2000 TOYOTA CAMRY oil

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±110
(e) Install the overdrive unit with overdrive case to the trans-
axle case.
(f) Install and tighten the bolts.
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)
9. CHECK INTERMEDIATE SHAFT END PLAY
(a) Make sure that the intermediate shaft has thrust play.
Thrust play:
0.49 ± 1.51 mm (0.0193 ± 0.0594 in.)
If the thrust play is not within specification, check the
installation of intermediate shaft.
(b) Make sure that the intermediate shaft turns smoothly.
10. INSTALL FIRST AND REVERSE BRAKE IN CASE
(a) Install the inner flange facing the flat end toward the oil
pump side.
(b) Install the discs and plates.
Install in order: P=Plate D=Disc
D ± P ± D ± P ± D ± P ± D ± P ± D ± P ± D
(c) Install the outer flange, facing the flat end toward the pis-
ton side.
11. INSTALL SNAP RING
Be sure the end gap of the snap ring is not aligned with
one of the cutouts.
12. CHECK OPERATION OF FIRST AND REVERSE
BRAKE
Apply compressed air into the oil passage with the case
and be sure that the piston moves.

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±112
(c) Coat the thrust washer with petroleum jelly and install it
onto the planetary gear.
16. CHECK OPERATION OF NO.2 ONE±WAY CLUTCH
Turn the planetary carrier. The carrier should turn freely
clockwise and lock counterclockwise.
17. INSTALL SNAP RING
Be sure the end gap of the snap ring is not aligned with
one of cutouts.
18. INSTALL SECOND COAST BRAKE BAND GUIDE
Install the 2 band guides so that its tip touches the case.
19. INSTALL SECOND BRAKE INTO CASE
(a) Install the flange, facing the flat end toward the oil pump
side.
(b) Install the discs and plates.
Install in order: P=Plate D=Disc
Flange ± D ± P ± D ± P ± D ± P

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±113
20. INSTALL PISTON RETURN SPRING
Each spring end is installed onto the protrusion with the
case.
21. INSTALL SECOND BRAKE DRUM INTO CASE
Align the groove of the drum with the bolt and place it into
the case.
22. INSTALL SNAP RING
(a) Place the snap ring into the case so that the end gap is
installed into the groove.
(b) While compressing the piston return springs over the
drum with hammer handles, install the snap ring into the
groove.
(c) Be sure the end gap of the snap ring is not aligned with
one of the cutouts.
23. INSTALL SECOND BRAKE DRUM GASKET
Install a new gasket until it makes contact with the second
brake drum.
24. CHECK OPERATION OF SECOND BRAKE
Blow compressed air into the oil passage with the case,
and be sure that the piston moves.

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±115
(b) Coat the race and bearing with petroleum jelly, and install
them onto the planetary gear.
Bearing and race
mm (in.)
Outer DiameterInner Diameter
Bearing45.0 (1.772)30.0 (1.181)
Race45.0 (1.772)28.0 (1.102)
(c) Install the planetary gear onto the ring gear.
28. INSTALL FRONT PLANETARY GEAR ASSEMBLY
ONTO SUN GEAR
(a) If the planetary gear and other parts are installed correctly
into the case, the end of the bushing with the ring gear
flange will be flush with a shoulder of the intermediate
shaft or under.
(b) Coat the race with petroleum jelly and install it onto the tip
of ring gear flange.
Race:
Outer diameter
35.7 mm (1.406 in.)
Inner diameter
23.0 mm (0.906 in.)
29. INSTALL INTERMEDIATE SHAFT OIL SEAL RING

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±116
30. INSTALL SECOND COAST BRAKE BAND
(a) Place the band into the case.
(b) Install the pin through the oil pump mounting bolt hole.
31. INSTALL FORWARD CLUTCH AND DIRECT CLUTCH
(a) Coat the races and bearing with petroleum jelly, and
install them onto both sides of the clutch drum.
Bearing and race (Front side)
mm (in.)
Outer DiameterInner Diameter
Bearing42.0 (1.645)28.9 (1.138)
Race42.0 (1.654)27.1 (1.067)

AT2765:Bearing and race (Rear side)
mm (in.)
Outer DiameterInner Diameter
Bearing36.1 (1.421)22.2 (0.874)
Race37.9 (1.492)22.0 (0.866)
(b) Coat the clutch drum thrust washer with petroleum jelly
and install it with the oil groove facing upward onto the di-
rect clutch drum.
(c) Align the flukes of discs in the direct clutch.

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±117
(d) Mesh the hub with the flukes of the direct clutch while turn-
ing the clutch drum or forward clutch.
(e) If the flukes of the discs are meshed with the hub correctly,
the end of the bushing with the direct clutch drum will be
flush with the surface of the forward clutch.
(f) Place the direct clutch and forward clutch into the case.
(g) Rotate the forward clutch to mesh the front planetary ring
gear and discs.
(h) Check the distance between the A and B.
Distance:
Approx. 3 mm (0.118 in.)
32. INSTALL OIL PUMP INTO CASE
(a) Coat the race with petroleum jelly and install it onto stator
shaft.
(b) Coat a new O±ring with ATF and install it to oil pump.

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±118
(c) Place the oil pump through the input shaft, and align the
bolt holes of the pump body with the transaxle case.
(d) Hold the input shaft, and lightly press the oil pump body
to slide the oil seal rings on the stator shaft through the
direct clutch drum.
NOTICE: Do not push on the oil pump strongly or the oil
seal ring will stick to the direct clutch drum.
(e) Install tighten the 7 bolts.
Torque: 22 N´m (225 kgf´cm, 16 ft´lbf)

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±122
44. INSTALL MANUAL VALVE BODY AND DETENT
SPRING
HINT: Each bolt length (mm, in.) is indicated in the illustra-
tion.
(a) Align the manual valve with the pin on the manual shaft
lever.
(b) Lower the manual valve body into place.
(c) Hand tighten the 4 bolts first. Then, tighten them with a
torque wrench.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
(d) Place the detent spring on the manual valve body and
hand tighten the 2 bolts first.
Then, tighten them with a torque wrench.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
(e) Check that the manual valve lever is touching the center
of the detent spring tip roller.
45. INSTALL OIL TUBES
Using a plastic hammer, install the 4 tubes into the posi-
tions indicated in the illustration.
NOTICE: Be careful not to bend or damage the tubes.
46. INSTALL TUBE BRACKET
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
47. INSTALL OIL STRAINER
Each bolt length (mm, in.) is indicated in the figure.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)