1996 TOYOTA LAND CRUISER lumbar support

BE1MP−01
BE−62
−
BODY ELECTRICAL POWER SEAT CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT POWER SEAT SWITCH (DRIVER’S SIDE) CONTINUITY
Slide switch:
Switch positionTester connectionSpecified condition
FORWARD5 − 10, 8 − 9Continuity
OFF5 − 8 − 9Continuity
BACKWARD5 − 9, 8 − 10Continuity
Front vertical switch:
Switch positionTester connectionSpecified condition
UP4 − 11, 10 − 12Continuity
OFF4 − 11 − 12Continuity
DOWN4 − 12, 10 − 11Continuity
Rear vertical switch:
Switch positionTester connectionSpecified condition
UP2 − 10, 6 − 7Continuity
OFF2 − 6 − 7Continuity
DOWN2 − 7, 6 − 10Continuity
Reclining switch:
Switch positionTester connectionSpecified condition
FORWARD4 − 10, 7 − 9Continuity
OFF4 − 7 − 9Continuity
BACKWARD4 − 9, 7 − 10Continuity
Lumbar support switch:
Switch positionTester connectionSpecified condition
FORWARD4 − 10, 7 − 9Continuity
OFF4 − 7 − 9Continuity
BACKWARD4 − 9, 7 − 10Continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−66
−
BODY ELECTRICAL POWER SEAT CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
11. INSPECT RECLINING MOTOR (PASSENGER’S SIDE)
OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2, and check that
the motor turns counterclockwise.
(b) Reverse the polarity, and check that the motor turns clockwise.
If operation is not as specified, replace the motor.
12. INSPECT RECLINING MOTOR (PASSENGER’S SIDE) CIRCUIT BREAKER OPERATION
(a) Connect the positive (+) lead from the battery to terminal 2 and the negative ( −) lead to terminal 1 on the seat wire
harness side connector, and recline the seat back to the
most forward position.
(b) Continue to apply voltage, and check that there is a circuit breaker operation noise within 4 to 40 seconds.
(c) Reverse the polarity, and check that the seat back starts to fall backwards within approximately 60 seconds.
If operation is not as specified, replace the motor.
13. INSPECT LUMBAR SUPPORT MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 2, and check that
the lumber support moves release side.
(b) Reverse the polarity, and check that the lumbar support moves forward.
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL POWER SEAT CONTROL SYSTEM
BE−67
1996 LAND CRUISER (RM451U)
14. INSPECT LUMBAR SUPPORT MOTOR CI RCUIT
BREAKER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (−) lead to terminal 1 on the lumbar
support motor connector and move the lumbar support to
front end position.
(b) Continue to apply voltage, and check that there is a circuit
breaker operation noise within 4 to 60 seconds.
(c) Reverse the polarity, and check that the lumbar support begins to move release side within approximately 60 se-
conds.
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010