2000 SUZUKI SWIFT Pulley

Vehicle with A/C
Vehicle with A/C and power steering
Vehicle with power steering
1. A/C compressor pulley
2. Power steering pump pulley3. Tension pulley
4. Crankshaft pulley
MAINTENANCE AND LUBRICATION 0B-5
MAINTENANCE SERVICE
ENGINE
ITEM 1-1
Drive Belt Inspection and Replacement
WARNING:
Disconnect negative cable at battery before checking and
replacing belt.
A / C Compressor and/or Power Steering Pump Drive Belt
Inspection (If equipped)
1) Detach air cleaner assembly from vehicle body and shift its posi-
tion.
2) Inspect belt for wear, deterioration and tension.
Replace or adjust, if necessary.
A / C compressor and / or power steering pump drive belt
tension “a”:
7 – 9 mm (0.28 – 0.35 in.) deflection under 10 kg or 22 lb
pressure
A / C Compressor and / or Power Steering Pump Drive Belt
Replacement
1) Disconnect negative cable from battery.
2) Remove engine under cover of right side.
3) Loosen belt tension and replace belt with new one.
4) Adjust belt tension to specification referring to SECTION 1B or
SECTION 3B1.
5) Install engine under cover and connect negative cable to battery.
Water Pump Belt Inspection
1) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
Replace, if necessary.
2) Check pump belt for tension and adjust it as necessary.
Water pump belt tension “a”:
6 – 8 mm (0.24 – 0.32 in.) deflection under 10 kg or 22 lb
pressure

1. No.1 cylinder
2. No.2 cylinder
3. No.3 cylinder
123
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-3
GENERAL INFORMATION
STATEMENT ON CLEANLINESS AND CARE
An automobile engine is a combination of many machined, honed,
polished and lapped surfaces with tolerances that are measured in
the thousands of an millimeter (ten thousands of an inch).
Accordingly, when any internal engine parts are serviced, care and
cleanliness are important.
Throughout this section, it should be understood that proper clean-
ing and protection of machined surfaces and friction areas is part
of the repair procedure. This is considered standard shop practice
even if not specifically stated.

A liberal coating of engine oil should be applied to friction areas
during assembly to protect and lubricate the surfaces on initial op-
eration.

Whenever valve train components, pistons, piston rings, con-
necting rods, rod bearings, and crankshaft journal bearings are
removed for service, they should be retained in order.
At the time of installation, they should be installed in the same
locations and with the same mating surfaces as when removed.

Battery cables should be disconnected before any major work is
performed on the engine.
Failure to disconnect cables may result in damage to wire har-
ness or other electrical parts.

Throughout this manual, the four cylinders of the engine are iden-
tified by numbers; No.1 (1), No.2 (2) and No.3 (3) counted from
crankshaft pulley side to flywheel side.
GENERAL INFORMATION ON ENGINE SERVICE
THE FOLLOWING INFORMATION ON ENGINE SERVICE
SHOULD BE NOTED CAREFULLY, AS IT IS IMPORTANT IN PRE-
VENTING DAMAGE, AND IN CONTRIBUTING TO RELIABLE EN-
GINE PERFORMANCE.

When raising or supporting engine for any reason, do not use a
jack under oil pan. Due to small clearance between oil pan and
oil pump strainer, jacking against oil pan may cause it to be bent
against strainer resulting in damaged oil pick-up unit.

It should be kept in mind, while working on engine, that 12-volt
electrical system is capable of violent and damaging short cir-
cuits.
When performing any work where electrical terminals can be
grounded, ground cable of the battery should be disconnected at
battery.

Any time the air cleaner, throttle body or intake manifold is re-
moved, the intake opening should be covered. This will protect
against accidental entrance of foreign material which could follow
intake passage into cylinder and cause extensive damage when
engine is started.

Oscilloscope Waveforms
Crankshaft
timing belt pulleyCKP
sensor
2V/Div.
5ms/Div.
Waveforms at specified idle speed
6-72 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0335 CRANKSHAFT POSITION (CKP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

No CKP sensor signal during 1 revolution of
camshaft.
CKP sensor circuit open or short.

Crankshaft timing belt pulley teeth damaged.

CKP sensor malfunction, foreign material being
attached or improper installation.

ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-3 (+) and C01-11 (–) of ECM (PCM) connector connected to ECM
(PCM) and check CKP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC, start engine and keep it at idle for 1 min.
2) Select “DTC” mode on scan tool and check DTC.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-73
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check CKP Sensor for Resistance.
1) Disconnect CKP sensor connector with ignition
switch OFF.
2) Then check for proper connection to CKP sensor
at “W/B” and “W/R” wire terminals.
3) If OK, measure sensor resistance between
terminals. See Fig. 1.
CKP sensor resistance: 360 – 460 Ω
at 20C, (68F)
4) Measure resistance between each terminal and
ground.
Insulation resistance: 1 MΩ or more.
Were measured resistance valves in step 3) and 4)
as specified?Go to Step 3.Replace CKP sensor.
3Check visually CKP sensor and pulley for the
following. See Fig. 2.

Damage

No foreign material attached.

Correct installation.
Are they in good condition?“W/B” or “W/R” wire
open or shorted to
ground, or poor
connection at C01-3
or C01-11.
If wire and connection
are OK, intermittent
trouble or faulty ECM
(PCM).
Recheck for
intermittent referring
to “Intermittent and
Poor Connection” in
Section 0A.Clean, repair or
replace.
Fig. 1 for Step 2 Fig. 2 for Step 3

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-3
GENERAL INFORMATION
STATEMENT ON CLEANLINESS AND CARE
An automobile engine is a combination of many machined, honed,
polished and lapped surfaces with tolerances that are measured in
the thousands of an millimeter (ten thousands of an inch).
Accordingly, when any internal engine parts are serviced, care and
cleanliness are important.
Throughout this section, it should be understood that proper clean-
ing and protection of machined surfaces and friction areas is part
of the repair procedure. This is considered standard shop practice
even if not specifically stated.

A liberal coating of engine oil should be applied to friction areas
during assembly to protect and lubricate the surfaces on initial op-
eration.

Whenever valve train components, pistons, piston rings, con-
necting rods, rod bearings, and crankshaft journal bearings are
removed for service, they should be retained in order.
At the time of installation, they should be installed in the same
locations and with the same mating surfaces as when removed.

Battery cables should be disconnected before any major work is
performed on the engine.
Failure to disconnect cables may result in damage to wire har-
ness or other electrical parts.

Throughout this manual, the four cylinders of the engine are iden-
tified by numbers; No.1 (1), No.2 (2), No.3 (3) and No.4 (4)
counted from crankshaft pulley side to flywheel side.
GENERAL INFORMATION ON ENGINE SERVICE
THE FOLLOWING INFORMATION ON ENGINE SERVICE
SHOULD BE NOTED CAREFULLY, AS IT IS IMPORTANT IN PRE-
VENTING DAMAGE, AND IN CONTRIBUTING TO RELIABLE EN-
GINE PERFORMANCE.

When raising or supporting engine for any reason, do not use a
jack under oil pan. Due to small clearance between oil pan and
oil pump strainer, jacking against oil pan may cause it to be bent
against strainer resulting in damaged oil pick-up unit.

It should be kept in mind, while working on engine, that 12-volt
electrical system is capable of violent and damaging short cir-
cuits.
When performing any work where electrical terminals can be
grounded, ground cable of the battery should be disconnected at
battery.

Any time the air cleaner, throttle body or intake manifold is re-
moved, the intake opening should be covered. This will protect
against accidental entrance of foreign material which could follow
intake passage into cylinder and cause extensive damage when
engine is started.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-73
Crankshaft
timing belt
pulleyCKP
sensor
Oscilloscope Waveforms
Waveforms at engine cranking (260 r/min) Waveforms at specified idle speed16 waives
for 10 signals13 waives for
10 signals
30 signal 30 signal 0.5 V / Div.
10 ms / Div.0.5 V / Div.
5 ms / Div.
DTC P0335 CRANKSHAFT POSITION (CKP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

NO CKP sensor signal for 2 seconds at engine
cranking.
CKP sensor circuit open or short.

Crankshaft timing belt pulley teeth damaged.

CKP sensor malfunction, foreign material being
attached or improper installation.

ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-23 (+) and C01-24 (–) of ECM (PCM) connector connected to ECM
(PCM) and check CKP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC and crank engine for 2 sec.
2) Select “DTC” mode on scan tool and check DTC.

6-1-74 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
INSPECTION
NOTE:
If starter circuit is open (i.e., start signal circuit is OK but starter fails to run), this DTC is stored in memory
at starter switch ON, even though CKP sensor is in good condition.
When starter motor fails to run and this DTC appears, check starter circuit first.
STEP
ACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Is there DTC P1500 (Engine starter signal circuit)?Go to DTC P1500
Diag. Flow Table.Go to Step 3.
3Check CKP Sensor for Resistance.
1) Disconnect CKP sensor connector with ignition
switch OFF.
2) Then check for proper connection to CKP sensor
at “W” and “B” wire terminals.
3) If OK, measure sensor resistance between
terminals. See Fig. 1.
CKP sensor resistance: 360 – 460 Ω at 20C,
68F
4) Measure resistance between each terminal and
ground.
Insulation resistance: 1 MΩ or more.
Were measured resistance valves in step 3) and 4)
as specified?Go to Step 4.Replace CKP sensor.
4Check visually CKP sensor and pulley for the
following. See Fig. 2.

Damage

No foreign material attached.

Correct installation.
Are they in good condition?“W” or “B” wire open or
shorted to ground, or
poor connection at
C01-23 or C01-24.
If wire and connection
are OK, intermittent
trouble or faulty ECM
(PCM).
Recheck for
intermittent referring
to “Intermittent and
Poor Connection” in
Section 0A.Clean, repair or
replace.
Fig. 1 for Step 3 Fig. 2 for Step 4

1. Timing belt
2. Tensioner
3. Tensioner plate
4. Tensioner spring
5. Spring damper
6. Camshaft timing pulley
7. Pin
8. Pulley bolt
9. Seal
10. Inside cover seal
11. Inside cover
12. Outside cover seal
13. Outside cover
14. Tensioner stud
15. Tensioner bolt
16. Tensioner spring screw
: Tightening Torque
6A-10 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
TIMING BELT AND BELT TENSIONER
REMOVAL
1) Disconnect negative cable at battery.
2) Hoist vehicle.
3) Remove clip (2) after pushing center pin, and then remove fend-
er apron extension (1) on right side.
NOTE:
Do not push center pin (3) too far in, or it will fall off into
fender.
4) Remove air cleaner assembly as previously outlined.
5) Remove A / C compressor drive belt, if equipped.
6) Loosen water pump pulley bolts (1).
7) Loosen generator pivot bolts (3) and its adjusting bolt (2) and re-
move water pump belt (4) and its pulley (5).