1999 TOYOTA CAMRY steering wheel

BO0MB±01
N20950
Instrument Panel ReinforcementNN
DD
No.2 Instrumental Panel Bracket
No.1 Instrumental Panel Bracket
No.2 Instrumental Panel Brace
QQH N
N
N
N
GG
NG
NOB
NN
Instrument Panel Brace Mount
No.1 Instrument
Panel BraceFront Pillar Garnish
Front Pillar
GarnishFront
Passenger
Airbag
Assembly
20 (200, 14)
No.2 Side Defroster Nozzle
Cowl Side Trim
Front Door Openin
g
Cover
Instrument Panel
C
Remote Control
Mirror Hole Base
Upper Column
CoverHazard Warning
Switch
Lower Finish
PlateGlove Compartment
Door Finish PlateFront Door
Inside Scuff Plate
FFF
FJ
Glove
Compartment
No.2 Lower
Panel A
A
Cluster Finish
Panel
Lower Column
Cover
Front Door
Opening
Cover
Cowl Side
TrimD
DD
D
D
F
AA
Lower Panel
InsertCoin
BoxCombination SwitchCombination
MeterRadio Assembly
Center Cluster
Finish Panel
A/C
Control Assembly
35 (360, 26)
Steering
Wheel
Pad Steering Wheel No.1 Lower
Panel
Front Door
Inside Scuff PlateFront Console
Box
Center Console
Upper PanelF
F
B
B
Rear Console
Box
N´m (kgf´cm, ft´lbf) : Specified torque BO±72
± BODYINSTRUMENT PANEL
2420 Author: Date:
INSTRUMENT PANEL
COMPONENTS

BO0MC±01
N20987
N21123
± BODYINSTRUMENT PANEL
BO±75
2423 Author: Date:
REMOVAL
1. REMOVE THESE PARTS:
HINT:
Tape a screwdriver tip before use.
(a) Front door inside scuff plates
(b) Cowl side trims
(c) Front pillar garnishes
(d) Front door opening covers
(e) Lower finish plate
2. REMOVE STEERING WHEEL
(See page SR±11)
3. REMOVE STEERING COLUMN COVERS
(a) Remove the steering tilt handle.
(b) Remove the 3 screws, then the upper and lower column
covers.
4. REMOVE COMBINATION SWITCH
5. REMOVE No.1 LOWER PANEL
(a) Remove the 2 screws and hood lock release lever.
(b) Press on the sides of the coin box while pulling the coin
box outward, and remove the coin box.
(c) Remove the screw, bolt and the No.1 lower panel.
6. REMOVE LOWER PANEL INSERT
(a) Remove the 2 screws holding the DLC3 to the LH lower
panel.
(b) Remove the 4 bolts, and the panel.
7. REMOVE No.2 LOWER COVER

± DIAGNOSTICSENGINE (5S±FE)
DI±15
250 Author: Date:
(b) TOYOTA Enhanced Signals.
TOYOTA hand±held tester displayMeasurement ItemNormal Condition*1
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.9 ~ 5.1 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio
Opening ratio rotary solenoid type IAC valveIdling: 25 ~ 62 %
STARTER SIGStarter SignalCranking: ON
CTP SIGClosed Throttle Position SignalThrottle fully closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SIGPark/Neutral Position Switch SignalP or N position: ON
ELECTCL LOAD SIGElectrical Load SignalDefogger S/W ON: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
PS OIL PRESS SWPower Steering Oil Pressure Switch SignalTurn steering wheel: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1, CYL#2, CYL#3, CYL#4Abnormal revolution variation for each cylinder0 %
IGNITIONTotal number of ignition for every 1,000 revolu-
tions0 ~ 2,000 rpm
EGR SYSTEMEGR system operating conditionIdling: OFF
FUEL PUMPFuel Pump SignalIdling: ON
A/C CUT SIGA/C Cut SignalA/C S/W OFF: ON
A/C MAG CLUTCHA/C Switch SignalA/C ON: ON
EVAP (PURGE) VSVEVAP VSV SignalVSV operating: Avove 30 %
VAPOR PRESS VSVVapor Pressure VSV SignalVSV operating: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 ~ 1.2 V
O2 LR B1, S1 *2
Heated Oxygen Sensor Lean Rich Bank 1 Sen-
sor 1: Response time for oxygen sensor output to
switch from lean to rich
Idling after warming up: 0 ~ 1,000 msec.
O2 RL B1, S1 *2
Heated Oxygen Sensor Rich Lean Bank 1 Sen-
sor 1: Response time for oxygen sensor output to
switch from rich to lean
Idling after warming up: 0 ~ 1,000 msec.
*1: If no conditions are specifically stated for ºldlingº, it means the shift lever is at N or P position, the A/C
switch is OFF and all accessory switches are OFF.
*2: Except California Specification vehicles.

DI±24
± DIAGNOSTICSENGINE (5S±FE)
259 Author: Date:
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
*1GBR
IdlingBelow 3.01
HTAF (E9 ± 2) ± E04 (E9 ± 15)G e BR
IG switch ON9 ~ 14
LOCK IN (E9 ± 18)
± E1 (E9 ± 14)W ± L e BRA/C compressor is operatingPulse generation
(See page DI±190)
LOCK (E7 15) E1(E9 14)RWBRA/C indicator light lights upBelow 4.0LOCK (E7 ± 15) ± E1(E9 ± 14)R ± W e BRA/C indicator light does not lights upBelow 1.0
A/C SW (E7 ± 10)RBBRA/C switch ON9 ~ 14A/C SW (E7 10)
± E1 (E9 ± 14)R ± B e BRA/C switch OFFBelow 1.0
PRS (E7 ± 13) ± E1 (E9 ± 14)G e BRA/C pressure is normallyBelow 1.0
THR (E8 10) E2 (E8 9)LRBRIG switch ON, A/C evaporator temp. 0°C (32°F)2.2 ~ 2.6THR (E8 ± 10) ± E2 (E8 ± 9)L ± R e BRIG switch ON, A/C evaporator temp. 15°C (59°F)1.4 ~ 1.8
MGC (E7 21) E01(E9 14)LYBRA/C magnetic clutch ONBelow 1.0MGC (E7 ± 21) ± E01(E9 ± 14)L ± Y e BRA/C magnetic clutch OFF9 ~ 14
* STP (E7 4) E1 (E9 14)GWBRIG switch ON, Brake pedal depressed7.5 ~ 14* STP (E7 ± 4) ± E1 (E9 ± 14)G ± W e BRIG switch ON, Brake pedal releasedBelow 1.5
ELS (E7 2) E1 (E9 14)BRBRDefogger switch and taillight switch ON7.5 ~ 14ELS (E7 ± 2) ± E1 (E9 ± 14)B ± R e BRDefogger switch and taillight switch OFFBelow 1.5
PSSW (E8 ± 12) BLBRIG switch ON9 ~ 14PSSW (E8 12)
± E1 (E9 ± 14)B ± L e BRAt idling, Turn steering wheel to lock positionBelow 3.0
SIL (E7 ± 16) ± E1 (E9 ± 14)W e BRDuring transmissionPulse generation
*: Only for A/T models
*1: Only for California Specification vehicles

± DIAGNOSTICSENGINE (5S±FE)
DI±27
262 Author: Date:
Symbols (Terminals No.)Wiring ColorConditionSTD Voltage (V)
*1GBR
IdlingBelow 3.01
HTAF (E9 ± 2) ± E04 (E9 ± 15)G e BR
IG switch ON9 ~ 14
LOCK IN (E9 ± 19)
± E1 (E9 ± 24)W ± L e BRA/C compressor is operatingPulse generation
(See page DI±190)
LOCK (E7 ± 20)RWBRA/C indicator light lights upBelow 4.0LOCK (E7 20)
± E1 (E9 ± 24)R ± W e BRA/C indicator light does not lights upBelow 1.0
A/C SW (E7 ± 10)RBBRA/C switch ON9 ~ 14A/C SW (E7 10)
± E1 (E9 ± 24)R ± B e BRA/C switch OFFBelow 1.0
PRS (E7 ± 19) ± E1 (E9 ± 24)G e BRA/C pressure is normallyBelow 1.0
THR (E8 11) E2 (E8 9)LRBRIG switch ON, A/C evaporator temp. 0°C (32°F)2.2 ~ 2.6THR (E8 ± 11) ± E2 (E8 ± 9)L ± R e BRIG switch ON, A/C evaporator temp. 15°C (59°F)1.4 ~ 1.8
MGC (E7 ± 21)LYBRA/C magnetic clutch ONBelow 1.0MGC (E7 21)
± E01 (E9 ± 13)L ± Y e BRA/C magnetic clutch OFF9 ~ 14
* STP (E7 9) E1 (E9 24)GWBRIG switch ON, Brake pedal depressed7.5 ~ 14* STP (E7 ± 9) ± E1 (E9 ± 24)G ± W e BRIG switch ON, Brake pedal releasedBelow 1.5
ELS (E7 13) E1 (E9 24)BRBRDefogger switch and taillight switch ON7.5 ~ 14ELS (E7 ± 13) ± E1 (E9 ± 24)B ± R e BRDefogger switch and taillight switch OFFBelow 1.5
PSSW (E9 ± 4) BLBRIG switch ON9 ~ 14PSSW (E9 4)
± E1 (E9 ± 24)B ± L e BRAt idling, Turn steering wheel to lock positionBelow 3.0
SIL (E7 ± 6) ± E1 (E9 ± 24)W e BRDuring transmissionPulse generation
TACH (E7 ± 7) ± E1 (E9 ± 24)B ± O eBRIdlingPulse generation
KSW (E10 4) E1 (E9 24)LBBRAt the time of inserting keyBelow 1.5KSW (E10 ± 4) ± E1 (E9 ± 24)L ± B e BRIn the condition without key insertedPulse generation
RXCK (E10 ± 3)
± E1 (E9 ± 24)R ± L eBRAt the time of inserting keyPulse generation
CODE (E10 ± 8)
± E1 (E9 ± 24)G ± W eBRAt the time of inserting keyPulse generation
TXCT (E10 ± 1)
± E1 (E9 ± 24)L ± Y eBRAt the time of inserting keyPulse generation
IMLD (E10 ± 1) ± E1 (E9 ± 24)R ± Y eBRIn the condition without key insertedPulse generation
MREL (E10 ± 7)
± E1 (E9 ± 24)B ± W eBRIG switch ON9 ~ 14
IGSW (E7 ± 1) ± E1 (E9 ± 24)B ± ReBRIG switch ON9 ~ 14
*: Only for A/T models
*1: Only for California Specification vehicles

± DIAGNOSTICSENGINE (1MZ±FE)
DI±209
444 Author: Date:
(b) TOYOTA Enhanced Signals.
TOYOTA hand±held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 1.6 ~ 2.9 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio
Opening ratio rotary solenoid type IAC valveIdling: 27 ~ 47 %
STARTER SIGStarter SignalCranking: ON
CTP SIGClosed Throttle Position SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N position: ON
ELCTRCL LOAD SIGElectrical Load SignalDefogger switch ON: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
PS OIL PRESS SWPower Steering Oil Pressure Switch SignalTurn steering wheel: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1 ~ CYL#6Abnormal revolution variation for each cylinder0%
IGNITIONTotal number of ignition for every 1,000 revolu-
tions0 ~ 3,000
EGRT GASEGR Gas Temperature Sensor Value
EGR not operating:
Temperature between intake air temp. and
engine coolant temp.
INTAKE CTRL VSVIntake Air Control Valve VSV SignalVSV operating: ON
EGR SYSTEMEGR system operating conditionIdling: OFF
A/C CUT SIGA/C Cut SignalA/C S/W OFF: ON
FUEL PUMPFuel Pump SignalIdling: ON
EVAP (PURGE) VSVEVAP VSV SignalVSV operating: Above 30%
VAPOR PRESS VSVVapor Pressure VSV SignalVSV operating: ON (TANK)
*: If no conditions are specifically stated for ºldlingº, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±629
864 Author: Date:
7. RELEASE METHOD OF AIRBAG ACTIVATION PRE-
VENTION MECHANISM
An airbag activation prevention mechanism is built into the con-
nector for the squib circuit of the SRS.
When release of the airbag activation prevention mechanism is
directed in the troubleshooting procedure, as shown in the il-
lustration of the connectors on the next pages, insert paper
which is the same thickness as the male terminal, between the
terminal and the short spring.
CAUTION:
Never release the airbag activation prevention mechanism
on the steering wheel pad connector.
NOTICE:

Do not release the airbag activation prevention mech-
anism unless specifically directed by the trouble-
shooting procedure.

If the inserted paper is too thick the terminal and short
spring may be damaged, so always use paper with
the same thickness as the male terminal.

H08316
TMC made :
Side Airbag Assembly (LH)
(Squib) Side Airbag Sensor (LH)Side Airbag Sensor (RH)Side Airbag Assembly (RH)
(Squib)
Seat Belt
Pretensioner (RH)
Airbag Sensor
AssemblyFront Passenger Airbag Assembly (Squib)
Spiral Cable
No.1 J/B 2
37 8
10
11
12
13
1
4
5
6
9
Steering Wheel
Pad (Squib) Front Airbag Sensor (RH)
Front Airbag Sensor (LH)
Seat Belt
Pretensioner (LH) 14
15
16
DI±630
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
865 Author: Date: