1999 TOYOTA CAMRY window

On some Toyota models, when Rapgard is removed from the vehicle, a stain is left on the paint
surface. This stain can be seen under the clear coat and is not a defect of the clear coat. The
stain corresponds to a wrinkled area of Rapgard which retained liquids, such as window washer
fluid, that left a discoloration.
REPAIR PROCEDURE:
To remove a stain from a vehicle, heat the stain surface to a temperature of 70C ± 80C.
When the stain is removed it will not reappear.
Equipment ±
1. Infrared lamp or dryer to heat the surface.
2. Aluminum foil or a damp cloth to protect plastic parts from deformation.
Procedure ±
1. Apply aluminum foil to adjoining plastic parts or cool with damp cloth periodically.
2. Use an infrared lamp or dryer on the stain developed area and heat for 5 to 10 minutes
at 70C ± 80C.
3. After heating for 5 minutes, check whether the stain has disappeared. If the stain still
remains, reheat the area and check again.
NOTE:Take care that the body's paint surface temperature does not become too high.
WARRANTY INFORMATION:
STAINS ON RAPGARD APPLIED AREASPage 1 of 1
AUGUST 9, 1996
BODY
BO008±96
ALL MODELS
OPCODE DESCRIPTION TIME OPN T1 T2
BD6004Remove stains from paint surface
caused by Rapguard0.653301±XXXXX 61 99
Stain

Toyota Supports ASE CertificationPage 1 of 2
BO012±99
Title:
DOOR GLASS DISPLACEMENT FIELD FIX
Models:
'98 ± '99 TMMK Camry
Technical Service
BULLETIN
September 3, 1999

On some 1998 and 1999 Camry Vehicles, the door glass may be displaced from the front
door glass run if the door is closed forcefully with the windows partially down. A field fix
has been developed in order to remedy this condition.
1998 ± 1999 TMMK Camrys built before 4T1BG * * K * XU553205
4T1BF * * K * XU084313
4T1BG * * K * XU903993
4T1BF * * K * XU932180
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
N/A67212±AA010Self±Adhesive Stopper
OP CODECOMBODESCRIPTIONTIMEOPNT1T2
670301AR&R Door Trim/Install Rubber Stopper
± Both Sides0.567402±AA0115357
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Parts
Information
Warranty
Information

DOOR GLASS DISPLACEMENT FIELD FIX ± BO012±99 September 3, 1999
Page 2 of 2
Refer to 1998 Camry Repair Manual (Vol. 2) Pages BO±11±14.
1. Remove the front door trim to gain access to the window components.
2. Inspect the front and rear lower frames and the door glass run for damage as a result
of the glass being displaced.
In cases of slight deformation of window frames, reform as necessary.
If significantly deformed or damaged, replace the frame.
Replace the window run if cut, torn, mutilated, etc.
3. Replace any damaged parts.
4. Remove front lower frame from the door and attach the self±adhesive rubber stopper
(P/N 67212±AA010) 120 mm from the top of the frame as shown below.
NOTE:
To insure proper adhesion of the self±adhesive rubber stopper, the surface of the
frame must be cleaned to remove any foreign material.
5. Reinstall the front lower frame, door glass run, and door trim.
Stopper
67212±AA010
(50 x 12 x 4.76 mm)
(double sided tape)
120 mm
Repair
Procedure

Toyota Supports ASE CertificationPage 1 of 2
BO017±99
Title:
DOOR GLASS DISPLACEMENT
Models:
'98 ± '99 TMMK Camry
Technical Service
BULLETIN
November 26, 1999

On some 1998 and 1999 Camry vehicles, the door glass may be displaced from the front
door glass run if the door is closed forcefully with the window partially down. A field fix
has been developed to remedy this condition.
1998 ± 1999 TMMK Camrys vehicles produced prior to VINs listed below.
MODELSTARTING VIN
1999 TMMK produced Camry
4T1BG**K*XU602813
4T1BF**K*XU088877
4T1BG**K*XU917744
4T1BF**K*XU933406
NOTE:
Refer to 1998 Camry Repair Manual (Vol. 2) BO±Section for Door Panel Removal and
Window Regulator Servicing information.
OP CODEDESCRIPTIONTIMEOPNT1T2
BD9008R&R Door Trim / Modify Hole (both sides)0.567402±AA0115357
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
BODY
Introduction
Applicable
Vehicles
Production
Change
Information
Warranty
Information

DOOR GLASS DISPLACEMENT ± BO017±99 November 26, 1999
Page 2 of 2
1. Lower the door glass, disconnect the power window switch, remove the front door
trim panel, speaker, and loosen the door mirror mounts to gain access to the door
glass and lower frames. Remove the front lower frame (2 screws).
2. Locate the lower window frame mounting hole on the door (see illlustration). Place a
towel or shop rag in the speaker hole to catch metal chips. Using a round file or die
grinder, enlarge the hole 2 mm toward the speaker (rear of the vehicle). Remove the
towel or shop rag and any metal chips in the door. Apply touch±up paint or rust
preventative to the hole.
2 mm"u
3. Install a rubber stopper to the lower window frame according to directions in TSB
BO012±99.
4. Install the lower window frame. Assure the frame is tight against the glass and the
run is fully inserted in the lower window frame channel.
5. Temporarily connect the power window switch and operate the window. Check to
assure the door glass fully opens and closes easily.
6. Reinstall the door panel and components, check lock/unlock function and door
opening handle function.
Repair
Procedure

SPEEDOMETER/TACHOMETER NEEDLE MOVEMENT ± EL003-02Revised: December 13, 2002 February 11, 2000
Page 2 of 2
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAME
83220 XXXXXSameSpeedometer83220-XXXXXSameTachometer
TOOLS & MATERIALSQUANTITY
Double Sided Cotton Swab1
Distilled Water1 oz.
1. Remove the combination meter
assembly per repair manual
instructions.
2. Remove the window plate from the
instrument cluster.
3. Clean the entire surface of the needle
and needle stopper as illustrated.
Using one end of a double sided
cotton swab, clean the contact point
between the pointer and the stopper
pin on the speedometer and
tachometer with distilled water.
Use only a new
, clean cotton
swab.
Use only distilled
water.
Use a new swab each time a part
is cleaned (one per speedometer,
one per tachometer).
NOTE:
After cleaning, do not touch the
pointer needle or stopper pin.
Do not blow dry the pointer or
stopper pin.
4. Use the opposite (dry) end of the
cotton swab to dry the previously
cleaned area.
5. Reassemble parts and assemble to
vehicle.
6. Confirm proper working condition of
speedometer and tachometer.
Confirm no foreign material
entered the cluster while the
window plate was removed.
Parts
Information
Required
Tools &
Material
Repair
Procedure

WARRANTY PARTS MARKING PROCEDURE ± PG006-03September 26, 2003
Page 3 of 3
NOTE:
The following parts do not have to be marked unless the technician can determine
failure and location.
air induction/ejection systems fuel injection systems
all computers fuel injectors
alternators fuel pump
audio (internal) ignition system
batteries internal engine components
bearings internal transmission components
belts oil cooler
catalytic converter power door lock switches
crankshaft remanufactured parts
cruise control starters
distributors suspension components
EGR systems valve covers
engine control systems window regulators
exchange parts wiper motors
exhaust systems
Parts
Marking
List
(Continued)

MIDTRONICS BATTERY TESTER SOFTWARE UPDATE ± SS002-02June 7, 2002
Page 3 of 10
1. Installing the Midtronics Update Wizard (MUW).
NOTE:
The Midtronics Update Wizard only needs to be installed once and must be installed
before the rest of the update process can take place. If this step is already complete,
continue on to step 2.
A. Click on the text ªInstall MUW.º (Figure 2.)
B. The file download window will appear. Click on ªRun this program from it's current
location.º
C. Click the ªOKº button.
D. Allow the Update Wizard to perform its self±installation. This will take only a few
minutes.
B
C
FIGURE 2.
A
Operation
Procedure