1999 LAND ROVER DEFENDER Workshop Manual

12ENGINE
12
REPAIR
5.Progressively loosen then remove and discard 6
bolts; remove rocker shaft assembly.
6.Remove and discard lock nuts and rocker
adjusting screws.Refit
7.Clean rocker shaft and mating faces.
CAUTION: If rocker arms or shaft are to be
replaced, ensure replacements are correct.
Engine Serial No. Prefixes 10P to 14P are
fitted with Type A rocker arms and shaft. Engine
Serial No. Prefixes 15P to 19P are fitted with Type
B rocker arms and shaft. Type B rocker arms and
shaft may be fitted to Engine Serial No. Prefixes
10P to 14P as an assembly.
8.Fit new rocker adjusting screws into rocker arms.
Fit new lock nuts to screws but do not tighten.
CAUTION: Ensure screws are correct for
type of rocker arm fitted. Replacement
screws for Engine Serial No. Prefixes 15P
to 19P have a centre punch mark adjacent to the
adjusting slot. These screws are not
interchangeable with those fitted to Engine Sertial
No. Prefixes 10P to 14P.
9.Fit rocker shaft ensuring it is located on dowel.
10.Fit new retaining bolts and working from the
centre outwards, tighten bolts progressively to
32 Nm (24 lbf. ft).
ProCarManuals.com

ENGINE
13
REPAIR 11.Before refitting the camshaft cover, the fuel
injector rockers must be adjusted.
12.RemoveLRT-12-058.
13.Rotate engine clockwise until No. 1 injector lobe
is at full lift.
14.Rotate rocker adjusting screw clockwise until the
injector plunger is felt to bottom out.
15.Rotate rocker adjusting screw anti-clockwise 1
complete turn to give the plunger the required
bump clearance and tighten rocker adjusting
screw locknut to16 Nm (12 lbf.ft).
CAUTION: Ensure screw does not turn as
locknut is tightened.
16.Carry out above procedure for the remaining 4
rockers.
17.After completion of rocker adjustment, slowly
rotate engine clockwise 2 complete turns by
hand to ensure that no injectors are bottoming
out on their plungers.
18.Fit camshaft cover gasket.See this Section.
19.Fit cooling fan.See COOLING SYSTEM,
Repair.GASKET - COVER - CAMSHAFT
Service repair no - 12.29.40
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Release clip and disconnect breather hose from
camshaft cover.
5.Remove 13 bolts, spacers and sealing washers
from camshaft cover.
6.Remove camshaft cover and gasket.
Refit
7.Clean camshaft cover and mating face.
8.Renew sealing washers and spacers as
necessary.
ProCarManuals.com

12ENGINE
14
REPAIR
9. Not EU3 model:-Apply two 3 mm diameter
beads of sealant, Part No.STC 5433 to areas’A’
shown on illustration.
CAUTION: Excessive use of sealant could
result in blockage of oil drain hole,
arrowed’B’in illustration.
10.Fit new gasket to camshaft cover. fit cover and
tighten bolts to10 Nm (7 lbf.ft).
11.Position breather hose and secure clip.
12.Fit engine acoustic cover.
13.Reconnect battery negative lead.
14.Fit battery cover.ENGINE AND ANCILLARIES
Service repair no - 12.41.01.99
Remove
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Drain engine oil.
3.Remove radiator.See COOLING SYSTEM,
Repair.
4.Remove turbocharger.See FUEL SYSTEM,
Repair.
5.Remove starter motor.See ELECTRICAL,
Repair.
6.Remove air filter.See FUEL SYSTEM, Repair.
7.Loosen clip screw and release air intake hose
from intake elbow.
8.Release clips and disconnect coolant hoses
from fuel cooler and coolant rail.
ProCarManuals.com

ENGINE
15
REPAIR
NOTE: Non EU3 model illustrated.
9.Disconnect fuel hoses, tank to fuel cooler and
connector block on cylinder head.
CAUTION: Plug the connections.
10.Disconnect fuel hose from fuel cooler and secure
to connector block on cylinder head. This to
prevent contamination of the fuel system.
11.Release servo vacuum pipe, remove 4 bolts and
remove fuel cooler.
12.Release servo vacuum pipe from engine rear
cover clips and vacuum pump.
NOTE: Non EU3 model illustrated.
13.Disconnect vacuum hose from EGR valve.
14.Release EGR vacuum hose from vacuum pipe.
15.Disconnect multiplug from condensor cooling
fan.
NOTE: Non EU3 model illustrated.
16.Disconnect multiplugs from EGR solenoid, inlet
manifold sensor and injector harness.
ProCarManuals.com

12ENGINE
16
REPAIR
NOTE: Non EU3 model illustrated.
17.Disconnect multiplug from fuel temperature
sensor.
18.Disconnect multiplug from CKP sensor. Remove
bolt securing CKP sensor, remove sensor and
discard’O’ring.
CAUTION: If fitted:- Retain CKP sensor
spacer.
19.Disconnect 4 glow plug leads.
20.Remove nut securing alternator lead and
disconnect multiplug.
NOTE: Non EU3 model illustrated.
21.Remove 2 bolts securing engine harness to
camshaft carrier.
22.Disconnect A/C compressor and ECT sensor
multiplugs.
ProCarManuals.com

ENGINE
17
REPAIR
23.Disconnect oil pressure switch multiplug.
24.Release engine harness from underside of inlet
manifold and tie aside.
25.Release clips and remove coolant top hose from
cylinder head and coolant rail.
26.Remove 4 bolts and move A/C compressor
aside.
27.Remove 3 bolts and remove PAS pump pulley.
28.Remove 4 bolts and move PAS pump aside.
29.Raise vehicle on ramp.
30.Remove 6 bolts securing gearbox housing to
engine.
31.Lower vehicle ramp.
32.Remove 2 upper bolts securing gearbox housing
to engine.
33.Remove bolt securing engine closing panel to
gearbox.
34.Release clip and coolant hose from engine oil
cooler.
ProCarManuals.com

12ENGINE
18
REPAIR
35.Remove 2 bolts and remove acoustic cover from
rear of cylinder head.
36.FitLRT-12-138to suitable lifting chains and
connect to lifting eyes on engine.
37.Remove 2 nuts from RH and LH front engine
mountings.
38.Fit trolley jack to support gearbox.
39.With assistance raise chains and remove engine
from vehicle.Refit
40.With assistance, raise engine from bench and
position in vehicle.
41.With assistance, align engine to gearbox input
shaft.
42.Position 2 upper bolts securing gearbox housing
to engine and tighten to50 Nm (37 lbf.ft).
43.Lower engine onto mountings and tighten nuts to
85 Nm (63 lbf.ft).
44.RemoveLRT-12-138from engine.
45.Fit and tighten bolt securing engine closing panel
to gearbox.
46.Raise vehicle on ramp.
47.Fit bolts securing gearbox housing to engine and
tighten to50 Nm (37 lbf.ft).
48.Lower ramp.
49.Fit acoustic cover to rear of cylinder head and
tighten bolts.
50.Position coolant hose to engine oil cooler and
secure clip.
51.Position PAS pump and tighten bolts to25 Nm
(18 lbf.ft).
52.Position PAS pulley and tighten bolts to25 Nm
(18 lbf.ft).
53.Position A/C compressor and tighten bolts to25
Nm (18 lbf.ft).
54.Route engine harness beneath inlet manifold
and connect multiplugs to oil pressure switch,
A/C compressor, and ECT sensor.
55.Fit and tighten bolts securing engine harness to
camshaft carrier.
56.Connect multiplug to alternator.
57.Connect battery lead to alternator and tighten
nut.
58.Clean CKP sensor and mating face.
CAUTION: If originally fitted:- Fit spacer to
CKP sensor.
59.Using a new’O’ring, fit CKP sensor, tighten bolt
to10 Nm (7 lbf.ft).
60.Connect CKP sensor multiplug.
61.Connect multiplugs to EGR solenoid, inlet
manifold sensor, injector harness, fuel
temperature sensor and CKP sensor.
62.Connect glow plug leads.
63.Connect multiplug to condensor cooling fan.
64.Connect vacuum hose to EGR valve.
65.Connect EGR vacuum hose to vacuum pipe.
66.Position pipe to vacuum pump and secure pipe
to acoustic cover clips.
67.Position fuel cooler. Apply Loctite 242 to bolts
and tighten to18 Nm (13 lbf.ft).
68.Disconnect fuel hose from connector block and
connect to fuel cooler.
69.Connect fuel hoses to fuel cooler and connector
block on cylinder head.
ProCarManuals.com

ENGINE
19
REPAIR 70.Connect coolant hoses to fuel cooler and coolant
rail and secure clips.
71.Fit air intake hose to intake elbow and tighten
clip screw.
72.Fit starter motor.See ELECTRICAL, Repair.
73.Fit turbocharger.See FUEL SYSTEM, Repair.
74.Fit radiator.See COOLING SYSTEM, Repair.
75.Fit air filter.See FUEL SYSTEM, Repair.
76.Fill engine with oil.
77.Fit underbelly panel.See CHASSIS AND
BODY, Repair.MOUNTING - FRONT - LH
Service repair no - 12.45.01
Remove
1.Remove centrifuge assembly.See this
Section.
2.Remove 3 bolts, remove oil filter adaptor
housing and discard gasket.
3.Fit suitable lifting chains to support engine.
4.Remove 2 nuts securing engine mounting to
chassis.
5.Remove 4 bolts securing engine mounting
bracket to cylinder block.
6.Remove nut securing mounting to mounting
bracket.
7.Remove mounting and mounting bracket.
8.Remove mounting shield.
ProCarManuals.com