1996 TOYOTA LAND CRUISER Washer

BO385−01
−
BODY REAR WIPER AND WASHER
BO−31
1265
Author: Date:
1996 LAND CRUISER (RM451U)
REAR WIPER AND WASHER
REMOVAL
1. REMOVE PULL HANDLE AND PULL HANDLE BEZEL
2. REMOVE BACK DOOR TRIM
(a) Insert a screwdriver between the retainers and door trim
to pry it loose.
HINT:
Tape the screwdriver tip before use.
(b) Remove the back door trim.
3. REMOVE WIPER ARM, MOTOR AND REAR WIPER CONTROL RELAY
(a) Open the cap.
(b) Remove the nut and wiper arm.
(c) Remove the 5 bolts and motor, then disconnect the con- nector.
(d) Remove the bolts and rear wiper control relay,then dis- connect the connector.
4. ADJUST REAR WASHER NOZZLE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO386−01
BO−32
−
BODY REAR WIPER AND WASHER
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT REAR WASHER NOZZLE
While operating the washer, check whether the point where the
washer fluid hits the back door glass and the upsurge area are
within the range indicated by the hatched line.
AApprox. 120 mm (4.72 in.)
BApprox. 120 mm (4.72 in.)
CApprox. 90 mm (3.54 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO387−01
−
BODY REAR WIPER AND WASHER
BO−33
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL WIPER CONTROL RELAY
2. INSTALL WIPER MOTOR
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
3. INSTALL BACK DOOR TRIM
4. INSTALL PULL HANDLE BEZEL
5. INSTALL PULL HANDLE
6. INSTALL REAR WIPER ARM
(a) Install the wiper arm and operate the wipers once and turn
the wiper switch OFF.
(b) Adjust the installation positions of the wiper arm to the positions shown in the illustration.
A: Approx. 40 mm (1.57 in.)
(c) Tighten the nut. Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO4047
Point Marks
BO−66
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
33. ADJUST DRIVE RAIL
HINT:
Adjust the drive rail to a closed and tilted down position.
Using a screwdriver, slide the link forward or backward to align
the 2 marks, as shown.
34. ADJUST AND INSTALL DRIVE GEAR ASSEMBLY
(a) Remove the screw and cam plate cover.
(b) Remove the large screw, washers and shims.
(c) Turn the drive shaft by screwdriver to align the housing
and gear point mark, as shown.
(d) Install the cam plate cover with the screw.
(e) Install the drive gear assembly with 4 bolts.
(f) Connect the connector.
35. INSTALL DRIVE GEAR CONTROL RELAY AND BRACKET
(a) Install the bracket with 2 bolts.
(b) Install the drive gear control relay with the bolt, then con-
nect the connector.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO5152
BO391−01
BO−68
−
BODY SLIDING ROOF
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SLIDING ROOF GLASS ALIGNMENT
(a) Start the engine and check the operation time of the slid-
ing roof.
Operation time: Approx. 5 sec.
(b) Check for abnormal noise or binding during operation.
(c) With the sliding roof fully closed, check for water leakage.
(d) Check for a difference in level between the sliding roof weatherstrip and roof panel.
Front End0.9 − 3.9 mm (0.035 − 0.154 in.)
Rear End0.9 − 3.9 mm (0.035 − 0.154 in.)
2. If the sliding roof does not operate:
ADJUST SLIDING ROOF GLASS ALIGNMENT
(a) Remove the control switch cover.
(b) Remove the large screw inside.
NOTICE:
Be careful not to lose the spring washer or shim.
(c) Manually operate the moon roof by inserting a special
crank−shaped screwdriver into the hole and turning the
drive shaft.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO48R−01
BO−84
−
BODY FRONT SEAT (Power Adjuster Type)
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE FRONT SEAT HEADREST
2. REMOVE SIDE SUPPORT ADJUSTER KNOB
Using a screwdriver, remove the snap ring and side support ad-
juster knob.
3. REMOVE SEATBACK BOARD
(a) Remove the 2 screws.
(b) Slide the board downward to remove it.
4. REMOVE FRONT SEATBACK ASSEMBLY
(a) Using a hog ring pliers, remove the hog ring backward of seatback.
(b) Remove the 4 bolts and front seatback assembly. Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
5. REMOVE FRONT SEAT CUSHION INNER SHIELD
6. REMOVE FRONT SEAT INNER BELT
7. REMOVE FRONT SEAT CUSHION SHIELD
8. REMOVE FRONT SEAT CUSHION
(a) Remove the 4 bolts.
Torque: 30 N·m (300 kgf·cm, 22 ft·lbf)
(b) Disconnect the connector, then remove the front seat cushion.
9. REMOVE SEAT CUSHION REAR PROTECTOR
10. REMOVE RECLINING ADJUSTER INSIDE COVER
Remove the 4 screws and reclining adjuster inside cover LH
and RH.
11. REMOVE POWER ADJUST FRONT SHIELD
Remove the 2 screws and front shield.
12. REMOVE SLIDE MOTOR
(a) Using the 5.0 mm (0.20 in.) hexagon wrench, remove the
4 housing bracket screws.
Torque: 10 N·m (100 kgf·cm, 7.0 ft·lbf)
(b) Hold the front seat horizontal jack screw with a plier, and remove the 2 nuts and 2 washers.
Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)
HINT:
At the time of installation, apply adhesive to nut. Part No. 08833 − 00070, THREE BOND 1324 or equiva-
lent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY FRONT SEAT (Power Adjuster Type)
BO−85
1996 LAND CRUISER (RM451U)
(c) Remove the 4 screws and 2 vertical adjuster bushes.
(d) Remove the 4 bolts, slide motor, front seat slide housing
and front seat horizontal jack screw.
Torque: 19 N·m (200 kgf·cm, 14 ft·lbf)
(e) Loosen the seat adjuster nut, then remove the slide mo- tor.
13. REMOVE REAR VERTICAL MOTOR
(a) Remove the 2 E −rings, and disconnect the No. 1 vertical
seat link.
(b) Remove the 4 bolts, vertical rod hold bracket RH and ver-
tical rod hold bracket LH.
Torque: 20 N·m (210 kgf·cm, 15 ft·lbf)
(c) Using the 5.0 mm (0.20 in.) hexagon wrench, remove the
2 housing support bracket screws.
Torque: 10 N·m (100 kgf·cm, 7.0 ft·lbf)
(d) Hold the No. 2 vertical travel jack screw with a plier, re- move the nut and washer.
Torque: 2.0 N·m (20 kgf·cm, 17 in.·lbf)
HINT:
At the time of reassembly, apply adhesive to nut.
Part No. 08833− 00070, THREE BOND 1324 or equiva-
lent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−86
−
BODY FRONT SEAT (Power Adjuster Type)
1996 LAND CRUISER (RM451U)
(e) Remove the 2 screws, vertical adjuster bush, rear vertical
motor and No. 2 vertical seat link.
14. REMOVE FRONT VERTICAL MOTOR
(a) Using the 5.0 mm (0.20 in.) hexagon wrench, and remove
the 2 housing support bracket screws.
Torque: 10 N·m (100 kgf·cm, 7.0 ft·lbf)
(b) Hold the No. 1 vertical travel jack screw with a plier, re- move the nut and washer.
HINT:
At the time of reassembly, apply adhesive to nut. Part No. 08833− 00070, THREE BOND 1324 or equiva-
lent
Torque: 2.0 N·m (20 kgf·cm, 15 ft·lbf)
(c) Remove the 2 screws, vertical adjuster bush, front vertical
motor and No. 1 vertical seat link.
15. REMOVE FRONT SEAT TRACK
(a) Remove the 2 bolts and front seat motor side housing. Torque: 20 N·m (210 kgf·cm, 15 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010