt5.45548 in.´lbf
Union2727520
AT06Q±0C
Page 1635 of 4770
AUTOMATIC TRANSAXLEGENERAL DESCRIPTION ±
AX±2
General Specifications
Type of TransaxleA140E
Type of Engine5S±FE
Torque Converter Clutch Stall Torque Ratio2.0 : 1
Lock±up MechanismEquipped
Gear Ratio 1st Gear
2nd Gear
3rd Gear
O/D Gear
Reverse Gear2.810
1.549
1.000
0.706
2.296
Number of Discs and Plates O/D Direct Clutch (C0)
Forward Clutch (C
1)
Direct Clutch (C
2)
Second Brake (B
2)
First and Reverse Brake (B
3)
O/D Brake (B
0)
2/1
4/4
3/3
3/3
6/5
2/3
B1 Band Width mm (in.)25 mm (0.98 in.)
ATF TypeATF DEXRON ® @@@@@: [g 2]
Capacity liter (US qts, Imp. qts)
Transaxle
Differential
5.6 (5.9, 4.9)
1.6 (1.7, 1.4)
Page 1642 of 4770
AUTOMATIC TRANSAXLEPREPARATION ±
AX±9
(09351±32111)Side Bearing Race Replacer
(09351±32120)Overdrive Bearing Replacer
(09351±32130)Handle
(09351±32140)Oil Seal Replacer
(09351±32150)Oil Seal Replacer
(09351±32190)Measure Terminal
(09351±32200)No.3 Piston Spring Compressor
09502±10012Differential Side Bearing Puller
09564±32011Differential Preload Adaptor
09710±28020Front Suspension Bushing Tool
Set
(09710±08040)Bushing Replacer
09950±00020Bearing Remover
RECOMMENDED TOOL
09031±00030Pin Punch .
AX0ER±02
Page 1643 of 4770
AUTOMATIC TRANSAXLEPREPARATION ±
AX±10
EQUIPMENT
Feeler gauge
Vernier calipers
Dial indicator or dial indicator with magnetic base
Straight edge
Torque wrench
LUBRICANT
ItemLiters
US qts Imp qtsClacification
Automatic Transaxle Fluid
(w/o Differential Fluid) Dry Fill
Drain and Refill5.6
5.9 4.9
2.5
2.6 2.2
ATF DEXRON ® @@@@@: [g 2]
Differential Fluid1.6
1.7 1.4ATF DEXRON ® @@@@@: [g 2]
SSM (SPECIAL SERVICE MATERIALS)
08826±00090Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG)
08833±00070Adhesive 1324,
THREE BOND 1324 or equivalent
AX0ES±02
AX0ET±02
AX0EU±02
Page 1661 of 4770
AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±28
DISASSEMBLY OF DIFFERENTIAL
1. REMOVE CARRIER COVER
2. MEASURE TOTAL PRELOAD
Using a torque meter, measure the total preload, and note
the measurement value.
3. MEASURE BACKLASH OF SIDE GEAR
Measure each side gear backlash while holding one pin-
ion toward the case.
Standard backlash:
0.05 ± 0.20 mm (0.0020 ± 0.0079 in.)
4. REMOVE LH BEARING RETAINER
(a) Remove the 6 bolts.
(b) Tap the retainer with a plastic hammer to remove it.
(c) Remove the O±ring from the retainer.
5. REMOVE RH SIDE BEARING CAP
Remove the 2 bolts and the side bearing cap.
AX0EX±02