1999 LAND ROVER DEFENDER Workshop Manual

86ELECTRICAL
16
DESCRIPTION AND OPERATION CDL Using the Key
The driver and the passenger front doors are fitted with key barrel locks. Using the vehicle key in the passenger
door will only lock or unlock that door. Using the key in the drivers door will operate the CDL system and lock or
unlock all doors.
NOTE: The passenger door key barrel is connected to the door latch and has no electrical input to
the anti-theft alarm ECU. The driver door key barrel is also connected to the door latch and its
operation is monitored by the ECU only via the latch motor and the two wires connected to it.
When the vehicle is locked using the key in the drivers door, only CDL and perimetric protection is invoked.
Volumetric protection and active immobilisation is not initiated.
CDL Using the Remote Handset
The remote handset has two buttons; lock and unlock. A single press on the lock button will lock all doors and
invoke perimetric and volumetric protection and active immobilisation. Remote locking is inhibited if the
transponder coil senses that the key is in the ignition switch.
When the vehicle is locked, a single press of the unlock button will unlock all doors and disable perimetric and
volumetric protection. Immobilisation is only disabled using the transponder coil and the remote handset or the
EKA procedure.
Security LED
In addition to the alarm system status indications, the security LED also displays CDL system status.
The system confirms that the drivers door is open by illuminating the LED for the 10 second confirmation period. If
any other door or the bonnet is open, the LED remains unlit for the 10 second confirmation period. After the 10
second confirmation period the LED reverts to the slow flash deterrent mode if the alarm is armed.
ProCarManuals.com

ELECTRICAL
17
DESCRIPTION AND OPERATION Interior Lamp Functionality
The anti-theft alarm ECU controls the interior lamp functionality. When the lamps are extinguished, they fade out
to the off condition over a 2 second period.
The lamps are turned on by:
Disarming the alarm using the remote handset
Opening any door.
When the lamps are on, they will be extinguished by the following actions:
If all doors are closed, the lamps will be extinguished after a 15 second delay period
If any door is left open, the lamps will be extinguished after an 8 minute delay period
If one of the above delay periods is active and the ignition is switched on or the alarm is armed, the lamps will
be extinguished.
ANTI-THEFT ALARM SYSTEM SELF TEST
The anti-theft alarm ECU has a self test feature which allows all alarm inputs to be tested. To enter self test mode
the following steps must be completed as follows:
1.Ensure that the driver’s door is closed and the driver’s window is open
2.Open the bonnet and with assistance depress and hold the bonnet switch
3.Release the bonnet switch and within 0.5 seconds turn the ignition switch on to position II
4.Quickly open the driver’s door
5.Turn the ignition switch to the off position
6.Turn the ignition switch back to position II
7.If the self test mode has been entered successfully, confirmation will be given by the alarm sounder. If the
ECU has not entered self test mode, repeat the above procedure.
Once in self test mode, the following test inputs will cause the security LED to illuminate and the engine
immobilised warning lamp and the hazard warning lamps to flash. When an input is operated, non illumination of
the security LED, the engine immobilised warning lamp and the hazard warning lamps indicates a fault for that
input.
Perform the following steps to test each input for correct operation:
Close and open the drivers door
Open and close each of the passenger doors and the tail door in turn
Close and open the bonnet (depress switch if bonnet still open)
With drivers door closed, lock and unlock the driver’s door using the vehicle key if spare key available. If spare
key is not available, operate driver’s sill button through open window
Press the unlock button of the remote handset. This enters the volumetric self test mode and all other inputs
will be disabled. Make a movement inside the vehicle. When the volumetric sensor is triggered the security
LED will flash.
To exit the self test mode, turn the ignition switch to the off position.
ProCarManuals.com

86ELECTRICAL
18
DESCRIPTION AND OPERATION FASCIA CONSOLE
1.Rear fog lamp switch
2.Rear wiper switch
3.Heated front screen switch (if fitted)
4.Hazard warning lamp switch
5.Heated rear window switch
6.Rear washer switch
7.Front fog lamps switch (if fitted)8.RH front window switch
9.RH heated front seat switch (if fitted)
10.Headlamp levelling control switch
11.Cigar lighter (if fitted)
12.LH heated front seat switch (if fitted)
13.LH front window switch
ProCarManuals.com

ELECTRICAL
19
DESCRIPTION AND OPERATION For 02MY a new fascia console has been introduced to accommodate the additional switches for electric windows
etc.
The console comprises a plastic moulding secured to the fascia with five screws. The new console allows existing
switches to be repositioned and has provided the opportunity to commonise the switches with other Land Rover
models. The switches and components located in the console are as follows:
Cigar lighter (if fitted)
Headlamp levelling control
LH and RH heated front seat switches (if fitted)
LH and RH front window lift switches
Front fog lamp switch (if fitted)
Rear fog lamp switch
Rear wash/wipe switch
Rear wiper switch
Hazard warning lamp switch
Heated rear window switch
Heated front screen switch (if fitted)
A central cut-out in the console provides for the installation of the radio, where fitted, or a coin tray for markets
without a standard radio installation.
ProCarManuals.com

86ELECTRICAL
20
DESCRIPTION AND OPERATION HEATED FRONT SCREEN - FROM 02MY
1.Heated front screen RH connector
2.Heated front screen LH connector
3.Heated front screen ECU (behind instrument pack)
4.Heated front screen relay (passenger compartment fuse box)
5.Heated front screen switch
ProCarManuals.com

ELECTRICAL
21
DESCRIPTION AND OPERATION The Heated Front Screen (HFS) is a new feature for 2002MY which is available as part of a cold climate pack on
Td5 engine variants only. The HFS system comprises an HFS ECU, an HFS relay, a controlling switch and the
HFS elements.
The HFS comprises two elements laminated in the windscreen. The elements are connected by bus bars within
the screen and therefore the HFS has only one feed and one earth connector.
The HFS is controlled by the HFS ECU which determines when HFS operation is permitted. The ECU also has a
timer which allows HFS operation for up to 8 minutes. The HFS ECU is located behind the instrument pack,
adjacent to the dim/dip relay. The ECU is connected by a multiplug. The ECU receives an ignition feed via the
satellite fuse box and an engine running signal from the engine oil pressure switch.
A non-latching switch for HFS operation is located in the fascia. The switch has a tell-tale lamp to indicate when
the HFS screen is operative.
The HFS relay is located in the under seat fuse box and receives a permanent battery voltage supply via fusible
link 1 in the under seat fuse box. The relay coil is connected to the HFS ECU and an earth point. When the relay is
operated, battery voltage is supplied from the relay, via fuse 25 in the passenger compartment fuse box to the
HFS element.
When the HFS switch is depressed, a momentary earth path is completed from the HFS ECU, through the switch
to earth. This is sensed by the ECU as a request for HFS operation. If the ECU receives an ignition on signal and
an oil pressure signal, it allows HFS operation. The ECU provides an output to the coil of the HFS relay. When the
coil is energised, the contacts close and battery voltage, via fusible link 1 in the under seat fuse box is supplied to
the HFS element, via fuse 25 in the passenger compartment fuse box. The feed is also supplied via a splice joint
to the HFS switch to illuminate the tell tale lamp in the switch.
The HFS ECU will allow screen operation for up to 8 minutes, after which it removes the feed to the HFS relay
coil, which, after the contacts open, removes the supply to the HFS element and simultaneously extinguishing the
tell tale lamp in the switch. If, during the timed operation period, the HFS ECU receives an additional request
signal from operation of the switch, HFS operation is stopped.
When operating, the HFS element draws approximately 25 Amps. To prevent excess drain on the vehicle battery,
if the ignition on signal and/or the oil pressure switch (engine running) signal is lost, the HFS ECU de-energises, if
already operating, or will not energise the HFS relay.
ProCarManuals.com

86ELECTRICAL
22
DESCRIPTION AND OPERATION HEATED FRONT SEATS - FROM 02MY
1.LH and RH seat heater switches
2.Seat heater cushion and squab elements
3.Seat heat/Window lift relay (passenger compartment fuse box)
ProCarManuals.com

ELECTRICAL
23
DESCRIPTION AND OPERATION Heated front seats are a new feature for 2002MY and are available as part of a cold climate pack on Td5 engine
variants only. The heated seats system comprises, two latching switches, a seat relay and heater elements.
The latching switches are located in the fascia. Each switch individually controls its related seat heater elements.
Each switch contains a tell tale lamp to indicate when the seat heaters are active. There is no timer function for the
seat heater operation and the seat heaters will remain active for as long as the switch is latched in and the ignition
is in position II.
The seat heater relay is located in the passenger compartment fuse box and shares its supply and operation with
the front window lift system. The relay receives a permanent battery voltage supply via fusible links 1 and 3 in the
under seat fuse box and fuse 28 in the satellite fuse box. The relay coil is connected to the ignition switch via fuse
7 in the passenger compartment fuse box and an earth point. When the ignition switch is moved to position II, the
relay coil is energised and the contacts close. Power is supplied from the relay to each of the seat heater
switches.
The heater elements are fitted in the seat cushion and squab on the drivers and passenger front seats and are
wired in series. The wiring looms for the elements is long enough to allow the seat squab to be lifted for access to
the under seat fuse box or the storage bin/battery without straining the wiring. The centre seat, if fitted, does not
have heater elements.
The cushion element receives the feed from the switch and contains a thermostatically controlled switch. When
the element temperature reaches 37±3°C (98±3°F) the thermostat cuts the supply to the cushion and squab
elements for that seat. As the temperature of the element falls to 28±3°C (82±3°F), the thermostat will close the
switch contacts allowing power to flow to both elements causing them to heat up again. In this way the thermostat
maintains the cushion and squab element temperatures between the figures stated.
ProCarManuals.com