2000 TOYOTA CAMRY headlight aiming

'99camry U
232
ÐHeadlights
1. Open the hood. Unplug the connec-
tor. Remove the rubber cover.
If the connector is tight, wiggle it.2. Release the bulb retaining spring
and remove the bulb. Install a new
bulb and the bulb retaining spring.
To install a bulb, align the tabs of the
bulb with the cutouts of the mounting
hole.3. Install the rubber cover with the
ºTOPº mark upward, and snuggle on
the boss. Insert the connector. Then
install the plastic cover.
Make sure the rubber cover fits snugly on
the connector and the headlight body.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.

BE0A7±02
N20156
For Adjustment
in Vertical Direction
For Adjustment in
Horizontal Direction BE±28
± BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
2248 Author: Date:
ADJUSTMENT
1. ADJUST HEADLIGHT AIMING
2. ADJUST SPIRAL CABLE
(See page SR±16)

BE20X±01
I21909
For Adjustment
in Vertical Direction
BE±28
± BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
2238 Author: Date:
2001 CAMRY (RM819U)
ADJUSTMENT
ADJUST HEADLIGHT AIM ONLY
(a) Place the vehicle in the following conditions.

The area around the headlight is not deformed.

The vehicle is parked on a level surface.

Tire inflation pressure is the specified value.

A driver is in the driver's seat and the vehicle is in a state ready for driving (with a tank full).

The vehicle has been bounced several times.
(b) Check the headlight aiming.
(1) Prepare a thick white paper.
(2) Stand the paper perpendicular to the ground at the position 9.84 ft away from the headlights.
(3) Ensure that the center line of the vehicle and the paper face forms a 90±degree angle as shown
in the illustration.
(4) Draw a horizontal line (H line) on the paper, showing where the headlights should strike.
(5) Draw a vertical line (V line) to where the center line of the vehicle is to be.
(6) Draw 2 vertical lines to where the the headlights should strike (V RH and V LH lines).
(7) Draw a horizontal line (by connecting the both low beam center marks) to where the headlights
should strike (H RH and H LH lines).
HINT:
The H RH and H LH line is 0.4° below the horizontal line (H line) of the light axis.
(8) Start the engine.

Toyota Supports ASE CertificationPage 1 of 1
BO007±99
Title:
TMMK CAMRY/SIENNA HEADLIGHT
ALIGNMENT
Models:
'97±'99 Camry, '98±'99 Sienna
Technical Service
BULLETIN
April 16, 1999

To enhance headlamp performance on dark roads, the headlamp alignment process has
been modified.
1997±1999 TMMK Camrys produced before the following VINs:
Camry (4±Cyl) 4T1BG2 * K * XU453367
Camry (V±6) 4T1BF2 * K * XU079094
Camry (4±Cyl) 4T1BG2 * K * XU877828
Camry (V±6) 4T1BF2 * K * XU930732
1998±1999 Siennas produced before the following VIN:
Sienna 4T3ZF13C * XU119213
Headlight Aiming Device.
Refer to the '98 Camry Repair Manual
page BE±27. Adjust the headlight
nominal line 1'' higher. State and Federal
standards apply.
NOTE:
Vehicle lighting will remain within the
tolerances of all applicable federal and
state regulations.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot applicable to warranty±±±±
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Affected
Vehicles
Required
Tools and
Material
Repair
Procedure
New Nominal
cutline 1'' up
Warranty
Information