2000 TOYOTA CAMRY clock

AUTOMATIC TRANSAXLEOPERATION ±
AX±4
1. FUNCTION OF COMPONENTS
FUNCTIONOPERATION
O/D Direct Clutch (C0)Connects overdrive sun gear and overdrive carrier
O/D Brake (B0)Prevents overdrive sun gear from turning either clockwise or
counterclockwise
O/D One±way Clutch (F0)When transmission is being driven by engine, connects overdrive sun
gear and overdrive carrier.
Front Clutch (C1)Connects input shaft and intermediate shaft
Rear Clutch (C2)Connects input shaft and front and rear planetary sun gears
No.1 Brake (B1)Prevents front and rear planetary sun gears from turning either clockwise
or counterclockwise
No.2 Brake (B2)Prevents outer race of F1 from turning either clockwise or counterclockwise, thus
previnting front and rear planetary sun gears from turning counterclockwise
No.3 Brake (B3)Prevents front planetary carrier from turning either clockwise or counterclockwise
No.1 One±way Clutch (F1)When B2 is operating prevents front and rear planetary sun gears from turning
counterclockwise
No.2 One±way Clutch (F2)Prevents front planetary carrier from turning counterclockwise

AUTOMATIC TRANSAXLEFRONT PLANETARY GEAR ±
AX±49
FRONT PLANETARY GEAR
COMPONENTS
ONE±WAY CLUTCH AND SUN GEAR
DISASSEMBLY
1. CHECK OPERATION OF ONE±WAY CLUTCH
Hold the sun gear and turn the hub. The hub should turn
freely clockwise and should lock counterclockwise.
2. REMOVE SECOND BRAKE HUB AND ONE±WAY
CLUTCH FRONT SUN GEAR
While turning the hub clockwise, remove the one±way
clutch from the sun gear.
AX0FE±02
AX0FF±02

AUTOMATIC TRANSAXLEFRONT PLANETARY GEAR ±
AX±51
4. INSTALL ONE±WAY CLUTCH AND SECOND BRAKE
HUB ON SUN GEAR
While turning the hub clockwise, slide the one±way clutch
onto the sun gear.
5. RECHECK OPERATION OF ONE±WAY CLUTCH
PLANETARY RING GEAR INSPECTION
1. INSPECT RING GEAR FLANGE BUSHING
Using a dial indicator, measure the inside diameter of the
flange bushing.
Standard inside diameter:
19.025 ± 19.050 mm (0.7490 ± 0.7500 in.)
If the inside diameter is greater than the maximum, re-
place the flange.
2. REMOVE RING GEAR FLANGE
(a) Using a screwdriver, remove the snap ring.
(b) Remove the flange from the ring gear.
3. INSTALL RING GEAR FLANGE
(a) Position the flange into the ring gear.
(b) Using a screwdriver, install the snap ring.
AX0FH±02

AUTOMATIC TRANSAXLEREAR PLANETARY GEAR ±
AX±55
REAR PLANETARY GEAR
COMPONENTS
ONE±WAY CLUTCH DISASSEMBLY
1. CHECK OPERATION OF ONE±WAY CLUTCH
Hold the outer race and turn the hub. The hub should turn
freely counterclockwise and should lock clockwise.
2. SEPARATE ONE±WAY CLUTCH AND PLANETARY
GEAR
3. REMOVE THRUST WASHERS
Remove the 2 thrust washers from both sides of the plan-
etary gear.
AX0FP±02
AX0FQ±02

AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±66
COUNTER DRIVE GEAR DISASSEMBLY
1. CHECK OPERATION OF ONE±WAY CLUTCH
(a) While turning the overdrive gear clockwise, install the ov-
erdrive direct clutch into the one±way clutch.
(b) Hold the overdrive direct clutch and turn the intermediate
shaft. The shaft should turn freely clockwise and should
lock counterclockwise.
(c) Remove the overdrive direct clutch.
2. CHECK COUNTER DRIVE GEAR PRELOAD
(a) Hold the intermediate shaft in a vise with soft jaws.
(b) Using a tension gauge, measure the preload.
Preload (at starting):
9 ± 15 N (920 ± 1,530 gf, 2.0 ± 3.4 lbf)
HINT: Turn the counter drive gear right and left several
times before measuring the preload.
3. REMOVE RETAINING PLATE
(a) Remove the snap ring with a screwdriver.
(b) Remove the retaining plate.
4. REMOVE ONE±WAY CLUTCH AND OUTER RACE
AX0G2±02

AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±72
12. INSTALL OVERDRIVE ONE±WAY CLUTCH INTO HUB
Be sure that the one±way clutch is installed in the correct
direction.
13. INSTALL RETAINING PLATE
(a) Place the retaining plate into the hub.
(b) Install the snap ring with a screwdriver.
14. CHECK OPERATION OF ONE±WAY CLUTCH
(a) While turning the overdrive gear clockwise, install the ov-
erdrive direct clutch into the one±way clutch.
(b) Hold the overdrive direct clutch and turn the intermediate
shaft. The shafts should turn freely clockwise and should
lock counterclockwise.
(c) Remove the overdrive direct clutch.

AUTOMATIC TRANSAXLEOVERDRIVE UNIT ±
AX±75
(b) Install the discs and plates.
Install in order: P=Plate D=Disc
Flange ± D ± P ± P ± D ± P
HINT: There are 2 different thickness plates, as shown in
the illustration.
(c) Install the cushion plate facing the rounded end upward.
3. INSTALL PISTON RETURN SPRING
4. INSTALL SNAP RING INTO CASE
Be sure the end gap of the snap ring is not aligned with
one of the cutouts.
5. INSTALL OVERDRIVE GEAR ASSEMBLY ONTO
CASE
While turning the overdrive gear clockwise, install the ov-
erdrive gear assembly to the case.
If the overdrive gear assembly is properly installed to the
overdrive case, the clearance between them will be about
24 mm (0.94 in.).

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±103
7. INSTALL NEW SPACER
Always use new spacer.
Install the spacer with the small end first.
8. INSTALL COUNTER DRIVEN GEAR ONTO SHAFT
(a) Place a bar at the drive pinion side and position the outer
end of the bar against a vise or similar.
(b) Using SST, driven in gear onto the shaft until the nut can
be installed on the threads of the shaft.
NOTICE: Be careful not to cause an impact to the transaxle
case.
SST 09350±32014 (09351±32140)
9. ADJUST DRIVE PINION PRELOAD
(a) Coat the threads and surface of the nut with MP grease.
(b) Using SST to hold the gear, tighten the nut.
Torque: 172 N´m (1,750 kgf´cm, 127 ft´lbf)
SST 09330±00021, 09350±32014 (09351±32032)
(c) Turn the gear counterclockwise and clockwise several
times.
(d) Using a torque meter, measure the preload of the drive
pinion.
Preload (at starting):
New bearing
1.0 ± 1.6 N´m (10 ± 16 kgf´cm, 8.7 ± 13.9 in.´lbf)
Reused bearing
0.5 ± 0.8 N´m (5 ± 8 kgf´cm, 4.3 ± 6.9 in.´lbf)