1999 LAND ROVER DISCOVERY Workshop Manual

ENGINE - V8
12-2-78 OVERHAUL
Reassembly
1.Clean camshaft bearings in block.
2.Clean camshaft.
3.Wipe camshaft bearing faces and lobes.
4.Clean thrust plate and mating face.
5.Lubricate camshaft bearings with clean engine
oil.
6.Fit camshaft, take care not to damage camshaft
bearings.
7.Lubricate thrust plate and mating face with
clean engine oil.
8.Position thrust plate, fit and tighten bolts to 22
Nm (17 lbf.ft).
9.Fit timing chain and gears.

+ ENGINE - V8, OVERHAUL, Timing
chain and gears.
10.Immerse tappets in engine oil. Before fitting,
pump the inner sleeve of tappet several times
using a push rod to prime the tappets.
11.Clean tappet bores.
12.Lubricate tappets and tappet bores with clean
engine oil.
13.Fit tappets.
14.Clean push rods.
15.Lubricate tappet end of push rods with clean
engine oil.
16.Fit push rods.
17.Clean bases of rocker pillars and mating faces.
18.Clean contact surfaces on rockers and valves.
19.Lubricate contact surfaces on rockers and
valves with clean engine oil.
20.Fit rocker shafts and engage push rods. Ensure
rockers shafts are fitted to the correct cylinder
head.
21.Fit and progressively tighten rocker shaft bolts
to 40 Nm (30 lbf.ft).
22.Fit inlet manifold gasket.

+ ENGINE - V8, OVERHAUL, Gasket -
inlet manifold.

EMISSION CONTROL - V8
DESCRIPTION AND OPERATION 17-2-1
EMISS ION CONTROL - V8 DESCRIPTION AND OPERAT ION
Crankcase emission control system
1Intake air
2LH rocker cover breather tube3Oil separator in RH rocker breather tube

EMISSION CONTROL - V8
17-2-2 DESCRIPTION AND OPERATION
Exhaust emission control
1RH catalytic converter
2Heated oxygen sensors – post-catalytic
converter (2 off – NAS only)3LH catalytic converter
4Heated oxygen sensors – pre-catalytic
converter (2 off)

EMISSION CONTROL - V8
DESCRIPTION AND OPERATION 17-2-3
Evaporative emission system
component layout
1Purge valve
2Service port
3Snorkel tube (UK / ROW only)
4CVS unit (NAS vehicles with vacuum type leak
detection only)
5EVAP canister breather tube
6Vent pipe – fuel tank to EVAP canister
7Relief valve regulated flow
8Relief valve (UK / ROW only)
9Relief valve free flow
10Fuel filler cap
11Liquid vapour separator #
(UK / ROW type shown)12Fuel filler hose (UK / ROW type shown)
13Tank breather hose (UK / ROW only)
14Vent hose
15Roll over valves (ROV's) –
(4 off, UK / ROW spec. shown)
16Fuel tank and breather assembly
17EVAP canister
18Purge line connection to engine manifold
19Tank EVAP system pressure sensor (NAS
vehicles with vacuum type leak detection only)
M17 0209
4
3
1
6
5
16
10
8
13
17
9
7
11
12
15
14
18
2
19

EMISSION CONTROL - V8
17-2-4 DESCRIPTION AND OPERATION
Evaporative emission system (with
positive pressure leak detection)
component layout (NAS only)
1Purge valve
2Service port
3Air filter canister
4EVAP canister breather tube
5Leak detection pump
6EVAP canister
7Vent pipe – fuel tank to EVAP canister
8Liquid vapour separator (metal)9Fuel filler cap
10Fuel filler
11Fuel tank breather assembly
12Vent hose
13Roll over valves (inside fuel tank)
14Fuel tank
15Purge line connection to engine manifold
M17 0208
3
1
7
4
14
11
6
8
10
13
12
15
2
5
9

EMISSION CONTROL - V8
DESCRIPTION AND OPERATION 17-2-5
Evaporative emission system control
diagram
1Battery
2Fuse 13 (engine compartment fusebox)
3Inertia switch
4Main relay (engine compartment fusebox)
5Engine Control Module (ECM)
6Purge Valve (black harness connector)
7Canister vent solenoid (CVS) valve – NAS
vehicles with vacuum type EVAP system leak
detection capability only8Leak detection pump – NAS vehicles with
positive pressure type EVAP system leak
detection capability only
9Fuel tank pressure sensor – NAS vehicles with
vacuum type EVAP system leak detection
capability only
10Instrument pack (MIL warning light)
M17 0210
12
3
4
5
6
7
9
8
10

EMISSION CONTROL - V8
17-2-6 DESCRIPTION AND OPERATION
Secondary air injection system
component layout
M17 0206
1234
56
8
7

EMISSION CONTROL - V8
DESCRIPTION AND OPERATION 17-2-7
1Engine Control Module (ECM)
2SAI vacuum solenoid valve
3Purge valve
4Vacuum reservoir (up to 2003 model year
location shown)
5SAI control valve (2 off)
6SAI pump
7SAI pump relay
8Main relay