1998 JAGUAR X308 brake

28. Using a h
ydraulic press,
remove hub from carrier.
Pla
ce large section of special tool (204-113) on press bed,
with recess in t ool uppermost.
Positi
on hub carrier on tool
, ensuring handbrake cable
housing locates in tool recess.
P o
sition small section of spec
ial tool (204-113) on hub.
Align tool to press-r
am, and
operate press to remove hub
from hub carrier.
29. Place hub carrier on a work bench.

30 . W
ithdraw ABS rotor from hub carrier.

31 . Remove ou
ter seal and bearin
g assembly from hub carrier.
Using a drift, re
move an
d discard outer seal.
Remove ou ter bearin
g.
Re
mo
ve bearin
g spacer.
Remove bearin g shim.
32
.
Remove inner seal and bearing from hub carrier.
Using a drift, re
move and discard inner seal.
Re

move inner bearing.

10
.
Install washer and nut on pivot pin, but DO NOT tighten nut.

11
.
Install hub on axle shaft .
Route parking brake cable throu
gh hub carrier aperture
and install grommet.
Appl
y Loctite 270 to axle shaft splines and thread, and
fully seat hub on shaft.

12
.
Install locating collar and hub nut on axle shaft, but DO NOT
tighten hub nut.
13. Tighten pivot pin nut.
Al
ign marker on pivot pin flange with mark made on
wishbone.
Ensuri
ng pin position is not
disturbed, tighten nut to 88-
118Nm.

14. Inst
all wheel speed sensor on hub carrier.
Posit
i
on sensor on hub carrier
and install and tighten bolt
to 7-10Nm.
Conne ct
wheel speed sensor harness to sensor.

15 . Using new ti
e strap, secure wh
eel speed sensor harness to
hub carrier.
16. Install handbrake shoes. Re fer to operation 70.40.05.
17. Install brake disc. Refer to operation 70.10.13.

18 . Posit
ion special tool (204-195)
on hub studs and install nuts.
19. Tighten hub nut to 304-336Nm.

20
.
Remove nuts and withdraw special tool (204-195) from hub.
21. Install rear wheel. Refer to Section 204-04.
22. Remove stands and lower vehi cle onto wheels. Refer to
section 100-02.
23. Raise vehicle on four-post lift.

24
.
Route parking brake cable through suspension mounting
bracket and secure with clip.

25
.
Route parking brake cable through equalizer (LH side cable
only).

26
.
Install parking brake cabl e in connecting clip.
27. Adjust parking brake cable. Refer to 70.35.10.
28. Lower four-post lift
29. Apply parking brake.
30. Carry out rear wheel alignm ent check and adjust as


necessary. Refer
t
o 204-02 Specification section.

Rear Su
spension - Wh
eel Knuckle Bushing
Remo
val and Installation
Remov
a
l
S
p
ecial Tool(s)

Hub Holdin
g Tool
2
04-195 (JD227)

Hub Pu
ller

204-011 (JD 1D)

D rive
r Handle
100-013 (18G-134)

Bearing Cu p Replacer Adaptor
2
04-120 (JD 550-6)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used. See section 100-00 for information.
Release parking brake.
2. Ra
ise the vehicle on a four-post lift.

3. Fully slacken bu
t do not remove parking brake cable adjuster
nut.
4. Release appropriate side parkin g brake cable from connecting

cli
p.

5. With
draw parking brake cable th
rough equalizer (LH side cable
only).
6. Lower four-post lift.
7. Raise rear of vehicle to workin g height and support on stands.
Refer to section 100-02.
8. Remove rear wheel. Refer to section 204-04.

9. Posit
ion special tool (204-1
95) on hub studs and install
securing nuts.

10
.
Slacken but do not remove hub to axle shaft securing nut.
11. Remove securing nuts from stud s and withdraw special tool
(204-195) from hub.
12. Remove rear brake disc. Refer to 70.10.13.
13. Remove parking brake shoe s. Refer to 70.40.05.
14. Remove wheel speed sensor.

19
.
Install a thread protector on axle shaft.

20
.
Release hub from axle shaft.
Position hu
b puller on hub studs. (204-011)
Inst

all securing nuts.
Progres

sively tighten
puller center bolt to release hub from
axle shaft splines.
21. Remove nuts and release puller from hub.
22. Remove thread protec tor from axle shaft.

23
.
Release handbrake cable from suspension mounting bracket.
Remove cable reta
ining clip.
Draw c

able through suspension mounting bracket
aperture.
24. Remove parking brake cable to hub carrier grommet.

25. Remove back plate.
Re
move four screws securing
back plate to hub carrier.
Withdraw back plate
complete
with parking brake cable.

26 . Remove h
ub and carrier.
With
draw pivot pin
.
R
e
move hub and carrier assemb
ly from wishbone and axle
shaft.

27 . R
emove shim from each end of pivot pin sleeve.
28. Withdraw pivot pin sleeve from hub carrier.