2000 SUZUKI SWIFT SF310 Service Workshop Manual

MAINTENANCE AND LUBRICATION 0B-3
Interval:
This interval should be
judged by
This table includes services as scheduled up to 90,000 km (54,000 miles)
mileage. Beyond 90,000 km (54,000 miles), carry out the same services at
the same intervals respectively.
This interval should be judged by
odometer reading or months,Km(
1,000)153045607590g
whichever comes first.Miles(
1,000)91827364554
Months122436486072
4. EMISSION CONTROL SYSTEM
4-1.PCV (Positive Crankcase Ventilation)
ValveVehicle
without
O2S
––I––I
Vehicle
with O2S–––––I
4-2.Fuel evaporative emission control system–––––I
5. BRAKE
5-1.Brake discs and padsIIIIII
Brake drums and shoes–I–I–I
5-2.Brake hoses and pipes–I–I–I
5-3.Brake fluid–R–R–R
5-4.Brake lever and cableInspect at first 15,000 km (9,000 miles) only.
6. CHASSIS AND BODY
6-1.Clutch pedal (for manual transmission)–I–I–I
6-2.Tires/wheel discsIIIIII
6-3.Propeller shaft (4WD) and drive shafts––I––I
6-4.Suspension system–I–I–I
6-5.Steering system–I–I–I
6-6.Power steering (if equipped)IIIIII
6-7.Manual transmission oilI–R––R
6-8.Automatic transmissionFluid level–I–I–I
Fluid changeReplace every 165,000 km (99,000 miles).
Fluid hose–––R––
6-9.Rear differential oil (4WD) (R: 1st 15,000 km only)R or I–I–I–
6-10. All latches, hinges and locks–I–I–I
NOTES:

“R”: Replace or change

“I”: Inspect and correct or replace if necessary

0B-4 MAINTENANCE AND LUBRICATION
MAINTENANCE RECOMMENDED UNDER SEVERE DRIVING CONDITIONS
If the vehicle is usually used under the conditions corresponding to any severe condition code given below, it is
recommended that applicable maintenance operation be performed at the particular interval as given in the chart
below.
Severe condition code
A –Repeated short trips F –Leaded fuel use
B –Driving on rough and/or muddy roads G –(For Diesel engine) Town use / Towing a trailer /
C –Driving on dusty roads Sustained high speed driving /
D –Driving in extremely cold weather and/or Hot climates above 30C (86F) /
salted roads Low quality lubricants or fuel
E –Repeated short trips in extremely cold weather H –Trailer towing (if admitted)
Severe
Condition Code
MaintenanceMaintenance
OperationMaintenance Interval
BCDITEM 1-1IEvery 15,000 km (9,000 miles)
or 12 months
– B C D – – – –Drive belt (V-rib belt)REvery 45,000 km (27,000 miles)
or 36 months
A – C D E F – HITEM 1-4
Engine oil and filterREvery 5,000 km (3,000 miles)
or 4 months
A B C – E F – HITEM 2-1
Spark plugsREvery 10,000 km (6,000 miles)
or 8 months
ITEM 3 1IEvery 2,500 km (1,500 miles)
– – C – – – – –ITEM 3-1
Air cleaner filter *1REvery 30,000 km (18,000 miles)
or 24 months
– B C D – – – HITEM 6-2
Wheel bearingsIEvery 15,000 km (9,000 miles)
or 12 months
– B – D E – – H
ITEM 6-3
Propeller shaft (4WD) and drive
shafts
I
Every 15,000 km (9,000 miles)
or 12 months
– B – – E – – H
ITEM 6-7 / 6-8
Manual transmission oil and
differential oil (4WD)
R
Every 30,000 km (18,000 miles)
or 24 months
– B – – E – – HITEM 6-9
Automatic transmission fluidREvery 30,000 km (18,000 miles)
or 24 months
NOTES:

“R”: Replace or change

“I”: Inspect and correct or replace if necessary

*1: Inspect or replace more frequently if necessary

Vehicle with A/C
Vehicle with A/C and power steering
Vehicle with power steering
1. A/C compressor pulley
2. Power steering pump pulley3. Tension pulley
4. Crankshaft pulley
MAINTENANCE AND LUBRICATION 0B-5
MAINTENANCE SERVICE
ENGINE
ITEM 1-1
Drive Belt Inspection and Replacement
WARNING:
Disconnect negative cable at battery before checking and
replacing belt.
A / C Compressor and/or Power Steering Pump Drive Belt
Inspection (If equipped)
1) Detach air cleaner assembly from vehicle body and shift its posi-
tion.
2) Inspect belt for wear, deterioration and tension.
Replace or adjust, if necessary.
A / C compressor and / or power steering pump drive belt
tension “a”:
7 – 9 mm (0.28 – 0.35 in.) deflection under 10 kg or 22 lb
pressure
A / C Compressor and / or Power Steering Pump Drive Belt
Replacement
1) Disconnect negative cable from battery.
2) Remove engine under cover of right side.
3) Loosen belt tension and replace belt with new one.
4) Adjust belt tension to specification referring to SECTION 1B or
SECTION 3B1.
5) Install engine under cover and connect negative cable to battery.
Water Pump Belt Inspection
1) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
Replace, if necessary.
2) Check pump belt for tension and adjust it as necessary.
Water pump belt tension “a”:
6 – 8 mm (0.24 – 0.32 in.) deflection under 10 kg or 22 lb
pressure

1. Thickness gauge IN
EX
0B-6 MAINTENANCE AND LUBRICATION
Water Pump Belt Replacement
Replace belt with a new one. Refer to SECTION 6B for replacement
procedure of pump belt.
NOTE:
When replacing belt with a new one, adjust belt tension to
5 – 7 mm (0.20 – 0.27 in.).
ITEM 1-2
Camshaft Timing Belt Replacement
Replace belt with new one. Refer to SECTION 6A or 6A1 for re-
placement procedure.
CAUTION:

Do not bend or twist timing belt.

Do not allow timing belt to come into contact with oil, wa-
ter, etc.
ITEM 1-3
Valve Lash Inspection (1.3 liter engine only)
1) Remove cylinder head cover.
2) Inspect intake and exhaust valve lash and adjust as necessary.
Refer to SECTION 6A1 for valve lash inspection and adjustment
procedure.
Valve
lash
(gap)
When cold
(Coolant temperature is
15 – 25C or 59 – 77F)When hot
(Coolant temperature is
60 – 68C or
140 – 154F)
(gap)
specifi-
cation
Intake0.13 – 0.17 mm
(0.005 – 0.007 in.)0.17 – 0.21 mm
(0.007 – 0.008 in.)
cation
Exhaust0.23 – 0.27 mm
(0.009 – 0.011 in.)0.28 – 0.32 mm
(0.011 – 0.013 in.)
Special Tool
(A): 09917-18211
Tightening Torque
(a): 12 N
.m (1.2 kg-m, 8.5 lb-ft)
3) Install cylinder head cover and tighten bolts to specification.

MAINTENANCE AND LUBRICATION 0B-7
Proper Engine Oil Viscosity Chart
1. Oil pan
2. Oil drain plug
1. Oil filter
ITEM 1-4
Engine Oil and Filter Change
WARNING:
New and used engine oil can be hazardous.
Be sure to read “WARNING” in General Precaution in SEC-
TION 0A and observe what in written there.
Use engine oil of SE, SF, SG, SH or SJ grade.
Select the appropriate oil viscosity according to the left chart.
Before draining engine oil, check engine for oil leakage. If any evi-
dence of leakage is found, make sure to correct defective part be-
fore proceeding to following work.
1) Drain engine oil by removing drain plug.
2) After draining oil, wipe drain plug clean. Reinstall drain plug, and
tighten it securely as specified below.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
3) Loosen oil filter by using oil filter wrench (Special tool).
Special Tool
(A): 09915-47330
4) Apply engine oil to new oil filter O-ring.
5) Screw new filter on oil filter stand by hand until filter O-ring con-
tacts mounting surface.
CAUTION:
To tighten oil filter properly, it is important to accurately
identify the position at which filter O-ring first contacts
mounting surface.
6) Tighten filter 3 / 4 turn from the point of contact with mounting sur-
face using an oil filter wrench.
Special Tool
(A): 09915-47330
Tightening Torque (Reference)
(a): 14 N
.m (1.4 kg-m, 10.5 lb-ft)

1. Full level mark (hole)
2. Low level mark (hole)
Oil pan capacity
Oil filter capacity
Others
Total1.0 L and 1.3 L Engine
About 3.1 liters
(6.5 / 5.5 US / lmp pt.)
About 0.2 liter
(0.4 / 0.3 US / lmp pt.)
About 0.3 liter
(0.6 / 0.5 US / lmp pt.)
About 3.6 liters
(7.5 / 6.3 US / lmp pt.)
0B-8 MAINTENANCE AND LUBRICATION
7) Replenish oil until oil level is brought to FULL level mark on dip-
stick (oil pan and oil filter capacity). Filler inlet is at the top of cyl-
inder head cover.
8) Start engine and run it for three minutes. Stop it and wait another
5 minutes before checking oil level. Add oil, as necessary, to
bring oil level to FULL level mark on dipstick.
Engine Oil Capacity
NOTE:
Engine oil capacity is specified as left table.
However, note that amount of oil required when actually
changing oil may somewhat differ from data in left table de-
pending on various conditions (temperature, viscosity, etc.).
9) Check oil filter and drain plug for oil leakage.
ITEM 1-5
Engine Coolant Change
WARNING:
To help avoid danger of being burned, do not remove radia-
tor cap while engine and radiator are still hot. Scalding fluid
and steam can be blown out under pressure if cap is taken
off too soon.
CAUTION:
When changing engine coolant, use mixture of 50% water
and 50% ethylene-glycol base coolant (Anti-Freeze/Anti-
corrosion coolant) for the market where ambient tempera-
ture falls lower than –16C (3F) in winter and mixture of
70% water and 30% ethylene-glycol base coolant for the
market where ambient temperature doesn’t fall lower than
–16C (3F).
Even in a market where no freezing temperature is antici-
pated, mixture of 70% water and 30% ethylene-glycol base
coolant should be used for the purpose of corrosion protec-
tion and lubrication.
Refer to SECTION 6B for COOLANT CAPACITY.

For A / TFor M / T
MAINTENANCE AND LUBRICATION 0B-9
1) Remove radiator cap when engine is cool.
2) Loosen radiator drain plug (1) to drain coolant.
3) Remove reservoir and drain.
4) Tighten drain plug securely. Also install reservoir.
5) Slowly pour specified amount of coolant to the base of radiator
filler neck, and run engine, with radiator cap removed, until ra-
diator upper hose is hot. This drives out any air which may still
be trapped within cooling system. Add coolant as necessary un-
til coolant level reaches filler throat of radiator. Reinstall radiator
cap.
6) Add coolant to reservoir (1) so that its level aligns with Full mark
(2). Then, reinstall cap to reservoir aligning match marks (3) on
reservoir and cap.
ITEM 1-6
Exhaust System Inspection
WARNING:
To avoid danger of being burned, do not touch exhaust sys-
tem when it is still hot.
Any service on exhaust system should be performed when
it is cool.
When carrying out periodic maintenance or vehicle is raised for oth-
er service, check exhaust system as follows:

Check rubber mountings for damage and deterioration.

Check exhaust system for leakage, loose connections, dents,
and damages.
If bolts or nuts are loose, tighten them to specification. Refer to
SECTION 6K for torque specification of bolts and nuts.

Check nearby body areas for damaged, missing or mispositioned
parts, open seams, holes, loose connections or other defects
which could permit exhaust fumes to seep into vehicle.

Make sure that exhaust system components have enough clear-
ance from underbody to avoid overheating and possible damage
to floor carpet.

Any defects should be fixed at once.

0B-10 MAINTENANCE AND LUBRICATION
IGNITION SYSTEM
ITEM 2-1
Spark Plugs Replacement
Replace spark plugs with new ones referring to SECTION 6F or
6F1.
ITEM 2-2
Distributor Cap and Rotor Inspection (if equipped)

Check distributor cap and rubber caps for cracks.

Clean dusty and stained parts using a dry, soft cloth.

Check center electrode and terminals for wear.

Check rotor for cracks and its electrode for wear.
Repair or replace any component which is found to be in malcondi-
tion.
FUEL SYSTEM
ITEM 3-1
Air Cleaner Filter Inspection
1) Take out air cleaner filter as follows.
For 1.0 liter engine:
i) Remove air cleaner upper case after removing case nut and
clamps.
ii) Remove air cleaner filter.
For 1.3 liter engine:
i) Disconnect air cleaner outlet hose from case after loosening
its clamp and removing bolt (1) shown in figure.
ii) Remove air cleaner case cap (3) from case by unhooking its
clamps (2), then take out air cleaner filter.