1998 JAGUAR X308 76.47.24

                    Front Doo r
 
Window  Regulator  and  Motor  (76.31.45)  
                     Front Door  Window  Regulator  Motor  (76.31.45)  
                     Front Door  Window  Control  Switch  (86.25.07)  
                     Rear Door  Window  Glass  (76.31.02)  
                     Rear Door  Window  Glass  Weatherstrip  (76.40.29)  
                     Rear Door  Window  Regulator  and  Motor  (86.25.09)  
                     Rear Door  Window  Regulator  Motor  (86.25.09)  
                     Rear Door  Window  Control  Swi
tch (86.25.10)  
                     Rear Quarter  Window  Glass  (76.31.31)  
                     Rear Window  Glass  (76.81.11)  
                     Windshield  Glass  (76.81.40)  
 
             501‐12:  Instrument  Panel  and  Console  
                 Specification  
                 Description  and  Operation  
                     Instrument  Panel  and Instrument  Panel  Console  
                 Removal and  Installation  
                     Audio Unit  Housing  (76.25.15)  
                     Climate Control Assembly  Housing 
                     Coin Stowage  Compartment (76.46.37)  
                     Floor Co
nsole  (76.25.01)  
                     Floor Console  Ashtray  (76.25.25)  
                     Floor Console  Extension  (76.25.05)  
                     Floor Console  Finish  Panel  (76.47.26)  
                     Floor Console  Finish  Panel  Bracket  (76.25.26)  
                     Floor Console  Stowage  Compartment  (76.25.16) 
                     Floor Console  Stowage  Compartment  Lid (76.25.18)  
                     Glove Compartment  (76.52.03) 
                     Glove Compartment  Lid (76.52.02)  
                     Glove Compartment  Lid Damper  (76.52.22)  
                     Glove Co
mpartment  Liner  (76.52.21)  
                     Instrument  Cluster  Finish Panel  (76.47.24)  
                     Instrument  Cluster  Finish Panel  Bezel  (88.20.33)  
                     Instrument  Panel  (76.46.01)  
                     Instrument  Panel  Finish Panel  (76.47.06)  
                     Instrument  Panel  Lower  Trim  Panel  (76.46.11)  
                     Overhead Console  (76.13.69)  

Air Distribution and Filtering - Center Registers
Removal and Installation
Removal
Installation

1.
Remove battery cover and disconnect ground cable from battery
terminal. Refer to 86.15.19.
2. Remove passenger airbag deployment door for access. Refer to
Section 501-20.
3. Remove major gauge module veneer panel for access. Refer to
76.47.24.
4. Carefully withdraw fascia centre veneer panel.

5. Slacken and remove four screws securing centre vent assembly
to fascia.
6. Withdraw centre vent assembly for access, disconnect clock
harness multiplug, release clock retaining tangs and remove clock
from vent assembly.

7. Remove and discard the four veneer panel to fascia securing
clips.
1. Fit and fully seat new veneer panel retaining clips to fascia.
2. Fit clock to centre vent assemb ly, ensuring retaining tangs are
fully seated.
3. Position centre vent assembly at fascia and connect clock
harness multiplug.
4. Fully seat vent assembly in fascia and fit and tighten securing
screws.
5. Fit and fully seat centre veneer panel.
6. Fit major gauge module veneer panel. Refer to 76.47.24.
7. Fit passenger airbag deployment door. Refer to Section 501-20.
8. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.

Instrume
nt Cluster - Instrument Cluster
Re
moval and Installation
Remov

al
1.
Adjust steer
ing column to full
y extended and lowered position.
2. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
3. Remove veneer from instrument panel. Refer to 76.47.24.

4. Using a small
screwdriver, de
press fog lamp switch upper
retaining tang and release sw itch from gauge surround.

5. Position fog l
amp switch fo
r access, disconnect harness
multiplug and remove switch.

6. Using a small
screwdriver, depress trip keyboard upper
retaining tang and release ke yboard from gauge surround.
7. Position trip keyboard for ac cess and disconnect harness
multiplug.

In
stallation


8.
Slac ken an
d remove four screws securing major gauge
module/surround to fascia and withdraw surround.

9. With draw major gau
ge module fo
r access, disconnect the two
harness multiplugs and remove gauge module from fascia.
1. Position major gauge module in fascia and connect both
harness multiplugs.
2. Position major gauge surround on panel, routing harness
multiplugs through apertures.
3. Fit and tighten screws securing major gauge module/surround
to fascia.
4. Connect harness multiplug to tr ip keyboard and fit and fully
seat keyboard in gauge surround, ensuring correct location of
retaining tangs
5. Connect harness multiplug to fog lamp switch and fit and fully
seat switch in gaug e surround, ensuring correct location of
tangs.
6. Fit veneer panel. Refer to 76.47.24.
7. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.
8. Return steering column to original position.

Information and Message Center - Message Center Switch
Removal and Installation
Removal
Installation

1.
Disconnect battery ground cable; refer to 86.15.19.
2. Remove instrument panel veneer panel; refer to 76.47.24.

3. Remove trip computer switch pack.
Use suitable small screwdriver to displace upper retaining
tang.
Reposition switch pack for access to connector.
Disconnect connector and remove switch pack.
1. Installation is reverse of removal.

Exterior Lighting - Fog Lamp Switch
Removal and Installation
Removal
Installation



1. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
2. Remove instrument pa nel veneer panel. Refer to 76.47.24.

3. Remove combined front and rear fog lamp switch pack.
Use a small screwdriver to re lease upper retaining tag.
Position switch for access to connector.
Disconnect connector and remove switch.
1. Position switch pack at instrument panel.
2. Connect harness connector to switch pack
3. Install switch pack in panel, ensuring that retaining tangs are
fully seated.
4. Install instrument panel veneer panel. Refer to 76.47.24.
5. Connect ground cable to batter y terminal and install battery
cover. Refer to 86.15.15.

Instrument Panel and Console - Instrument Cluster Finish Panel Bezel
Removal and Installation
Removal
1. Adjust steering column to full y extended and lowered position.
2. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
3. Remove veneer from instrument panel. Refer to 76.47.24.

4. Using a small screwdriver, de press fog lamp switch upper
retaining tang and release sw itch from gauge surround.

5. Position fog lamp switch fo r access, disconnect harness
multiplug and remove switch.

6. Using a small screwdriver, depress trip keyboard upper
retaining tang and release ke yboard from gauge surround.
7. Position trip keyboard for ac cess and disconnect harness
multiplug.

Installation




8. Slacken and remove four screws securing major gauge
module/surround to fascia and withdraw surround.
1. Position major gauge surround on panel, routing harness
multiplugs through apertures.
2. Fit and tighten screws securing major gauge module/surround
to fascia.
3. Connect harness multiplug to tr ip keyboard and fit and fully
seat keyboard in gauge surround, ensuring correct location of
retaining tangs
4. Connect harness multiplug to fog lamp switch and fit and fully
seat switch in gaug e surround, ensuring correct location of
tangs.
5. Fit veneer panel. Refer to 76.47.24.
6. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.
7. Return steering column to original position.