1999 LAND ROVER DEFENDER Workshop Manual

86ELECTRICAL
24
DESCRIPTION AND OPERATION ELECTRIC FRONT WINDOWS - FROM 02MY
1.LH and RH window lift switches
2.Motor and regulator assembly
3.Seat heat/Window lift relay
ProCarManuals.com

ELECTRICAL
25
DESCRIPTION AND OPERATION Electric window lift is a new feature for 02MY. The electric windows are only available on the front driver and
passenger doors. Rear passenger doors retain the manual window lift regulator mechanism.
The window lift system comprises a window motor in each front door, two window lift switches located in the fascia
switch panel and a relay, located adjacent to the passenger compartment fusebox. The windows are only
operative when the ignition switch is in position II.
Each window lift motor is located in the door, behind the trim casing. The motor and regulator form a handed
assembly and are not available separately as serviceable items.
The window lift relay receives a permanent battery feed via fusible links 1 and 3 in the under seat fuse box. The
relay coil has one side connected to earth with the other side receiving a feed from the ignition switch position II.
When the ignition is in position II, the relay is energised and battery voltage is supplied to each of the window lift
switches. On vehicles with heated seats, the relay is shared with the heated seat circuit.
Each switch has two wires to its applicable motor. When the switch is operated in either the up or down position,
one wire is supplied with a feed and the other is connected to earth as applicable for the selection made.
Each motor has thermal cut-out protection. If the window reaches the top or bottom limit of its travel or an object
obstructs the window, the thermal cut-out will sense the increased load on the motor and cut the power supply to
the motor brush contacts.
The cut-out time is between 3.5 to 5.0 seconds, with a time to restart of between 1 to 10 seconds. These figures
are based on an ambient temperature of 20°C (68°F) and a voltage of 13.5V.
ProCarManuals.com

86ELECTRICAL
26
DESCRIPTION AND OPERATION PASSENGER COMPARTMENT FUSE BOX
FROM 02MY
The increase in electrical systems on Defender 02MY vehicles has necessitated an increase in the number of
fuses required.
The passenger compartment fuse box now contains three rows of fuses instead of the previous two rows and
relays to control the CDL system, heated front screen, headlamps, anti-theft alarm ECU and seat heaters and
window lift system.
1.Fuse 8 - Anti-theft alarm ECU/BBUS (10A)
2.Fuse 9 - Front wiper motor and washer pump
(15A)
3.Fuse 10 - Rear wiper relay (10A)
4.Fuse 11 - ABS ECU (10A)
5.Fuse 12 - Engine Control Module (10A)
6.Fuse 13 - Brake pedal switch (10A)
7.Fuse 14 - Reverse lamp switch/Glowplugs (10A)
8.Fuse 15 - Miscellaneous relay control. See
Electrical Library (5A)
9.Fuse 16 - Cigar lighter/Heater blower (20A)
10.Fuse 17 - Radio (5A)
11.Fuse 18 - LH side lamps/trailer pick up (10A)
12.Fuse 19 - RH side lamps/trailer pick up (10A)
13.Fuse 20 - Headlamp levelling/Illumination (10A)
14.Fuse 21 - Direction indicators (10A)
15.Fuse 22 - RH headlamp dip beam (10A)
16.Fuse 23 - LH headlamp dip beam (10A)
17.Fuse 24 - RH headlamp main beam (10A)
18.Fuse 25 - LH headlamp main beam (10A)19.Fuse 26 - Rear fog lamp ECU (10A)
20.Fuse 27 - Alarm relay (10A)
21.Fuse 28 - Air conditioning blower relay (30A)
22.Fuse 29 - Air conditioning compressor
relay/cooling fan relay (20A)
23.Fuse 30 - Interior lamps/radio/alarm
LED/clock/diagnostic socket/tachometer (South
African vehicles only) (5A)
24.Fuse 31 - Hazard warning lamps (15A)
25.Fuse 32 - Heated rear window (20A)
26.Fuse 33 - Seat heat relay (20A)
27.Fuse 34 - RH window lift switch (20A)
28.Fuse 35 - LH window lift switch (20A)
29.Fuse 36 - Heated front screen (30A)
30.Relay - Heated Front Screen
31.Relay - Starter motor
32.Relay - Heated Rear Window
33.Relay - Headlamps
34.Relay - Anti-theft alarm
35.Relay - Seat heat/window lift
ProCarManuals.com

ELECTRICAL
27
DESCRIPTION AND OPERATION UNDER SEAT FUSE BOX
FROM 02MY
1.A/C Relay (if fitted)
2.A/C relay (if fitted)
3.Glow plug relay
4.Main relay
5.Fuel pump relay
6.ABS Return pump relay
7.Fuse 7 - Central Door Locking (CDL) and BBUS
(20A)
8.Fuse 6 - Anti-theft alarm ECU (15A)
9.Fuse 5 - Main relay (30A)10.Fuse 4 - Fuel pump relay (20A)
11.Fuse 3 - Horn/HRW relay (20A)
12.Fuse 2 - Accessory socket (20A)
13.Fuse 1 - ABS ECU (30A)
14.Fusible link 6 - Lights (30A)
15.Fusible link 5 - Ignition switch/Starter relay (60A)
16.Fusible link 4 - ABS Pump relay (30A)
17.Fusible link 3 - Window lift/Seat heat relay (60A)
18.Fusible link 2 - Air conditioning (60A)
19.Fusible link 1 - Glow plugs/Heated front screen
(100A)
ProCarManuals.com

86ELECTRICAL
28
DESCRIPTION AND OPERATION
ProCarManuals.com

ELECTRICAL
1
ADJUSTMENT HEADLAMPS - ALIGN BEAM
Service repair no - 86.40.17
Check
1.Align suitable beam setting equipment to
headlamp.
2.Ensure headlamp height adjustment switch set
to’O’and headlamps switch on.
Headlamp setting = 1.2% below horizontal and
parallel.
Adjust
3.Align beam setting equipment to 2nd headlamp
and adjust 2nd lamp as necessary.
4.Switch off headlamps.
5.Remove beamsetter.SOLENOID/MOTOR - FRONT DOOR - ADJUST
Service repair no - 86.26.21
Adjust
1.Remove door trim casing.See CHASSIS AND
BODY, Repair.
M86 5629
2.Carefully peel back plastic sheet to expose
mechanism.
3.Release clip and detach solenoid link from latch.
M86 5630
4.Ensure sill button is fully raised.
5.Fully extend solenoid actuator then lower 3.5
mm +/- 1.00 mm.
6.Whilst holding actuator in this position, adjust
length of link, until link pin is aligned with hole in
latch lever.
7.Connect link and secure with clip.
8.Secure plastic sheet.
9.Fit door trim casing.See CHASSIS AND
BODY, Repair.
ProCarManuals.com

ProCarManuals.com

ELECTRICAL
1
REPAIR BELT - AUXILLARY DRIVE
Service repair no - 86.10.03
Remove
1.Remove cooling fan.See COOLING SYSTEM,
Repair.
2.Release drive belt tensioner using a 15 mm ring
spanner and release belt from pulleys.
Refit
3.Clean drive belt pulley grooves and ensure
grooves are not damaged.
4.Fit new drive belt around pulleys, ensure belt is
correctly aligned in pulley grooves.
5.With assistance, hold tensioner fully clockwise
and fit drive belt around remaining pulley.
6.Fit cooling fan.See COOLING SYSTEM,
Repair.HARNESS - INJECTORS
Service repair no - 86.70.22
Remove
1.Remove camshaft cover gasket.See ENGINE ,
Repair.2.Disconnect engine harness from injector
harness.
3.Disconnect multiplugs from injectors.
4.Release injector harness from camshaft carrier
and remove harness.
Refit
5.Fit new’O’rings to injector harness connector.
6.Position harness and locate connector to
camshaft carrier.
7.Connect injector and engine harness multiplugs.
8.Fit camshaft cover gasket.See ENGINE ,
Repair.
ProCarManuals.com