ENGINE
17
DESCRIPTION AND OPERATION The engine oil cooler assembly is located on the left hand side of the engine block behind the oil centrifuge and oil
filter. The housing is bolted to the engine block by seven bolts. A matrix is included in the oil cooler housing which
acts as a heat exchanger. Coolant flow circulates through the oil cooler housing under pressure from the coolant
pump and distributes the flow evenly around the matrix fins and then along the block into three core holes for
cylinder cooling. Coolant enters the oil cooler through a pipe with a rubber hose extension at the rear side of the
engine. The coolant hose is attached to the stub pipe of the oil cooler by a spring clip.
Oil, drawn from the sump by the oil pump, passes through the oil cooler via the cylinder block. The flow of coolant
around the exterior surface of the oil cooler matrix cools a proportion of the engine oil flow as it passes through the
oil cooler.
The oil cooler is sealed to the cylinder block by a gasket which must be replaced every time the oil cooler housing
is removed.
ProCarManuals.com
ENGINE MANAGEMENT SYSTEM
27
DESCRIPTION AND OPERATION The turbocharger is exposed to extremely high operating temperatures (up to 1000°C, 1832°F) because of the
hot exhaust gases and the high speed revolution of the turbine (up to 15,000 rev/min). In order to resist wear of
the turbine bearings a flow of lubrication oil is supplied from the engine lubrication system to keep the bearings
cool. Oil is supplied from a tapping at the front of the full-flow filter adaptor housing via a metal pipe with banjo
connections. Oil is returned to the sump via a metal pipe which connects to the cylinder block at a port below the
turbocharger assembly.
A heatshield is attached to the LH side of the engine to protect adjacent components from the heat generated at
the turbocharger. The heatshield is attached to the engine by 2 bolts. An additional bolt attaches the heatshield to
the turbocharger casting.
The ECM controls the amount of boost pressure the engine receives by way of the turbocharger. When full boost
is reached a control signal is sent to the wastegate modulator, and a vacuum is applied to the wastegate valve.
The wastegate valve opens, bypassing some of the exhaust gases away from the turbine to be output to the
exhaust system.
The engine should be allowed to idle for 15 seconds following engine start up and before the engine is switched
off to protect the turbocharger by maintaining oil supply to the turbine bearings.
INTERCOOLER
The intercooler is an air-to-air heat exchanger which lowers the intake air temperature to obtain a higher air
density for better combustion efficiency. The intercooler receives compressed air from the turbocharger via a
metal pipe. It cools the intake air via the intercooler matrix and delivers it to the intake manifold by means of a
rubber hose which connects between the intercooler outlet and the intake manifold. The rubber hose is connected
to ports at each end by metal clips.
The intercooler is located at the front of the engine bay, forward of the radiator.
ProCarManuals.com
COOLING SYSTEM
7
DESCRIPTION AND OPERATION Radiator
The 44 row radiator is located at the front of the vehicle in the engine compartment. The cross flow type radiator is
manufactured from aluminium with moulded plastic end tanks interconnected with tubes. The bottom four rows are
separate from the upper radiator and form the lower radiator for the fuel cooler. Aluminium fins are located
between the tubes and conduct heat from the hot coolant flowing through the tubes, reducing the coolant
temperature as it flows through the radiator. Air intake from the front of the vehicle when moving carries the heat
away from the fins. When the vehicle is stationary, the viscous fan draws air through the radiator fins to prevent
the engine from overheating.
Two connections at the top of the radiator provide for the attachment of the top hose from the outlet housing and
bleed pipe to the expansion tank. Three connections at the bottom of the radiator allow for the attachment of the
bottom hose to the thermostat housing and the return hose from the oil cooler and the feed hose to the fuel cooler.
The bottom four rows of the lower radiator are dedicated to the fuel cooler. The upper of the two connections at
the bottom of the radiator receives coolant from the oil cooler. This is fed through the four rows of the lower
radiator in a dual pass and emerges at the lower connection. The dual pass lowers the coolant temperature by up
to 24°C before being passed to the fuel cooler. Two smaller radiators are located in front of the cooling radiator.
The upper radiator is the intercooler for the air intake system and the lower radiator provides cooling of the
gearbox oil.
Pipes and Hoses
The coolant circuit comprises flexible hoses and metal formed pipes which direct the coolant into and out of the
engine, radiator and heater matrix. Plastic pipes are used for the bleed and overflow pipes to the expansion tank.
A bleed screw is installed in the radiator top hose and is used to bleed air during system filling. A drain plug to
drain the heater and cylinder block circuit of coolant is located on the underside of the coolant pump feed pipe.
Oil Cooler
The oil cooler is located on the left hand side of the engine block behind the oil centrifuge and oil filter. Oil from the
oil pump is passed through a heat exchanger which is surrounded by coolant in a housing on the side of the
engine.
Full water pump flow is directed along the cooler housing which also distributes the flow evenly along the block
into three core holes for cylinder cooling. This cools the engine oil before it is passed into the engine. A small
percentage of the coolant from the oil cooler passes into a metal pipe behind the engine. It then flows into the
lower radiator via a hose.
Fuel Cooler
The fuel cooler is located on the right hand side of the engine and is attached to the inlet manifold. The cooler is
cylindrical in design and has a coolant feed connection at its forward end. A’T’connection at the rear of the cooler
provides a connection for the coolant return from the heater matrix and coolant return from the fuel cooler.
The’T’connection houses a thermostat which opens at approximately 82°C. This prevents the cooler operating in
cold climates. Two quick release couplings on the cooler allow for the connection of the fuel feed from the
pressure regulator and return to the fuel tank. A counter flow system is used within the cooler.
Fuel flows around a coolant jacket within the cooler and flows from the back to the front of the cooler. As the hot
fuel cools travelling slowly forwards it meets progressively colder coolant travelling in the opposite direction
maintaining a differential cooling effect.
ProCarManuals.com
COOLING SYSTEM
11
DESCRIPTION AND OPERATION OPERATION
Coolant Flow - Engine Warm Up
During warm up the coolant pump moves fluid through the cylinder block and it emerges from the outlet housing.
From the outlet housing, the warm coolant flow is prevented from flowing through the upper and lower radiators
because both thermostats are closed. The coolant is directed into the heater circuit.
Some coolant from the by-pass pipe can pass through small sensing holes in the flow valve. The warm coolant
enters a tube in the thermostat housing and surrounds 90% of the thermostat sensitive area. Cold coolant
returning from the radiator bottom hose conducts through 10% of the thermostat sensitive area. In cold ambient
temperatures the engine temperature can be raised by up to 10°C (50°F) to compensate for the heat loss of the
10% exposure to the cold coolant return from the radiator bottom hose.
At engine speeds below 1500 rev/min, the by-pass valve is closed only allowing the small flow through the sensing
holes. As the engine speed increases above 1500 rev/min, the greater flow and pressure from pump overcomes
the light spring and opens the by-pass flow valve. The flow valve opens to meet the engine’s cooling needs at
higher engine speeds and prevents excess pressure in the cooling system. With both thermostats closed,
maximum flow is directed through the heater circuit.
The heater matrix acts as a heat exchanger reducing the coolant temperature as it passes through the matrix.
Coolant emerges from the heater matrix and flows to the fuel cooler’T’connection via the heater return hose.
From the fuel cooler the coolant is directed into the coolant pump feed pipe and recirculated around the heater
circuit. In this condition the cooling system is operating at maximum heater performance.
Coolant Flow - Engine Hot
As the coolant temperature increases the main thermostat opens. This allows some coolant from the outlet
housing to flow through the top hose and into the radiator to be cooled. The hot coolant flows from the left tank in
the radiator, along the tubes to the right tank. The air flowing through the fins between the tubes cools the coolant
as it passes through the radiator.
A controlled flow of the lower temperature coolant is drawn by the pump and blended with hot coolant from the
by-pass and the heater return pipes in the pump feed pipe. The pump then passes this coolant, via the cylinder
block, to the oil cooler housing, cooling the engine oil before entering the block to cool the cylinders.
When the fuel temperature increases, the heat from the fuel conducts through the fuel cooler’T’connection and
causes the fuel thermostat to open. Coolant from the cylinder block flows through the oil cooler and via a pipe and
hose enters the lower radiator. The lower temperature coolant from the oil cooler housing is subjected to an
additional two passes through the lower radiator to further reduce the coolant temperature. From the lower radiator
the coolant flows , via a hose, to the fuel cooler.
As the hot fuel cools, travelling slowly forwards through the cooler, it meets the progressively colder coolant
travelling in the opposite direction from the lower radiator.
ProCarManuals.com