2000 TOYOTA CAMRY Crankshaft pulley

4. TEMPORARILY INSTALL NO.1 IDLER PULLEY AND
TENSION SPRING
(a) Install the pulley with the bolt. Do not tighten the bolt
yet.
HINT: Use a bolt 42 mm (1.65 in.) in length.
(b) Install the tension spring.
(c) Pry the pulley toward the left as far as it will go and
tighten the bolt.
(d) Check that the idler pulley moves smoothly.
5. TEMPORARILY INSTALL TIMING BELT
NOTICE: The engine should be cold.
(a) Using the crankshaft pulley bolt, turn the crankshaft
and position the key groove of the crankshaft timing
pulley upward.
(b) Remove any oil or water on the crankshaft pulley, oil
pump pulley, water pump pulley, No. 1 idler pulley, No.
2 idler pulley and keep them clean.
(c) Install the timing belt on the crankshaft timing pulley,
oil pump pulley, No.1 idler pulley, water pump pulley
and No.2 idler pulley.
HINT (When re±using timing belt): Align the points
marked during removal, and install the belt with the
arrow pointing in the direction of engine revolution. 2. INSTALL CRANKSHAFT TIMING PULLEY
(a) Align the timing pulley set key with the key groove of
the pulley.
(b) Slide on the timing pulley, facing the flange side
inward.
3. INSTALL NO.2 IDLER PULLEY
(a) Install the pulley with the bolt.
Torque: 42 N±m (425 kgf±cm, 31 ft±lbf)
HINT: Use a bolt 35 mm (1.38 in.) in length.
(b) Check that the idler pulley moves smoothly.
± 5S±FE ENGINEENGINE MECHANICALEG1±34

9. INSTALL CAMSHAFT TIMING PULLEY
(a) Align the camshaft knock pin with the knock pin
groove of the pulley, and slide on the timing pulley.
(b) Using SST, install the plate washer and bolt.
SST 09249 ± 63010 and 09278 ± 54012
Torque: 37 N±m (380 kgf±cm, 27 ft±lbf)
HINT: Use a torque wrench with a fulcrum length of
340 cm (13.39 in.)8. INSTALL CRANKSHAFT PULLEY
(a) Align the pulley set key with the key groove of the
pulley, and slide on the pulley.
(b) Using SST, install the pulley bolt.
SST 09213±54015 (91651 ±60855)
09330±00021
Torque: 108 N±m (1,100 kgf±cm, 80 ft±lbf)
10. SET No.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley, and align its groove with
timing mark ª0º of the No.1 timing belt cover. 7. INSTALL NO.1 TIMING BELT COVER
(a) Install the gasket to the timing belt cover.
(b) Install the timing belt cover with the 4 bolts. 6. INSTALL TIMING BELT GUIDE
Install the guide, facing the cup side outward.
± 5S±FE ENGINEENGINE MECHANICALEG1±35

11. INSTALL TIMING BELT
HINT. (When re±using timing belt):
wCheck that the matchmark on the timing belt
matches the end of the No.1 timing belt cover.
If the matchmark does not align, shift the meshing of
the timing belt and crankshaft timing pulley until they
align. (See page EG1±29)
(a) Remove any oil or water on the camshaft timing
pulley, and keep it clean.
(b) Install the timing belt, and check the tension between
the crankshaft timing pulley and camshaft timing
pulley. (b) Using SST, turn the camshaft, and align the hole of
the camshaft timing pulley with the timing mark of the
bearing cap.
SST 09278±54012
wAlign the matchmarks of the timing belt and
camshaft timing pulley.
12. CHECK VALVE TIMING
(a) Loosen the No.1 idler pulley bolt 1/2 turn.
± 5S±FE ENGINEENGINE MECHANICALEG1±36

13. INSTALL NO.2 TIMING BELT COVER
(a) Install the 2 gaskets to the No. 1 and No.2 belt covers.
(b) install the belt cover with the 5 bolts.
(c) Align the 2 clamps of the engine wire with cover
mounting bolts. (d) w/ Green Tension Spring:
Slowly turn the crankshaft pulley 1 and 7/8 revolu±
tions, and align its groove with the mark at 45
BTDC
(for No.1 cylinder) of the No.1 timing belt cover.
NOTICE: Always turn the crankshaft clockwise.
(c) Check that each pulley aligns with the timing marks as
shown in the illustration..
If the timing marks do not align, remove the timing
belt and reinstall it. (b) Turn the crankshaft pulley 2 revolutions from TDC to
TDC.
NOTICE: Always turn the crankshaft clockwise.
(e) Torque the mounting bolt of the No.1 idler pulley.
Torque: 42 N±m (425 kgf±cm, 31 ft±lbf)
± 5S±FE ENGINEENGINE MECHANICALEG1±37

Backlash
Crankshaft x No. 1 balance shaft
Off±vehicle
On±vehicle
No. 1 balance shaft x No.2 balance shaft
at D mark
at E mark
at F mark
Spacer thickness
Engine moving control rod x No. 2 engine mounting bracketCamshaft timing pulley x Camshaft (For use with SST)
TORQUE SPECIFICATIONS
No. 2 engine mounting bracket x Cylinder blockBalance shaft housing bolt outer diameter
Engine moving control rod X Fender apronOil pump pulley x Oil pump drive 'shaft Cylinder head cover x Cylinder head
Cylinder head x Cylinder block (1 styCamshaft timing pulley x Camshaft No. 2 idler pulley x Cylinder block
No. 1 idler pulley x Cylinder heedCrankshaft pulley x Crankshaft Spark plug x Cylinder headEngine
balancerThrust clearance
Part tightened
± 5S±FE ENGINEENGINE MECHANICALEG1±143

PREPARATION
SST (SPECIAL SERVICE TOOLS)
(09627±30010) Steering Sector Shaft Bushing
Replacer09226±10010 Crankshaft Front & Rear Bearing
Replacer
(09631±00020) Handle09616±30011 Steering Worm Bearing Adjusting
Screw Wrench
RECOMMENDED TOOLS
Oil pump oil seal
Oil pump oil seal 09620±30010 Steering Gear Box Replacer Set
09090±04000 Engine Sling Device
09200±00010 Engine Adjust Kit09032±00100 Oil Pan Seat Cutter
09905±00013 Snap Ring Pliers09228±06500 Oil Filter wrench
Precision straight edge
EQUIPMENT
Oil pressure gaugeFor suspending engineCrankshaft front oil seal
Torque wrenchOil pump pulley
Oil pump
± 5S±FE ENGINELUBRICATION SYSTEMEG1±270

11. REMOVE CRANKSHAFT TIMING PULLEY
If the pulley cannot be removed by hand, use 2 screw±
drivers.
HINT: Position shop rags as shown to prevent
damage.
12. REMOVE OIL PUMP PULLEY
Using SST, remove the nut and pulley.
SST 09616 ± 30011 8. SUSPEND ENGINE WITH ENGINE SLING DEVICE
9. REMOVE TIMING BELT (See page EG1±26)
10. REMOVE NO.2 IDLER PULLEY
Remove the bolt and pulley.
13. REMOVE OIL PUMP
(a) Remove the 12 bolts.
± 5S±FE ENGINELUBRICATION SYSTEMEG1±278

OIL PUMP INSTALLATION
(See Components for Removal and Installation)
1. INSTALL OIL PUMP
Install a new gasket and the oil pump with the 12
bolts.
Torque: 9.3 N±m (95 kgf±cm, 82 in.±lbf)
HINT: Long bolts are indicated in the illustration.
Bolt length:
Long bolt
35 mm (1.38 in.)
Others
25 mm (0.98 in.)
3. INSTALL CRANKSHAFT TIMING PULLEY
(a) Align the timing pulley set key with the key groove of
the pulley.
(b) Slide on the timing pulley, facing the flange side
inward. 2. INSTALL OIL PUMP PULLEY
(a) Align the cutouts of the pulley and shaft, and slide on
the pulley.
(b) Using SST, install the nut.
SST 09616±30011
Torque: 28 N±m (290 kgf±cm, 21 ft±lbf)
± 5S±FE ENGINELUBRICATION SYSTEMEG1±283