2000 TOYOTA CAMRY belt

SEAT BELT EXTENDER: '99±'01 MODEL YEAR ± BO002-01 January 26, 2001
Page 4 of 7REAR SEAT ± EXTENDER APPLICATION
MODELTYPE'01'00'99
RAV4W/TOKAI RIKAR±5R±5*1R±5*1
RAV4W/QSS±Q±4*2Q±4*2
ECHO±R±5R±5±
COROLLATMMC PRODUCTIONQ±4Q±4Q±4COROLLANUMMI PRODUCTIONT±1T±1T±1
PRIUS±N±7±±
LIFTBACK & COUPEN±6N±6N±6
CELICACONVERTIBLE (RH)±±N±1
CONVERTIBLE (LH)±±N±5
CAMRYTMC PRODUCTIONQ±4Q±4Q±4CAMRYTMMK PRODUCTIONQ±4Q±4Q±4
CAMRY SOLARACOUPEQ±4Q±4Q±4CAMRY SOLARACONVERTIBLEQ±4Q±4±
AVALON±T±1T±1Q±2
SIENNA±Q±4Q±4Q±4
TACOMAXTRACABA±2A±2A±2
4RUNNER±R±5R±5R±5
LAND CRUISER±K±5K±5K±5
SEQUOIAREAR SEAT #1T±1±±SEQUOIAREAR SEAT #2Q±4±±
TUNDRAACCESS CABQ±4Q±4±
HIGHLANDER±R±5±±
*1This seat belt was supplied by TOKAI
RIKA. Make sure that the I/D mark on
the back side of the seat belt buckle
is the same as shown.
*2 This seat belt was supplied by QSS.
Make sure that the I/D mark on the
back side of the seat belt buckle is
the same as shown.
NOTE:
The seat belt extender must not be
used for the center rear seat belt. Rear Seat
Belt Extender
Applications

SEAT BELT EXTENDER: '99±'01 MODEL YEAR ± BO002-01 January 26, 2001
Page 6 of 7
Failure to follow the recommendations indicated below could result in reduced
effectiveness of the seat belt restraint system in case of vehicle collision, causing
personal injury.
The Seat Belt Extender must not be used:
a. By anyone other than for whom it was provided (name recorded on seat belt
extender).
b. In any vehicle and/or seat position other than the one for which it was provided.
c. When the Seat Belt Extender is provided for rear seat positions (with automatic
locking retractor), make sure the retractor is locked when in use.
If your seat belt cannot be fastened securely because it is not long enough, a
personalized Seat Belt Extender is available from your Toyota dealer free of charge.
Please contact your local Toyota dealer so that the dealer can order the proper required
length for the extender. Bring the heaviest coat you expect to wear for proper
measurement and selection of length. Additional ordering information is available at your
Toyota dealer.
CAUTION:
When using the Seat Belt Extender, observe the following. Failure to follow these
instructions could result in reduced effectiveness of the seat belt restraint system in
case of vehicle accident, increasing the chance of personal injury.
Never use the Seat Belt Extender if you can COMFORTABLY fasten the seat belt
without it.
The Seat Belt Extender must never be used with any child safety seats.
Remember that the extender provided for you may not be safe when used on a
different vehicle, or for another person or at a different seating position than the
one originally intended for.
To connect the extender to the seat
belt, insert the tab into the seat belt
buckle so that the ªPRESSº signs on
the buckle-release buttons of the
extender and the seat belt are both
facing outward as shown.
You will hear a click when the tab locks
into the buckle.
When releasing the seat belt, press on
the buckle-release button on the
extender, not
on the seat belt. This helps
prevent damage to the vehicle interior
and extender itself.
When not in use, remove the extender
and store in the vehicle for future use.
Owner
Instructions
Seat Belt ExtenderSeat Belt Release

Page 7 of 7
PLEASE COPY THIS ORIGINAL WORKSHEET FOR EACH EXTENDER NEEDED
CAUTIONS:
To minimize the chance and/or severity of injury in an accident, the Seat Belt Extender must only be used:
1 By the person for whom it was provided.
2 In the seat position for which it was provided.
The Seat Belt Extender must never be used with any child safety seats.
When the Seat Belt Extender is provided for rear seat positions (with automatic locking retractor),
make sure the retractor is locked when extender belt is in use.
DEALER
SEAT BELT EXTENDER APPLICATIONAPPLICANT
DEALER
CODEDEALER
NAMEAPPLICANT
NAME
ADDRESSADDRESS
CITY
&
STATEZIPCITY
&
STATEZIPPHONE
EMPLOYEE
NAMEMODEL
YEARBODY
TYPESEATING
POSITIONVEHICLE
IDENTIFICATION
NUMBER
DIRECTIONS FOR DETERMINING PROPER EXTENDER LENGTH
1. Place the seat in the position the applicant normally uses.
2. With the applicant in the seat, wearing the thickest coat expected to be worn, pull belt all the way out
and try to buckle belt.
If belt latches into buckle and feels comfortable against upper chest area, an extender is not needed.
If belt does not buckle, continue with Step 3.
If buckle latches but belt has no slack remaining, continue with Step 3.
3. Measure distance between applicant's navel and seat belt buckle (Dimension A) and enter on Worksheet.
4. With belt all the way out, measure distance between latch tip and buckle tip (Dimension B) and enter
on Worksheet.
NOTE: If belt latches but there is no slack enter zero as Dimension B.
5. Subtract Dimension B from Dimension A and record number in Check Number box on Worksheet.
6. Seat Belt Extender length is Dimension B rounded up to next extender length (without exceeding
Check Number).
NOTE: If extender length exceeds Check Number, an extender cannot
be provided to the customer.
Dimension A:
NAVEL TO BUCKLEDimension B:
LATCH TO BUCKLE
BuckleNavel
ABuckle
Latch
B
SEAT BELT EXTENDER CALCULATION
DIMENSION
A:DIMENSION
B:CHECK
NUMBER:
SEAT BELT EXTENDER AUTHORIZATION
The same Seat Belt Extender can be used for right and left seating applications. Each Seat Belt
Extender will have a label identifying the owner, VIN and seating position. Seat Belt Extenders are
available only in black.
Applicant's Signature:
Date:
(Actual user of seat belt extender)

Toyota Supports ASE CertificationPage 1 of 3
BO011±01
Title:
NEW SEAT BELT TONGUE PLATE
STOPPER SERVICE PARTS
Models:
All Applicable Models
Technical Service
BULLETIN
March 23, 2001

A new service part for the seat belt tongue plate stopper has been introduced.
Installation procedures are provided to supplement the Repair Manual.
MODELYEAR
Avalon1995 ± 2001
Camry1983 ± 2001
Corolla1980 ± 2001
Camry Solara1999 ± 2001
Sienna (Front Seat Belt Only)1998 ± 2001
RAV41997 ± 2001
4Runner1992 ± 2001
Land Cruiser1991 ± 2001
Tundra2000 ± 2001
Tacoma1997 ± 2000
ECHO2000 ± 2001
Celica1980 ± 2001
Prius2001
Tercel1981 ± 1999
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
N/A73219±02010Stopper, Tongue Plate (Black)*
N/A73219±02020Stopper, Tongue Plate (Gray)*
N/A73219±02030Stopper, Tongue Plate (Beige)*
* Use a stopper color that is closest to the seat belt webbing color.
OP CODEDESCRIPTIONTIMEOPNT1T2
BD0047Install Seat Belt Tongue Plate Stopper0.173219±020#06212
Applicable Warranty*:
This repair is covered under the Toyota Comprehensive Warranty. This warranty is
in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's
in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information

NEW SEAT BELT TONGUE PLATE STOPPER SERVICE PARTS ± BO011±01 March 23, 2001
Page 2 of 3
1. Preparation
A. Shift the Tongue Plate to the
upper portion of the Tongue Plate
Stopper, and temporarily hold it
with a clip or tape.
B. Remove any pieces of the original
Tongue Plate Stopper in the
webbing, with a pair of pliers.
CAUTION:
Damaged or weakened seat belts may
break in an accident and injure the
occupant. The seat belt assembly must
be replaced if:
The webbing is cut, frayed, worn, or
damaged.
It has been used in a severe impact.
Inspect the entire length of webbing
for damage and replace the assembly
if needed. Be careful not to damage
the webbing during repair.
2. Install the New Tongue Plate Stopper
A. Install a new Tongue Plate
Stopper in the hole of the
webbing.
NOTE:
Be aware of the installation direction
of the Tongue Plate Stopper as shown
in the illustration.
B. Pinch the Tongue Plate Stopper
into the webbing using an
adjustable wrench, and turn and
push the adjustment screw by
hand.
HINT:
Press the adjustment screw in order to
position the male and female parts of
the Tongue Plate Stopper parallel to
each other, as shown in illustration.
CAUTION:
DO NOT use pliers. They may damage
the webbing. Installation
Procedure
Tongue
PlateTape
Example of
Broken Tongue
Plate Stopper
Tongue Plate
Stopper
Webbing

NEW SEAT BELT TONGUE PLATE STOPPER SERVICE PARTS ± BO011±01 March 23, 2001
Page 3 of 3
C. When the adjustment screw for
the adjustable wrench can't be
turned by hand, tighten the
adjustment screw using a pair of
adjustable joint pliers until the
space between jaws of the
adjustable wrench is 4.5 ± 5.0 mm.
(See illustrations.)
D. Check to be sure that the male
pin of the Tongue Plate Stopper
has become deformed evenly in
the hole of the female part and is
firmly held to the belt webbing.
(See illustrations.)
4.5 ± 5.0 mm
Installation
Procedure
(Continued)
CORRECT
INCORRECT

Toyota Supports ASE CertificationPage 1 of 7
BO020±98
Title:
1999 TOYOTA SEAT BELT EXTENDERS
Models:
All '95 through '99 model years
Technical Service
BULLETIN
July 3, 1998

Toyota customers who find it necessary to
increase the length of their seat belts may
obtain Seat Belt Extenders at no cost
through their local Toyota dealer.
The extender is available in 6 inch, 9 inch,
12 inch, 15 inch and 18 inch lengths.
The extender is available only in black.
Owners are informed of the seat belt
extender availability through the Toyota
Owner 's Manual included in each vehicle.
The customer
(individual requiring the extender) must visit a Toyota dealership to have
the required measurements made and to complete the seat belt extender worksheet.
The worksheet will allow the proper fitting and selection of a seat belt extender for the
customer. The dealership personnel should then determine the applicable part number
and place a
Critical Order through the TDN Parts Network.
The dealership service department should complete the affixed Seat Belt Extender Label
and review the ªowner instruction sheetº with the customer. The dealership should give a
copy of the completed worksheet to the customer and keep the original in the customer's
file.
To assure utmost owner satisfaction, it is recommended that a dealership designate one
person to coordinate all activities related to the seat belt extender issue.
From past sales history, it is recommended that dealerships do not stock Seat belt
extenders due to low demand and the need for customer fitting.
This bulletin contains the following information:
Procedure and Flow Chart...................... Page 2
Application Chart and Notes.................. Page 3
Part Number Information........................ Page 5
Owner Instructions.................................. Page 6
Seat Belt Extender Worksheet............... Page 7
All Toyota models, 1995 through 1999 model years.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty ±±±±
BODY
Introduction
Extender Seat Belt
Affected
Vehicles
Warranty
Information

SEAT BELT EXTENDERS: '95 ± '99 ± BO020±98 July 3, 1998
Page 2 of 7
1. Owner requests a seat belt extender from dealer.
2. Dealer verifies the need for a seat belt extender and obtains a current copy of this
TSB and copies the worksheet.
3. Dealer measures the customer and completes the worksheet. Dealer determines the
correct part number and places a Critical Order for the part through the TDN Parts
Network.
4. Dealer receives seat belt extender and calls the customer in to check fit of the part.
5. If the seat belt extender fit is good, dealership personnel completes the customer
information label on the part, explains usage of the part, and gives the customer a
copy of the completed worksheet.
6. Dealer places a copy of the completed worksheet in the customer's records.
DEALER
MEASURE
CUSTOMER
&
COMPLETE
WORKSHEET
PLACE
CRITICAL
ORDER
THROUGH
TDNSHIP SEAT
BELT
EXTENDER
TO
DEALERTEST FIT
CUSTOMER
WITH PARTCOMPLETE
LABEL AND
ADVISE
OWNERRECEIVE
COPY OF
WORKSHEET
& USE
EXTENDER
FILE
WORKSHEET
IN
CUSTOMER
RECORDS
EXTENDER FLOW CHART
PARTS
SUPPLYDEALEROWNER
CAUTION
DriverPassenger
FrontRear
Procedure
Sample Seat
Belt Extender
Label