1996 TOYOTA LAND CRUISER bumper

BO37H−01
BO−4
−
BODY FRONT BUMPER
1238
Author: Date:
1996 LAND CRUISER (RM451U)
FRONT BUMPER
COMPONENTS
CAUTION:
The side rail extensions are necessary for normal function-
ing of the SRS airbag, so make sure that they are correctly
installed.When replacing the bumper, always inspect the
side rail extensions. If they are deformed or cracked, re-
place them. Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO37I−01
−
BODY REAR BUMPER
BO−5
1239
Author: Date:
1996 LAND CRUISER (RM451U)
REAR BUMPER
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO48P−01
N14081
N14075
BO−38
−
BODY WHEEL OPENING MOULDING
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE FRONT FENDER WHEEL OPENING MOULDING
(a) Remove the charcoal canister.
(b) Remove the air cleaner case assembly.
(c) Remove the cool air intake duct.
(d) Remove the front wheel.
(e) Remove the front mudguard.
(f) Remove the front bumper extension.
(g) Remove the 4 nuts from engine room inside service hole.
(h) Remove the 2 screws.
(i) Remove the front wheel opening extension.
2. REAR DOOR SIDE: REMOVE REAR WHEEL OPENING MOULDING
Remove the 2 bolts and moulding.
3. REMOVE REAR WHEEL OPENING MOULDING
(a) Remove the mud guard, bumper extention and back door
scuff plate.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO48Q−01
N14082
BO−40
−
BODY WHEEL OPENING MOULDING
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL FRONT WHEEL OPENING MOULDING
(a) Install the front wheel opening moulding.
(b) Install the 4 nuts from the service hole of the engine room
inside.
(c) Install the 2 screws.
(d) Front bumper extension
(e) Front mudguard
(f) Front wheel
(g) Cool air intake duct
(h) Air cleaner case assembly
(i) Charcoal canister
2. INSTALL QUARTER OUTSIDE MOULDING
Install the quarter outside moulding with the 2 bolts.
3. INSTALL REAR WHEEL OPENING MOULDING
(a) Install the rear wheel opening moulding with the 2 nuts.
(b) Install the screw.
(c) Install the quarter trim LH.
(d) Install the quarter trim RH.
(e) Install the back door scuff plate.
(f) Install the rear bumper extension.
(g) Install the rear mudguard.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1U9−02
Z03382
SA3213
AB
D
C
Front
R05628
A
B
A = B
SA−4
−
SUSPENSION AND AXLE FRONT WHEEL ALIGNMENT
861
Author: Date:
1996 LAND CRUISER (RM451U)
FRONT WHEEL ALIGNMENT
INSPECTION
1. MEASURE VEHICLE HEIGHT
Clearance:
A (Follow spring clearance): 36 mm (1.42 in.)
B (Bumper stopper clearance): 104 mm (4.09 in.)
If the clearance of the vehicle is not standard, try to level the ve-
hicle by rocking it down.
If still not correct, check for bad springs or suspension parts.
2. INSTALL CAMBER−CASTER−KINGPIN GAUGE OR ONTO WHEEL ALIGNMENT TESTER
Follow the specific instructions of the equipment manufacturer.
3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
Camber
Left−right error1°00’ ± 45
45’ or less
Caster Left−right error3°00’ ± 1°
45’ or less
Steering axis inclination13 °00’ ± 45’
Camber, caster and steering axis inclination are not adjustable.
If measurements are not within the specification, inspect the
suspension parts for damaged and/or worn out parts and re-
place them as necessary.
4. INSPECT TOE −IN
To e−in
(total)A+B: 0.2 ° ± 0.2°
C −D: 2 ± 2 mm (0.08 ± 0.08 in.)
If toe− in is not within the specification, adjust by the tie rod end.
5. ADJUST TOE−IN
(a) Loosen the clamp bolts and nuts.
(b) Adjust toe−in to the correct value by turning the tie rod.
HINT:
Make sure that the lengths of the left and right tie rod ends are
the same.
(c) Torque the clamp bolts and nuts. Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EC−02
SS−30
−
SERVICE SPECIFICATIONS SUSPENSION AND AXLE
153
Author: Date:
1996 LAND CRUISER (RM451U)
SUSPENSION AND AXLE
SERVICE DATA
Cold tire inflation
pressureTire size
P275/70R 16
220 kPa (2.2 kgf/cm2, 32 psi)
Follow spring and
bumper stopper
clearanceFollow spring clearance (Front)
Bumper stopper clearance (Rear)36 mm (1.42 in.)
104 mm (4.09 in.)
Front wheel align-
mentCamber Left−right error1°00’ ± 45’
45’ or less
Caster Left−right error3°00’ ± 60’
45’ or less
Steering axis inclination13 °00’ ± 45’
To e −in (Total) Inspection STD
Adjustment STD0.2 ° ± 0.2° (2 ± 2 mm, 0.08 ± 0.08 in.)
0.2 ° ± 0.1° (2 ± 1 mm, 0.08 ± 0.04 in.)
Wheel angle (Max.) Inside wheel
Outside wheel32 °00’ − 35°00’
31 °00’
Tire and wheelTire runout
Wheel balance (Unbalance after adjustment)
Wheel bearing preload (at starting) Front
(Rotating load at hub bolt) Rear3.0 mm (0.118 in.) or less
13.0 g (0.029 lb) or less
28 − 56 N (2.9 − 5.7 kgf, 6.4 − 12.6 lbf)
26 − 57 N (2.6 − 5.8 kgf, 5.7 − 12.8 lbf)
Front axleSteering knuckle bearing preload
(Rotating load at knuckle end, before installing dust seal)
25 − 44 N (2.5 − 4.5 kgf, 5.5 − 9.9 lbf)
Front dif ferentialDrive pinion preload (at starting) New bearing
Reused bearing0.9 − 1.6 N·m (10 − 16 kgf·cm, 8.7 − 13.9 in.·lbf)
0.5 − 0.8 N·m (5 − 8 kgf·cm, 4.3 − 6.9 in.·lbf)
Total preload (at starting)Drive pinion preload plus
0.4 − 0.6 N·m (4 − 6 kgf·cm, 3.5 − 5.2 in.·lbf)
Drive pinion to ring gear backlash0.13 − 0.18 mm (0.0051 − 0.0071 in.)
Pinion gear to side gear backlash0.05 − 0.20 mm (0.0020 − 0.0079 in.)
Ring gear runout Max.0.10 mm (0.0039 in.)
Companion flange runoutMax. Radial
Lateral0.10 mm (0.0039 in.)
0.10 mm (0.0039 in.)
Oil seal drive in depth1.0 mm (0.039 in.)
Side gear thrust washer thickness w/o Differntial lock
w/ Differntial lock1.6 mm (0.063 in.)
1.7 mm (0.067 in.)
1.8 mm (0.071 in.)
0.9 mm (0.035 in.)
1.0 mm (0.039 in.)
1.1 mm (0.043 in.)
1.2 mm (0.047 in.)
1.3 mm (0.051 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EK−02
−
SERVICE SPECIFICATIONS BODY
SS−41
164
Author: Date:
1996 LAND CRUISER (RM451U)
BODY
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
FRONT BUMPER
Front bumper arm x Front bumper bracket3940029
Front bumper arm x Body3940029
Front bumper extension x Front bumper5.45548 in.·lbf
REAR BUMPER
Rear bumper extension x Rear bumper reinforcement131309
Rear bumper extension reinforcement x Body5.45548 in.·lbf
HOOD
Hood hinge x Body1818513
Hood lock x Body88069 in.·lbf
FRONT DOOR
Door hinge x Body2424017
Door hinge x Door panel2424017
Door lock x Door panel55043 in.·lbf
Window regulator x Door panel55043 in.·lbf
REAR DOOR
Door hinge x Body2424017
Door hinge x Door panel2424017
Door lock x Door panel55043 in.·lbf
Window regulator x Door panel55043 in.·lbf
WIPER AND WASHER
Front wiper arm x Wiper link2021015
Wiper link x Body5.45548 in.·lbf
Wiper motor x Body5.45548 in.·lbf
Rear wiper arm x Wiper motor5.45548 in.·lbf
WHEEL OPENING EXTENSION
Front wheel opening extension x Body5.45548 in.·lbf
Rear wheel opening extension x Body5.45548 in.·lbf
INSTRUMENT P ANEL
Front passenger airbag assembly x Instrument panel reinforcement2021015
FRONT MANUAL SEAT
Seat truck x Body3940029
Seat reclining assembly x Seatback frame5253038
Lumber support x Seatback frame1818513
FRONT POWER SEAT
Seat truck x Body3940029
Power seat adjuster x Seatback frame3737527
Power seat adjuster x Seatback cushion frame1818513
Lumber support x Seatback frame1818513
NO. 1 REAR SEAT
Seat cushion hinge x Body3940029
Seat cushion hinge x Seat cushion frame3940029
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010