1999 LAND ROVER DEFENDER battery location

ENGINE MANAGEMENT SYSTEM
1
REPAIR ENGINE CONTROL MODULE (ECM)
Service repair no - 18.30.03
Remove
1.Release fixings and remove battery cover.
2.Disconnect battery negative lead.
3.Remove RH seat cushion, release clip and
remove ECM access panel.
4.Remove 3 bolts, release ECM and disconnect 2
multiplugs. Remove ECM.
Refit
5.Position new ECM and connect multiplugs.
6.Fit ECM and tighten bolts.
7.Fit access panel and RH seat cushion.
8.Reconnect battery negative lead.
9.Fit battery cover and secure with fixings.SENSOR - ENGINE COOLANT TEMPERATURE
(ECT)
Service repair no - 18.30.10
Remove
1.Disconnect battery negative lead.
2.Remove spring clip and disconnect ECT sensor
multiplug.
3.Position cloth around ECT sensor to absorb
coolant spillage.
4.Remove ECT sensor.
5.Remove sealing washer and discard.
Refit
6.Clean sealing washer, sensor threads and
sensor location.
7.Coat sensor threads with Loctite 577 and fit new
sealing washer.
8.Fit ECT sensor and tighten to20 Nm (14 lbf.ft).
9.Fit spring clip to multiplug and connect multiplug
to ECT sensor.
10.Top up cooling system.
11.Run engine to normal operating temperature.
Check for leaks around ECT sensor.
12.Reconnect battery negative lead.
ProCarManuals.com

77PANEL REPAIRS
4
REPAIR SCREEN APERTURE
Remove
1.Disconnect both battery leads, negative lead
first.
2.Raise side of vehicle.
3.Remove front and centre headlining sections.
4.Remove both’A’post upper trims.
5.Remove front door aperture seals.
6.Release upper front corner of rear door aperture
seal.
7.Remove both wiper arms.See WIPERS AND
WASHERS, Repair.
8.Remove front screen.
9.Remove all roof fixings, back to the’B/C’post.
10.Release sealant securing front edge of roof.
11.Insert wedges into top of both’B/C’posts. This
will allow access for removal of screen aperture.
12.With assistance remove screen aperture.Refit
13.Prepare and clean panel joint faces.
14.Reverse removal procedure. Fit new foam seal
to top edge of aperture.
NOTE: When refitting, ensure screen
aperture is correctly fitted onto location
pins in bulkhead.
15.When applying sealant to top edge of aperture,
the correct colour sealant must be used, see
note below.
NOTE: White roof vehicles use a white
sealant. Coloured roof vehicles use a
black sealant.
ProCarManuals.com

77PANEL REPAIRS
6
REPAIR CORNER CAPPING
The Corner Capping is not replaced as a single panel.
It is replaced in conjunction with either the Body Side
Lower Panel or Body Side Assembly. The procedure
to replace the Corner Capping is shown in the Body
Side Lower Panel procedure.
BODY SIDE CAPPING
The Body Side Capping is not replaced as a single
panel. It is replaced in conjunction with either the
Body Side Lower Panel or Body Side Assembly. The
procedure to replace the Body Side Capping is shown
in the Body Side Lower Panel procedure.
BODY SIDE REAR - UPPER
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove front, centre and rear sections of
headlining.
3.Release upper edge of front door aperture seal.
4.Release upper edge of rear door aperture seal.
5.Remove fixings from front edge of roof, and
along side being replaced.
6.Release sealant securing front edge of roof.
7.Insert wedges into top of both’B/C’posts. This
will allow access for removal of body side.
8. RH side:Remove tail door.See CHASSIS
AND BODY, Repair.
9.Remove side window.
10.Remove rear sixth light.
11.Remove all bolts securing upper body side.
Refit
12.Prepare and clean panel joint faces.
13.Reverse removal procedure.
NOTE: When refitting, ensure body side
upper is correctly fitted onto location pins.
ProCarManuals.com

PANEL REPAIRS
7
REPAIR BODY SIDE REAR - LOWER - ASSEMBLY
In this procedure the Body Side Capping and the
Corner Capping are also changed.
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove body side upper rear.See this
Section.
3.Remove all rear lamps and reflectors.
4. LH side:Remove number plate and lamp.
5. LH side:Remove tail door striker.
6. RH side:Remove fuel filler and grommet.
7.Remove all bolts and rivets securing lower body
side assembly.
Refit
8.Prepare and clean panel joint faces.
9.Reverse removal procedure.
NOTE: When refitting, ensure body side
upper is correctly fitted onto location pins.
ProCarManuals.com

77PANEL REPAIRS
8
REPAIR BODY SIDE REAR - PANEL
Remove
In this procedure the Body Side Capping and the
Corner Capping are also changed.
1.Disconnect both battery leads, negative lead
first.
2.Remove body side upper rear.See this
Section.
3.Remove rear lamp panel.See this Section.
4. LH side:Remove number plate and lamp.
5. LH side:Remove tail door striker.
6. RH side:Remove fuel filler and grommet.
Refit
7.Prepare and clean panel joint faces. Drill holes in
new body side lower panel for riveting. Spacing
of holes, dimension’A’= 100 mm (3.937’). In
conjunction with the rivets apply suitable
adhesive.
8.Prepare and clean panel joint faces.
9.Reverse removal procedure.
NOTE: When refitting, ensure body side
upper is correctly fitted onto location pins.
ProCarManuals.com