1998 JAGUAR X308 Seat

Installation

6.
Slacken and remove screws securing hinge to lid and remove
hinge.
1. Position hinge on console lid and fit and tighten securing
screws.
2. Position glovebox lid on cent re comsole and fit and tighten
securing screw.
3. Fully seat liner in centre co nsole and fit and tighten rear
securing screws.
4. Fit glovebox latch to liner and fit and tighten securing screws.
5. Position glovebox to lid stay, fi t and tighten securing screw and
close glovebox lid.

Instrument Panel and Console - Glove Compartment
Removal and Installation
Removal
Installation

1.
Open glovebox.

2. Supporting the glovebox, slac ken and remove the four top
securing screws.

3. Slacken and remove the two glovebox lower outer securing
screws.

4. Withdraw glovebox for access and disconnect the two
illumination harness connectors.
5. Remove glovebox from vehicle.
1. Position glovebox for access and connect illumination harness.
2. Position and fully seat glovebox.
3. Fit but do not tighten the lower securing screws.
4. Fit and fully tighten the upper securing screws.
5. Close glovebox lid.
6. Fully tighten the lower securing screws.

Instrument Panel and Console - Glove Compartment Liner
Removal and Installation
Removal
Installation

1.
Remove glovebox refer to 76.52.03.
2. Remove glovebox lid. Tefer to 76.52.02.
3. Remove glovebox damper. Refer to 76.52.22.

4. Release damper cord guide retaining tangs and remove guide
from bracket.

5. Position liner for access and ca refully remove switch assembly
from housing.
1. Route illumination switch harness into switch housing.
2. Connect switch to harness mult iplugs and fit and fully seat
switch in housing.
3. Secure harness in liner clips.
4. Fit lid damper to liner. Refer to 76.52.22.
5. Fit damper cord guide to bracket.
6. Route damper cord through guide and connect to damper.
7. Fit glovebox lid. refer to 76.52.02.
8. Fit glovebox. Refer to 76.52.03.

Instrument Panel and Console - Instrument Cluster Finish Panel
Removal and Installation
Removal
Installation

1.
Turn ignition key to position II.
2. Move steering column to lowest and fully extended position.
3. Turn ignition key to position 'O'.
4. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.15.

5. Release veneer panel from retaining clips.
6. Remove veneer panel from vehicle.
7. Remove and discard all retaining clips.
1. Fit new retaining clips to instrument surround.
2. Fit and fully seat veneer pa nel to instrument surround.
3. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.
4. Turn ignition key to position II.
5. Return steering column to original position.
6. Turn ignition key to position 'O'.

Installation




8. Slacken and remove four screws securing major gauge
module/surround to fascia and withdraw surround.
1. Position major gauge surround on panel, routing harness
multiplugs through apertures.
2. Fit and tighten screws securing major gauge module/surround
to fascia.
3. Connect harness multiplug to tr ip keyboard and fit and fully
seat keyboard in gauge surround, ensuring correct location of
retaining tangs
4. Connect harness multiplug to fog lamp switch and fit and fully
seat switch in gaug e surround, ensuring correct location of
tangs.
5. Fit veneer panel. Refer to 76.47.24.
6. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.
7. Return steering column to original position.

Instrument Panel and Console - Instrument Panel
Removal and Installation
Removal
1. Turn ignition switch to position II.
2. Motor driver and front passenger seats rearward.
3. Position steering wheel in stra ight ahead position and fully
lower and extend steering column.
4. Turn ignition switch to position O.
5. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
6. Remove 'J' gate finish er. Refer to 76.25.24.
7. Remove 'J' gate finisher retain ing panel. Refer to 76.25.26.
8. Remove centre console veneer panel. Refer to 76.47.26.
9. Disconnect and remove radio.
10. Remove centre console switch module. Refer to 86.80.32.
11. Remove centre console. Refer to 76.25.01.

12. Slacken and remove centre cons ole vent duct rear securing
screw and withdraw duct assemb ly from air conditioning unit
manifold.
13. WARNING: BEFORE ANY AIRBAG/SRS SERVICE IS
PERFORMED, AT LEAST ONE MINUTE MUST ELAPSE AFTER
DISCONNECTION OF THE BATTERY CABLE, TO ALLOW
DISSIPATION OF BACK-UP POWER SUPPLY ENERGY.
Remove driver airbag. Refer to 76.73.39.
14. Remove steering wheel. Refer to Section 211-04.
15. Remove steering column lo wer cowl. Refer to 76.46.03.
16. Remove steering column u pper cowl. Refer to 76.46.02.
17. Remove driver side unders cuttle. Refer to 76.46.11.
18. Remove combined windshield wiper/washer switch and
audible warning speaker assembly. Refer to 86.65.42.
19. Remove glovebox. Refer to 76.52.03.
20. Remove 'A' post lower trim pads. refer to 76.13.30.
21. Carefully withdraw driver stowage bin trim, remove bin
securing screw and remove bin from facia.

9. Fully seat air distribution bo x and install securing nuts.

10. Install LH and RH air distributi on box/facia side vent ducts
and install securing screws.
11. Install LH and RH top vents on facia.
12. Install all defrost vent retaining clips to facia.
13. Install LH and RH windshield defrost vents to facia

14. Position centre defro st vent/solar sensor assembly, connect
sensor harness multiplug to facia harness, install multiplug on
retaining clip and fully seat assembly in facia.
15. Reposition facia right way up on bench.
16. Position face level air ducts in facia and install securing
screws.

23. WARNING: ENSURE THAT THE AIR BAG AND
RETAINING CLIPS ARE FULLY SEATED.
Install deployment door.
Install and fully seat deployment door retaining clips in
facia.
Install and fully seat deployment door in clips.

24. Position trunk release switch/housing at facia and connect in-
car sensor to housing.

25. Connect trunk release switch multiplug to facia harness and
install in-car sensor/trunk release switch assembly to facia.
26. Install new major gauge module retaining screw inserts to
facia.
27. Install major gauge module in facia. Refer to 88.20.24.
28. Install instrument panel veneer panel. Refer to 76.47.24.
29. Reposition facia on bench wi th back facing outwards.
30. Position body processor module in facia and install securing
nuts.