1998 JAGUAR X308 differential seal

                    Stabilizer Bar  Mount i
ng
 Frame  (64.25.12)  
                     Stabilizer Bar  Mounting  Frame  Bushing  (64.25.13)  
                     Rear Wheel  Bearing  (64.15.14)  
                     Wheel Hub  Seal  (64.15.15)  
                     Wheel Knuckle  Bushing (64.15.24)  
 
             204‐04:  Wheels  and Tires  
                 Specification  
                 Description  and  Operation  
                     Wheels and Tires  
                 Diagnosis  and  Testing  
                     Wheels and Tires  
                 Removal and  Installation  
                     Whee
l  and  Tire  (74.20.05)  
 
             204‐05:  Vehicle  Dynamic  Suspension 
                 Description  and  Operation  
                     Vehicle Dynamic  Suspension  
                 Diagnosis  and  Testing  
                     Vehicle Dynamic  Suspension  
 
        205:  Driveline  
 
             205‐00:  Driveline  System  ‐ General  Information  
                 Description  and  Operation  
                     Driveline System  
 
             205‐01:  Driveshaft  
                 Specification  
                 Description  and  Operation  
                     Drives
haft 
                 Removal and  Installation  
                     Driveshaft (47.15.01) 
 
             205‐02:  Rear  Drive  Axle/Differential  
                 Specification  
                 Description  and  Operation  

                    Rear Drive  Axle and  Diffe rential
 
                 General Procedures  
                     Differential  Output Shaft  End  Float  Check  (51.10.24)  
                 In‐Vehicle  Repair  
                     Axle Shaft  (47.10.01)  
                     Differential  Output Shaft  Bearing  (51.10.22)  
                     Drive Pinion  Flange  and  Drive  Pinion  Seal  (51.20.01)  
                 Removal and  Installation  
                     Axle Assembly  (51.25.13)  
 
        206:  Brake  System  
 
             206‐00:  Brake  System  ‐ Gen
eral Information 
                 Specification  
                 Description  and  Operation  
                     Brake System  
                 Diagnosis  and  Testing  
                     Brake System  
                 General Procedures  
                     Brake System  Bleeding  (70.25.03)  ‐ Vehicles  With: Standard  Brakes 
                     Brake System  Bleeding  (70.25.03)  ‐ Vehicles  With: High  Performance  Brakes  
                     Front Brake  Disc  Runout  Check ‐  Vehicles  With: Standard  Brakes  
                     Front Brake  Disc  Runout  Chec
k ‐ Vehicles  With: High Performance  Brakes 
                     Rear Brake  Disc  Runout  Check  (70.12.36)  ‐ Vehicles  With: Standard  Brakes 
                     Rear Brake  Disc  Runout  Check  (70.12.36)  ‐ Vehicles  With: High Performance   
            Brakes 
 
             206‐03:  Front  Disc Brake  
                 Specification  
                 Description  and  Operation  
                     Front Disc  Brake  
                 Removal and  Installation  
                     Brake Caliper  (70.55.02)  ‐ Vehicles  With: Standard  Brakes  
                     Brake Caliper  (70.55.02)  ‐ Vehicles  With: High  Perfo
rmance  Brakes  
                     Brake Disc  (70.10.10)  ‐ Vehicles  With: Standard  Brakes 
                     Brake Disc  (70.10.10)  ‐ Vehicles  With: High Performance  Brakes 
                     Brake Pads  (70.40.02)  ‐ Vehicles  With: Standard  Brakes 

Re
ar Drive Axle/Differential -
Lubric
ants, Fluids, Sealants and Adhesives
Capacities
Torques


UnitSp
ecification
F
i
nal Drive
Shell Sp
irax Supe
r TS 90
Hub s
p
line to Axle shaft
Loct
it
e 270 Studlock or equivalent
UnitLi
t
ers
F
i
nal Drive
1,
90
Com p
onent
Nm
B
ol
t - Final drive nose plate
39
- 51
Bol t
- 'A' frame to final drive
9
0 -
110
Nu
t 'A' f
rame to rear mounting bracket
8
5 -
115
Nu
t -
Axle shaft to final drive flange
81
-
99
Nu
t -
Axle shaft to hub
3
04 -
336
N
u
t - Damper lower fixing
8
0 -
100
Bol
t
M12 - Jurid flexible coupling to
transmission and final drive flanges
75 -
88
N
u
t - Lower fulcrum
9
0 -
110
Nu
t -
Pendulum to final drive
1
60 -
200
N
u
t - Stabilizer to wishbone
30
-
40
N
u
t - Tie rod to final drive
8
5 -
105
Nu
t -
Tie rod to wide mounting bracket
8
5 -
115
Nu
t -
Wishbone pivot
8
0 -
100
N
u
t - Wishbone tie to final drive
8
5 -
105
N
u
t 'A' frame to wide mounting bracket
8
5 -
105

R
ear Drive Axle/Differential - Rear Drive Axle and Differential
Description an
d Operation
Loca

tion
The differential
unit
is mounted between the wide mount ing bracket, pendulum assembly and the wishbone tie assembly.
Two tie rods are fitted between top rear of the final dr ive casing and the front of the wide mounting bracket.

Parts List
Description
The
type 14 HU final drive assembly is a hypoid unit with th
e pinion arranged on the cross-car centerline. The driveshaft
coupling utilizes a cassette type pinion oil seal, which is an in tegral part of the pinion flange. This type of seal cannot be
separated from the pinion fl ange and therefore may only be renewed as a complete seal / flange assembly
The axle shafts are driven by the output flanges which rotate on sealed bearings , these assemblies being retained in the
final drive unit by circlips.
Pinion Drive Flange / Seal Detail
• NOTE: The component parts are shown in an exploded view for clarity, this is NOT the fitted condition
It
em
Par
t Number
De
scription
1—F

inal Drive Unit
2—W

ide Mounting Bracket
3—Pen

dulum Assembly
4—Wi

shbone Tie Assembly
5—'A'

Frame

carri
er

7. Protect
the driveshaft thread wi
th special tool JD 1D / 7.

8. Wi
thdraw the hub from the axle shaft
8. CAUTION: Take care not to introduce debris into
the hub bearings, or damage the seal
U
sing service tool 204 - 011,
push the axle shaft through
the hub

9. NO
TE: In the wheel-free condition, the axle is in tension and
the flanges will separate as the nuts are withdrawn
Release the axle shaft 1. Remove and discard the (4) nuts axle shaft to differential output shaft
2. Clear the axle shaft from the output flange studs
3. Remove and keep safe the camber shim
10. NOTE: The axle shaft nuts may damage the studs upon
removal; check the thread conditio n by engaging a new nut 2 or 3
threads by hand.
Inspect the output flange studs and renew if there is evidence
of damage / distortion
11. Clean all traces of thread lo cking agent from the hub splines

R
ear Drive Axle/Differential - Drive Pinion Flange and Drive Pinion Seal
In-v
ehicle Repair
Remov

al
S
pecial Tool(s)

Drive sh

aft flange wrench
205-053

D
rive shaft flange remover replacer.

205-272

1. Di
sconnect the battery ground lead.
2. Raise the vehicle for access.

3. Disconnect the main parking br ake c
able at the compensator.
4. Release the parking brake relay lever mounting bracket and
allow the assembly to hang down.
R
emove the fixings (4).

5. Disconne
ct the driveshaft fr
om the differential flange.
5. CAUTION: Under no circumstances must the
flexible coupling (or its fixings) be loosened or removed
from the drive shaft.
1. 'Match mark' the FLEX IBLE COUPLING to the
differential DRIVE FLANGE.
2. Remove the fixings (3).
6. Support the d
riveshaft, do not allow it to hang.

7. Re
move the fixings (2) center
bearing to mounting bracket and
push the drive shaft rear sectio n forward to disengage from the
pinion spigot.

8. Remove the drive flange pinion nu
t.
1. Using a suitable tool, re lieve the staked portion from
the pinion keyway.
2. Remove the pinion nut using a suitable socket and tool 205 - 053 to resist rotation.
9. Remove the drive flange assembly.
1. Use tool 205-272 (puller) to remove the drive flange / seal assembly.

Sym
ptom #2
Sy
mptom #2
Sym

ptom #3
Sy
mptom #3
No
cooling
Compressor sei
zed
Compressor seal failure
Compressor valve or piston damage
*
*
*
R
enew compressor
*
Compressor cl
utch / circuit faulty
*
R
efer to PDU
*
D
rive belt slack / broken
*
Adjust or r
enew
*
B
lower motor / circuit faulty
Pressure switch / circuit fault
*
*
R
efer to PDU
*
Total l
oss of refrigerant caused by broken pipe or joint
*
Repair / renew. Check code 2
3
*
P
artial loss of refrigerant caused by leaking joint or pipe
*
R
epair / renew, check fault code #23
*
Conden
ser damage
*
Re
new, check fault code #23
*
Bl
ocked receiver / drier filter
*
R
enew receiver / drier
*
Evaporator senso
r / circuit faulty
*
R
efer to PDU, check fault code #13
*
Bl
ocked pollen filter (if fitted)
*
Cle
an or renew
*
• NOTE: Should a leak or low refrigerant be established as the cause of INSUFFICIENT COOL ING, follow the procedures
Recovery / Recycle / Recharge, this section, and ob serve all refrigerant and oil handling instructions.
Sy
mptom
Possib
le Sources
Acti
on
Insuffi

cient
cooling
Compre
ssor clutch slipping
*
R
enew clutch assembly
*
Fl
aps or vents closed / seized
*
Check f
ault codes #41 to 46
*
Bl
ower circuit fault
*
R
efer to PDU
*
Bl
ocked condenser matrix / fins
*
Check hig
h / low side pr
essures / renew. Check /
clean fins
*
Bl
ocked evaporator matrix
*
Check hig
h / low side
pressures / renew
*
Bl
ocked pollen filter (if fitted)
*
Cle
an or renew
*
Evaporator temp
erat
ure sensor faulty
*
R
efer to PDU
*
P
artial loss of refrigerant caused by leaking joint

or pipe
*
R
epair / renew
*
Blocked expan
sion valve
*
Check hig
h / low side
pressures / renew
*
Expans
ion valve fault
*
Chec
k system pres
sure differential
*
C
ollapsed air conditioning hose hose
*
Check hig
h / low side
pressures / renew
*
Moi
sture or air in the system
*
Chec
k system pressures
*
Low r
efrigerant charge
*
Initiate recovery
procedure, check fault code #23
*
Coo
lant flow valve open
*
Chec
k operation
*
Sy
mptom
Possib
le Sources
Acti
on
Int

ermittent cooling
Compre
ssor clutch slipping
*
R
enew clutch assembly
*
Compressor cl
utch circuit faulty
Blower(s) circuit faulty
*
*
R
efer to PDU
*
Motorized in-car aspirator faulty

*
R
efer to PDU, check fault code #11
*
Evaporator temp
erature sensor faulty

*
R
efer to PDU, check fault code #13
*
Bl
ocked condenser matrix / fins
*
Check hig
h / low side pressures / renew. Check / clean fins

*
Bl
ocked evaporator matrix
*
Check hig
h / low side
pressures / renew
*


Sym
ptom #1
Sy
mptom #1
Sy

mptom
Possib
le Sources
Acti
on