86ELECTRICAL
12
DESCRIPTION AND OPERATION IMMOBILISATION SYSTEM - FROM 02MY
Engine immobilisation is available on all 2002MY engine derivatives, although it is not available in selected
markets. On Td5 models, the immobilisation system is controlled directly by the anti-theft alarm ECU. On 300Tdi
models, the immobilisation system is controlled by an engine immobilisation ECU in conjunction with the anti-theft
alarm ECU.
When immobilisation occurs on Td5 models, engine crank is disabled by the anti-theft alarm ECU breaking the
earth path for the starter relay coil and the ECM disables the fuel pump relay and the glow plug relay.
When immobilisation occurs on 300Tdi models, engine crank is disabled by the anti-theft alarm ECU breaking the
earth path for the starter relay coil and the engine immobilisation ECU disables the fuel cut-off solenoid, the starter
motor solenoid and the glow plug relay.
Two types of immobilisation are available; passive and active.
Engine Immobilised Warning Lamp
The engine immobilised warning lamp is located in the instrument pack. The lamp is used by the anti-theft alarm
ECU to show that the engine is immobilised during an attempted engine start.
The warning lamp receives a battery supply from the ignition switch position I (aux) via the passenger
compartment fusebox. The anti-theft alarm ECU controls the warning lamp. When the warning lamp is not
required, the ECU supplies a battery supply to the warning lamp. When warning lamp operation is required, the
ECU provides an earth for the bulb.
If the ignition switch is moved to the crank position, but operation of the starter motor is prohibited and the engine
immobilised warning lamp flashes, then the anti-theft alarm ECU has not received the correct code from the
remote handset and the vehicle will remain immobilised. Ensure that the remote handset is in the proximity of the
transponder coil. If the remote handset is not available or inoperative, the immobilisation system can be disarmed
using the EKA procedure outlined later in this section.
If the ignition switch is turned to the crank position III and the remote handset is not in the proximity of the
transponder coil, engine immobilisation will remain active and the warning lamp will flash to inform the driver.
ProCarManuals.com
86ELECTRICAL
14
DESCRIPTION AND OPERATION Emergency Key Access (EKA)
If the vehicle is in an immobilised condition and the remote handset is not available or inoperable, an EKA
procedure using the vehicle key is available to remobilise the engine systems. The EKA code is supplied with the
vehicle and is shown on the security card supplied with the owners handbook.
NOTE: This feature is only available in markets where full alarm functionality is specified.
The EKA code involves the input of a unique four digit code which is entered using the ignition switch and the
drivers door switch. Note that the alarm sounder will operate as soon as the drivers door is opened and will
continue until the sequence is successfully completed.
To enter the code (2, 3, 4, 5 for example) perform the following steps:
1.Remove the handset from the key ring and position the handset well away from the ignition switch when
entering the code.
2.Open the driver’s door and immediately insert the key in the ignition switch and turn the ignition switch to
position II. Hold this position until the alarm sounds, then switch the ignition off (position 0) and close the
driver’s door.
3.Enter the first digit of the code. Turn the ignition on (to position II) and then off twice. Open and close the
driver’s door to enter the first digit.
4.Enter the second digit. Turn the ignition on and then off, three times. Open and close the driver’s door to
enter the second digit.
5.Enter the third digit. Turn the ignition on and then off, four times. Open and close the driver’s door to enter
the third digit.
6.Enter the fourth digit. Turn the ignition on and then off, five times. Open and close the driver’s door to enter
the fourth digit. If the code has been entered correctly, the alarm LED in the instrument pack will extinguish
and the engine can be started after the last closure of the driver’s door.
If a digit is incorrectly entered, holding the ignition switch in the on position for more than 5 seconds will reset the
sequence. The code must then be re-entered from the beginning.
If the EKA code is correctly entered, the security LED will illuminate for 1 second, the immobilisation will be
disabled and the alarm sounder will cease to operate.
If the EKA code is incorrectly entered, the alarm sounder will sound twice and the correct code must be
re-entered, If the EKA code is incorrectly entered three times the system invokes a 30 minute lockout. This is
signalled by the LED flashing with a long illuminated period followed by a short extinguished period for the lockout
duration.
NOTE: Disabling the alarm and immobilisation system using the EKA procedure is only valid for
one ignition on/off cycle. When the ignition is switched off, the immobilisation system will be
activated after a period of 30 seconds. If the remote handset is still unavailable, the EKA
procedure will have to be repeated each time the vehicle is to be driven.
ProCarManuals.com
