2000 TOYOTA CAMRY heater

PP0BT±03
PP±12
± PREPARATIONENGINE MECHANICAL (1MZ±FE)
64 Author: Date:
EQUIPMENT
Abrasive compound
Caliper gauge
CO/HC meter
Connecting rod aligner
Cylinder gauge
Dial indicator
Dye penetrant
Engine tune±up tester
Groove cleaning tool
Heater
Magnetic finger
Micrometer
OBDII scan tool
Pin hole grinderPiston pin hole
Piston ring compressor
Piston ring expander
Plastigage
Precision straight edge
Ridge reamer
Soft brush
Spring testerValve spring
Steel squareValve spring
Thermometer
Torque wrench
Valve seat cutter
Vernier calipers
Wire brushValve

PP0K1±03
PP±26
± PREPARATIONCOOLING (5S±FE)
78 Author: Date:
EQUIPMENT
HeaterECT switch, Thermostat
Radiator cap tester
ThermometerECT switch, Thermostat
Torque wrench
Vernier calipers

PP0C2±02
PP±30
± PREPARATIONCOOLING (1MZ±FE)
82 Author: Date:
EQUIPMENT
HeaterECT switch
Radiator cap tester
ThermometerECT switch
Torque wrench

SS109±02
± SERVICE SPECIFICATIONSSFI (1MZ±FE)
SS±21
184 Author: Date:
SFI (1MZ±FE)
SERVICE DATA
Fuel pressure
regulatorFuel pressure at no vacuum301 ± 347 kPa (3.1 ± 3.5 kgf/cm2, 44 ± 50 psi)
Fuel pumpResistance at 20°C (68°F)0.2 ± 3.0 W
InjectorResistance
Injection volume
Difference between each cylinder
Fuel leakage13.4 - 14.2 W
60 ± 73 cm3 (3.4 ± 4.5 cu in.) per 15 sec.
13 cm3 (0.8 cu in.) or less
1 drop or less per 12 minute
MAF meterResistance (THA ± E2) at ±20°C (±4°F)
at 20°C (68°F)
at 60°C (140°F)14.6 ± 17.8 kW
2.21 ± 2.69 kW
0.29 ± 0.35 kW
Throttle bodyThrottle opener setting speed900 ± 1,950 rpm
Throttle
position
sensorResistance
Throttle valve fully closed VTA ± E2
Throttle valve fully open VTA ± E2
± VC ± E2
0.2 ± 6.3 kW
2.0 ± 10.2 kW
2.5 ± 5.9 kW
IAC valveResistance (+B ± RSO or RSC) at cold
at hot17.0 ± 25.0 W
21.5 ± 29.5 W
VSV for EGRResistance at 20°C (68°F)27 ± 33 W
VSV for EVAPResistance at 20°C (68°F)27 ± 33 W
VSV for ACISResistance at 20°C (68°F)33 ± 39 W
VSV for Vapor
Pressure SensorResistance at 20°C (68°F)33 ± 39 W
Vapor
Pressure
SensorPower source voltage4.5 ± 5.5 V
ECT sensorResistance at ±20°C (±4°F)
at 0°C (32°F)
at 20°C (68°F)
at 40°C (104°F)
at 60°C (140°F)
at 80°C (176°F)10 ± 20 kW
4 ± 7 kW
2 ± 3 kW
0.9 ± 1.3 kW
0.4 ± 0.7 kW
0.2 ± 0.4 kW
EGR gas
temperature
sensorResistance at 50°C (122°F)
at 100°C (212°F)
at 150°C (302°F)64 ± 97 kW
11 ± 16 kW
2 ± 4 kW
A/F sensorHeater coil resistance at 20°C (68°F)
at 800°C (1472°F)0.8 ± 1.4 W
1.8 ± 3.2 W
Heated
oxygen sensorHeater coil resistance at 20°C (68°F)
at 800°C (1472°F)11 ± 16 W
23 ± 32 W
Fuel cut rpmFuel return rpm1,200 rpm

SF0EC±04
B06365
Ohmmeter
+B
HT
± SFI (5S±FE)AIR±FUEL RATIO (A/F) SENSOR (California)
SF±59
1492 Author: Date:
INSPECTION
1. INSPECT HEATER RESISTANCE OF A/F SENSOR
(a) Disconnect the A/F sensor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals +B and HT.
Resistance: 0.8 ± 1.4 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(c) Reconnect the A/F sensor connector.
2. INSPECT OPERATION OF A/F SENSOR
(See page DI±152)

SF0EI±03
B06363
Ohmmeter
HT
+B
± SFI (5S±FE)HEATED OXYGEN SENSOR (Bank 1 Sensor 1/Except
Calif.)SF±61
1494 Author: Date:
INSPECTION
1. INSPECT HEATER RESISTANCE OF HEATED OXY-
GEN SENSOR
(a) Disconnect the oxygen sensor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals +B and HT.
Resistance: 11 ± 16 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(c) Reconnect the oxygen sensor connector.
2. INSPECT OPERATION OF HEATED OXYGEN SEN-
SOR (See page DI±66)

SF0EK±03
S05303
Ohmmeter
HT +B
± SFI (5S±FE)HEATED OXYGEN SENSOR (Bank 1 Sensor 2)
SF±63
1496 Author: Date:
INSPECTION
1. INSPECT HEATER RESISTANCE OF HEATED OXY-
GEN SENSOR
(a) Disconnect the oxygen sensor connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals +B and HT.
Resistance: 11 ± 16 W at 20°C (68°F)
If the resistance is not as specified, replace the sensor.
Torque: 44 N´m (450 kgf´cm, 32 ft´lbf)
(c) Reconnect the oxygen sensor connector.
2. INSPECT OPERATION OF HEATED OXYGEN SEN-
SOR (See page DI±75)

SF08K±03
B06390
VSV Connector for
EVAP
Ground Cable
PCV Hose
Air Intake Chamber
Assembly
ECT Sensor
Connector ECT Sender
Gauge ConnectorEGR Valve Position
Sensor Connector
IAC Valve
Connector
VSV Connector
for EGR
VSV Connector for ACIS
Engine Wire
Engine Coolant
Reservoir HoseAir Assist Hose
Water Bypass Hose No.2 EGR Pipe
Throttle Position
Sensor Connector
No.1 Engine
HangerBrake Booster
Vacuum Hose Air Intake Chamber Stay
Water OutletPS Pressure Tube

Gasket
19.5 (200, 14)
39 (400, 19)12 (120, 19)
15 (150, 11)

Gasket
43 (440, 32)
Ground Starp
DLC1

Gasket
15 (150, 11)
Grand Strap
Connector

Gasket
39 (400, 29)
V±Bank Cover
Accelerator Cable
Throttle Cable
Air Cleaner
Hose
Purge HoseEGR Gas Temperature
Sensor Connector
Vacuum
HoseWater Bypass Hose
Fuel Inlet Hose
Heater Hose
Intake Manifold Assembly
Injector Connector x 9
Knock Sensor
Connector
Upper Radiator
Hose
Engine
Wire
Band
High±Tension Cord
Set
Gasket
: Specified torque

Non±reusable partN´m (kgf´cm, ft´lbf)

Retainer
Knock Sensor
SF±66
± SFI (1MZ±FE)KNOCK SENSOR
1565 Author: Date:
KNOCK SENSOR
COMPONENTS