1996 TOYOTA LAND CRUISER Washer

R05748
L
M
R05749
2 Times or more
R05751
−
SUPPLEMENTAL RESTRAINT SYSTEM STEERING WHEEL PAD AND SPIRAL CABLE
RS−15
1996 LAND CRUISER (RM451U)
(1) Install the 2 bolts with washers in the 2 bolt holes in
the steering wheel pad.
Bolt:
L: 35. mm (1.387 in.)
M: 6.0 mm (0.236 in.)
Pitch: 1.0 mm (0.039 in.)
NOTICE:
Tighten the bolts by hand until the bolts become diffi-
cult to turn.
Do not tighten the bolts too much.
(2) Using 3 wire harnesses, wind the wire harness at least 2 times each around the bolts installed on the
left and right sides of the steering wheel pad.
CAUTION:
Tightly wind the wire harness around the bolts so that
there is no slack.
If there is slack in the wire harness, the steering wheel
pad may come loose due to the shock when the air-
bag is deployed. This is highly dangerous.
(3) Face the upper surface of the steering wheel pad
upward. Separately tie the left and right sides of the
steering wheel pad to the disc wheel through the
hub nut holes. Position the steering wheel pad con-
nector so that it hangs downward through a hub
hole in the disc wheel.
CAUTION:
Make sure that the wire harness is tight. It is very dan-
gerous when looseness in the wire harness results in
the steering wheel pad coming free through the shock
from the airbag deploying.
Always tie down the steering wheel pad with the pad
side facing upward. It is very dangerous if the steer-
ing wheel pad is tied down with the metal surface fac-
ing upward as the wire harness will be cut by the
shock from the airbag deploying and the steering
wheel pad will be thrown into the air.
NOTICE:
The disc wheel will be marked by airbag deployment, so
when disposing of the airbag use a redundant disc wheel.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UB−01
SA2635
SST
−
SUSPENSION AND AXLE FRONT AXLE HUB
SA−7
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT WHEEL
2. REMOVE BRAKE CALIPER (See page BR−25 )
3. REMOVE FLANGE
(a) Using a screwdriver and hammer, remove the grease cap
from the flange.
(b) Using a snap ring expander, remove the snap ring.
(c) Loosen the 6 mounting nuts.
(d) Using a brass bar and hammer, tap on the 6 bolts heads and remove the 6 cone washers, plate washers and nuts.
(e) Remove the flange.
(f) Remove the gasket.
4. REMOVE AXLE HUB WITH DISC
(a) Using a screwdriver, release the lock washer.
(b) Using SST, remove the lock nut. SST 09607−60020
(c) Remove the lock washer.
(d) Using SST, remove the adjusting nut and thrust washer.
SST 09607−60020
(e) Remove the hub and disc together with the outer bearing.
5. REMOVE OIL SEAL AND INNER BEARING
(a) Using SST, remove the oil seal. SST 09308−00010
(b) Remove the inner bearing from the hub.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UB−01
SA2635
SST
−
SUSPENSION AND AXLE FRONT AXLE HUB
SA−7
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT WHEEL
2. REMOVE BRAKE CALIPER (See page BR−25 )
3. REMOVE FLANGE
(a) Using a screwdriver and hammer, remove the grease cap
from the flange.
(b) Using a snap ring expander, remove the snap ring.
(c) Loosen the 6 mounting nuts.
(d) Using a brass bar and hammer, tap on the 6 bolts heads and remove the 6 cone washers, plate washers and nuts.
(e) Remove the flange.
(f) Remove the gasket.
4. REMOVE AXLE HUB WITH DISC
(a) Using a screwdriver, release the lock washer.
(b) Using SST, remove the lock nut. SST 09607−60020
(c) Remove the lock washer.
(d) Using SST, remove the adjusting nut and thrust washer.
SST 09607−60020
(e) Remove the hub and disc together with the outer bearing.
5. REMOVE OIL SEAL AND INNER BEARING
(a) Using SST, remove the oil seal. SST 09308−00010
(b) Remove the inner bearing from the hub.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UD−01
SA2636
Grease
R04134
SST
−
SUSPENSION AND AXLE FRONT AXLE HUB
SA−9
1996 LAND CRUISER (RM451U)
INSTALLATION
1. PACK BEARINGS WITH MP GREASE
(a) Place MP grease on the palm of your hand.
(b) Pack grease into the bearing until the grease oozes out
from the other side.
(c) Do the same around the bearing circumference.
2. COAT INSIDE OF HUB WITH MP GREASE
3. INSTALL INNER BEARING AND OIL SEAL
(a) Place the inner bearing into the hub.
(b) Using SST, install a new oil seal into the hub. SST 09950−60020 (09951 −00910),
09950 −70010 (09951 −07150)
(c) Coat the oil seal lip with MP grease.
4. INSTALL AXLE HUB WITH DISC TO SPINDLE
(a) Place the axle hub with disc to the spindle.
(b) Install the outer bearing.
(c) Install the thrust washer.
5. ADJUST PRELOAD
(a) Using SST, torque the adjusting nut.
SST 09607−60020
Torque: 59 N·m (600 kgf·cm, 43 ft·lbf)
(b) Turn the hub right and left 2 or 3 times.
(c) Using SST, torque the adjusting nut.
SST 09607−60020
Torque: 59 N·m (600 kgf·cm, 43 ft·lbf)
(d) Loosen the nut until it can be turned by hand.
(e) Using SST, torque the adjusting nut again.
SST 09607−60020
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
NOTICE:
Check that the bearing has no play.
(f) Using a spring tension gauge, measure the preload.
Preload (at starting):
28 − 56 N (2.9 − 5.7 kgf, 6.4 − 12.6 lbf)
6. INSTALL LOCK WASHER AND LOCK NUT
(a) Install a new lock washer and lock nut.
(b) Using SST, torque the lock nut. SST 09607−60020
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
(c) Check that axle hub turns smoothly and that the bearing has no play.
(d) Using a spring tension gauge, check the preload. Preload (at starting):
28−56 N (2.9−5.7 kgf, 6.4−12.6 lbf)
If it is not within the specification, adjust it with the adjusting nut
after removing the lock washer and lock nut.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R08416
SA−10
−
SUSPENSION AND AXLE FRONT AXLE HUB
1996 LAND CRUISER (RM451U)
(e) Secure the lock nut by bending one of the lock washer
teeth inward and the other lock washer teeth outward.
7. INSTALL FLANGE
(a) Place a new gasket in position on the axle hub.
(b) Apply MP grease to the inner flange splines.
(c) Install the flange to the axle hub.
(d) Install the 6 cone washers, plate washers and nuts.
(e) Torque the 6 nuts.
Torque: 35 N·m (360 kgf·cm, 26 ft·lbf)
(f) Install the bolt in the axle shaft and pull it out.
(g) Using a snap ring expander, install a new snap ring.
(h) Remove the bolt.
(i) Coat inside of the cap with MP grease.
(j) Install the cap to the flange.
8. INSTALL BRAKE CALIPER (See page BR−29 )
9. INSTALL FRONT WHEEL Torque:
Steel wheel: 147 N·m (1,500 kgf·cm, 109 ft·lbf)
Alumimum wheel: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
10. BLEED BRAKE LINE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UG−01
W00495
SA2644
SST
R08383
R13137
−
SUSPENSION AND AXLE STEERING KNUCKLE AND AXLE SHAFT
SA−13
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT AXLE HUB (See page SA−7 )
2. REMOVE ABS SPEED SENSOR
Remove the 2 bolts and disconnect the speed sensor from the
steering knuckle.
3. REMOVE DUST SEAL AND DUST COVER
Remove the 8 bolts, dust seal, dust cover and gasket.
4. REMOVE KNUCKLE SPINDLE
(a) Using a brass bar and hammer, tap the knuckle spindle of the steering knuckle.
(b) Remove the knuckle spindle and gasket.
5. REMOVE AXLE SHAFT
Position one flat part of the outer shaft upward and remove the
axle shaft.
6. DISCONNECT TIE ROD FROM KNUCKLE ARM
(a) Remove the cotter pin and nut.
(b) Using SST, disconnect the tie rod from the knuckle arm. SST 09611 −22012
7. REMOVE OIL SEAL SET
(a) Remove the 6 bolts from the end retainer.
(b) Remove these parts from the steering knuckle:
Oil seal end retainer
Felt dust seal
Rubber seal
Steel ring
8. REMOVE KNUCKLE ARM AND BEARING CAP
(a) Remove the 2 bolts and plate washers from the bearing cap.
(b) Remove the 4 nuts from the knuckle arm.
(c) Using a brass bar and hammer, tap on the 4 bolts heads and remove the 4 cone washers.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UI−01
SA2650
SST
Z15221
Lithium Base Wheel Bearing
Grease, NIGI No.2
R08387SST
R08388
SST
−
SUSPENSION AND AXLE STEERING KNUCKLE AND AXLE SHAFT
SA−17
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL OIL SEAL TO AXLE HOUSING
Using SST and a hammer, install a new oil seal into the axle
housing.
SST 09618−60010
2. INSTALL OIL SEAL SET
Install these parts to the steering knuckle:
Oil seal and retainer
Felt dust seal
Rubber seal and steel ring
3. PACK BEARINGS WITH LITHIUM BASE WHEEL
BEARING GREASE, NLGI NO.2
(a) Place lithium base wheel bearing grease, NLGI No.2 on your hand.
(b) Pack grease into the bearing until the grease oozes out from the outer side.
(c) Do the same around the bearing circumference.
4. INSTALL STEERING KNUCKLE AND BEARINGS
(a) Place the bearings in positions on the knuckle and axle housing.
(b) Install the knuckle on the axle housing.
5. INSTALL KNUCKLE ARM AND BEARING CAP
(a) Using SST, support the upper bearing inner race. SST 09606−60020
HINT:
Use the SST with a collar.
(b) Install the bearing cap over the shim that were originally
used.
(c) Using a hammer, install the bearing cap into the bearing
inner race.
(d) Using SST, support the lower bearing inner race. SST 09606−60020
HINT:
Use the SST with a collar.
(e) Using a hammer, tap the knuckle arm and shim into the
bearing inner race.
(f) Remove the SST from the knuckle.
(g) Install the 4 cone washers and nuts.
Torque: 96 N·m (980 kgf·cm, 71 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13138
90°
Z15222
Molybdenum
Disulfide
Lithium
Base Grease
NIGI No.2
SA−18
−
SUSPENSION AND AXLE STEERING KNUCKLE AND AXLE SHAFT
1996 LAND CRUISER (RM451U)
(h) Install the 2 plate washers and bolts.
Torque: 96 N·m (980 kgf·cm, 71 ft·lbf)
6. MEASURE BEARINGS PRELOAD
Using a spring tension gauge, measure the preload. Preload (at starting):
25 − 44 N (2.5 − 4.5 kgf, 5.6 − 9.9 lbf)
7. ADJUST BEARING PRELOAD
(a) Remove the bearing cap and knuckle arm (See page SA−13 ).
(b) Select the adjusting shim. Adjusting shim thickness
Thickness mm (in.)Thickness mm (in.)
0.1 (0.004)0.5 (0.020)
0.2 (0.008)1.0 (0.039)
(c) Install the bearing cap and knuckle arm (See page SA−17 ).
8. CONNECT TIE ROD TO KNUCKLE ARM
Torque the nut and secure it with a new cotter pin. Torque: 91 N·m (925 kgf·cm, 67 ft·lbf)
9. INSTALL OIL SEAL END RETAINER TO KNUCKLE ARM
Install the oil seal end retainer to steering knuckle with the 6
bolts. Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
10. INSTALL AXLE SHAFT
Position one flat part of the outer shaft upward and install the
shaft.
11. PACK MOLYBDENUM DISULFIDE LITHIUM BASE GREASE, NLGI NO.2
Pack molybdenum disulfide lithium base grease, NLGI No.2
into the knuckle to about 3 fourths of the knuckle.
12. INSTALL KNUCKLE SPINDLE, DUST COVER WITH
GASKETS AND DUST SEAL
(a) Place a new gasket in the position on the knuckle and
install the spindle.
(b) Place the dust cover, dust seal and a new gasket on the spindle.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010