1996 TOYOTA LAND CRUISER boot

IN00U−36
N17080
Filler Cap
Float
Reservoir Grommet
Clip
Slotted Spring Pin
: Specified torque
 Non− reusable partCylinder
Piston
Push Rod
Washer
Snap Ring
Boot

Gasket
Lock Nut
Clevis Pin
Clevis
N·m (kgf·cm, ft·lbf)
12 (120, 9)
15 (155, 11)
−
INTRODUCTION HOW TO USE THIS MANUAL
IN−1
1
Author: Date:
1996 LAND CRUISER (RM451U)
HOW TO USE THIS MANUAL
GENERAL INFORMATION
1. INDEX
An INDEX is provided on the first page of each section to guide you to the item to be repaired. To assist you
in finding your way through the manual, the section title and major headin\
g are given at the top of every page.
2. PRECAUTION
At the beginning of each section, a PRECAUTION is given that pertains to al\
l repair operations contained
in that section.
Read these precautions before starting any repair task.
3. TROUBLESHOOTING
TROUBLESHOOTING tables are included for each system to help you diagnose\
the problem and find the
cause. The fundamentals of how to proceed with troubleshooting are described o\
n page IN−18.
Be sure to read this before performing troubleshooting.
4. PREPARATION
Preparation lists the SST (Special Service Tools), recommended tools, equipment, lubricant and SSM (Spe-
cial Service Materials) which should be prepared before beginning the o\
peration and explains the purpose
of each one.
5. REPAIR PROCEDURES
Most repair operations begin with an overview illustration. It identifies the components and shows how the
parts fit together.
Example:
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08467
Rear Propeller
ShaftTransfer Shift
Lever Boot
Transmission Shif
Lever Assembly
Rear Console Box
Front Console Box
Engine Rear Mounting
Plug for Hydraulic Test
Oil Cooler Pipe Transfer Shift
Control Link
Transfer Shift
Lever Cushion
x 6
x 6 Clip
Transfer Shift
Lever Knob
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−19
803
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−21
1996 LAND CRUISER (RM451U)
(c) Remove the transfer shift lever knob.
(d) Remove the 4 screws and console.
(e) Remove the 4 screws and transfer shift lever boot.
(f) Remove the 3 bolts and console box.
(g) Disconnect the 3 connectors.
(h) Remove the 6 screws and transmission shift lever assem-
bly.
Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1CV−04
BR2008
Z09007
170 mm
(6.70 in.)50 mm
(1.97
in.)
16 mm
(0.63 in.)
BR0213
BR2009
BR−26
−
BRAKE FRONT BRAKE CALIPER
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE CYLINDER BOOT SET RINGS AND BOOTS
Using a screwdriver, remove the 4 cylinder boot set rings and
boots.
2. REMOVE PISTONS FROM CYLINDER
(a) Prepare the wooden plate to hold the pistons.
(b) Place the plate between the pistons and insert a pad at
one side.
(c) Use compressed air to remove the pistons alternately from the cylinder.
CAUTION:
Do not place your fingers in front of the pistons when using
compressed air.
3. REMOVE PISTON SEALS
Using a screwdriver, remove the 4 piston seals from the cylin-
der.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR−32
−
BRAKE REAR BRAKE PAD
1996 LAND CRUISER (RM451U)
(a) Install pad wear indicator plate to each pads.
(b) Install the anti−squeal shim to the outer pad.
(c) Install the 2 pads so the wear indicator plate is facing up-
ward.
NOTICE:
Do not allow oil or grease to get on the rubbing face.
8. INSTALL CALIPER
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in piston with a hammer handle or an equivalent.
HINT:
Always change the pads on one wheel at a time as there is a
possibility of the opposite piston flying out.
(c) Install the caliper carefully so the boot is not wedged.
(d) Install and torque the sliding main pin and sub pin. Torque: 88 N·m (900 kgf·cm, 65 ft·lbf)
9. INSTALL REAR WHEEL
10. CHECK THAT FLUID LEVEL IS AT MAX LINE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1D3−01
−
BRAKE REAR BRAKE CALIPER
BR−35
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE CYLINDER BOOT
Using a screwdriver, remove the cylinder boot from the caliper.
2. REMOVE PISTON
(a) Place a piece of cloth or similar article between the piston
and the caliper.
(b) Use compressed air to remove the piston from the cylin- der.
CAUTION:
Do not place your fingers in front of the piston when using
compressed air.
3. REMOVE PISTON SEAL
Using a screwdriver, remove the piston seal from the cylinder.
4. REMOVE DUST BOOT AND SLIDING BUSHING
Using a screwdriver and hammer, tap out dust boot and sliding
bushing.
HINT:
Tape the screwdriver tip before use.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BRAKE PARKING BRAKE
BR−41
1996 LAND CRUISER (RM451U)
7. REMOVE REAR SHOE, ADJUSTER AND TENSION
SPRING
(a) Slide out the rear shoe, and remove the rear shoe and ad-
juster.
(b) Remove the 2 shoe hold −down spring cups, spring and
pin.
(c) Remove the lower side tension spring.
8. REMOVE FRONT SHOE
(a) Slide out the front shoe.
(b) Remove the shoe 2 hold −down spring cups, springs and
pin.
(c) Disconnect the parking brake cable from the parking
brake shoe lever.
9. IF NECESSARY, REMOVE AND DISASSEMBLE PARKING BRAKE BELLCRANK ASSEMBLY
(a) Using a screwdriver, remove the C −washer.
(b) Remove the pin and disconnect the parking brake cable No.2 from the bellcrank.
(c) Remove the clip.
(d) Remove the pin and clip, then disconnect the parking
brake cable.
(e) Remove the 2 tension springs.
(f) Remove the 2 bolts and parking brake bellcrank assem- bly.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(g) Remove the boot from parking brake bellcrank bracket.
(h) Using a screwdriver, remove the C −washer and pin.
(i) Remove the parking brake bellcrank from the bell crank bracket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1DE−01
−
BRAKE LOAD SENSING PROPORTIONING AND BY− PASS
VALVE (LSP & BV)BR−49
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE VALVE BRACKET
(a) Remove the nut, bolt and 2 plate washers.
(b) Remove the 2 nuts, bracket and set plate from the valve
body.
2. DISCONNECT SPRING FROM VALVE
Using pliers, remove the clip, and remove the spring from the
valve.
3. REMOVE SHACKLE NO.1 AND NO.2
(a) Remove the bolt and nut, then remove the these parts:
Load sensing spring
2 plate washers
(b) Loosen the 2 nuts, and remove the shackle No.1 from the
shackle No.2.
4. DISASSEMBLE LOAD SENSING SPRING
Disassembly the these parts:
4 bushings
2 collars
2 rubber plates
Load sensing valve boot
Load sensing spring boot
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010