1996 TOYOTA LAND CRUISER warning

Illustration:
what to do and where 21. CHECK
PISTON STROKE OF OVERDRIVE BRAKE
(a)
Task heading : what to do
SST 09350− 30020 (09350 −06120)
Set part No. Component part No.
Detailed text : how to do task
(b)
Piston stroke: 1.40  1.70 mm (0.0551  0.0669 in.)
Specification
Place SST and a dial indicator onto the overdrive brake pis-
ton as shown in the illustration.
Measure the stroke applying and releasing the compressed
air (392  785 kPa, 4  8 kgf/cm2 or 57 
114 psi) as shown
in the illustration.
IN−2
−
INTRODUCTION HOW TO USE THIS MANUAL
2
Author: Date:
1996 LAND CRUISER (RM451U)
The procedures are presented in a step −by−step format:
The illustration shows what to do and where to do it.
The task heading tells what to do.
The detailed text tells how to perform the task and gives other information\
such as specifications
and warnings.
Example:
This format provides the experienced technician with a FAST TRACK to the information needed. The upper
case task heading can be read at a glance when necessary, and the text below it provides detailed informa-
tion. Important specifications and warnings always stand out in bold type.
6. REFERENCES
References have been kept to a minimum. However, when they are required you are given the page to refer
to.
7. SPECIFICATIONS
Specifications are presented in bold type throughout the text where needed. You never have to leave the
procedure to look up your specifications. They are also found in Service Specificatio\
ns section for quick ref-
erence.
8. CAUTIONS, NOTICES, HINTS:
CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other\
people.
NOTICES are also presented in bold type, and indicate the possibility of damage to the components
being repaired.
HINTS are separated from the text but do not appear in bold. They provide additional information to
help you perform the repair efficiently.
9. SI UNIT
The UNITS given in this manual are primarily expressed according to the SI UNIT (Intern\
ational System of
Unit), and alternately expressed in the metric system and in the English Syste\
m.
Example:
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Illustration:
what to do and where 21. CHECK
PISTON STROKE OF OVERDRIVE BRAKE
(a)
Task heading : what to do
SST 09350− 30020 (09350 −06120)
Set part No. Component part No.
Detailed text : how to do task
(b)
Piston stroke: 1.40  1.70 mm (0.0551  0.0669 in.)
Specification
Place SST and a dial indicator onto the overdrive brake pis-
ton as shown in the illustration.
Measure the stroke applying and releasing the compressed
air (392  785 kPa, 4  8 kgf/cm2 or 57 
114 psi) as shown
in the illustration.
IN−2
−
INTRODUCTION HOW TO USE THIS MANUAL
2
Author: Date:
1996 LAND CRUISER (RM451U)
The procedures are presented in a step −by−step format:
The illustration shows what to do and where to do it.
The task heading tells what to do.
The detailed text tells how to perform the task and gives other information\
such as specifications
and warnings.
Example:
This format provides the experienced technician with a FAST TRACK to the information needed. The upper
case task heading can be read at a glance when necessary, and the text below it provides detailed informa-
tion. Important specifications and warnings always stand out in bold type.
6. REFERENCES
References have been kept to a minimum. However, when they are required you are given the page to refer
to.
7. SPECIFICATIONS
Specifications are presented in bold type throughout the text where needed. You never have to leave the
procedure to look up your specifications. They are also found in Service Specificatio\
ns section for quick ref-
erence.
8. CAUTIONS, NOTICES, HINTS:
CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other\
people.
NOTICES are also presented in bold type, and indicate the possibility of damage to the components
being repaired.
HINTS are separated from the text but do not appear in bold. They provide additional information to
help you perform the repair efficiently.
9. SI UNIT
The UNITS given in this manual are primarily expressed according to the SI UNIT (Intern\
ational System of
Unit), and alternately expressed in the metric system and in the English Syste\
m.
Example:
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN−10
−
INTRODUCTION FOR ALL OF VEHICLES
10
Author: Date:
1996 LAND CRUISER (RM451U)
(3) Even in cases of a minor collision where the SRS
does not deploy, the steering wheel pad (See page
RS−9) and front passenger airbag assembly (See
page RS−23 ) should be inspected.
(4) Never use SRS parts from another vehicle. When replacing parts, replace them with new parts.
(5) Before repairs, remove the airbag sensor if shocks
are likely to be applied to the sensor during repairs.
(6) Never disassemble and repair the airbag sensor as-
sembly, steering wheel pad or front passenger air-
bag assembly in order to reuse them.
(7) If the airbag sensor assembly, steering wheel pad
or front passenger airbag assembly have been
dropped, or if there are cracks, dents or other de-
fects in the case, bracket or connector, replace
them with new ones.
(8) Do not directly expose the airbag sensor assembly, steering wheel pad or front passenger airbag as-
sembly to hot air or flames.
(9) Use a volt/ohmmeter with high impedance (10 kΩ/V
minimum) for troubleshooting of the electrical cir-
cuit.
(10) Information labels are attached to the periphery of the SRS components. Follow the instructions on the
notices.
(11) After work on the supplemental restraint system is completed, check the SRS warning light (See page
DI−240 ).
(c) SPIRAL CABLE (in Combination Switch) The steering wheel must be fitted correctly to the steering
column with the spiral cable at the neutral position, other-
wise cable disconnection and other troubles may result.
Refer to SR−19 of this manual concerning correct steer-
ing wheel installation.
RedMarkROOJll
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LT−01
BE−2
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
SymptomSuspect AreaSee page
Ignition switch is not set to each position.5. Ignition SwitchBE−11
”Key unlock warning system” does not operate.
1. GAUGE Fuse (I/P F/B)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire Harness−
BE−11
BE−21 −
HEADLIGHT AND TAILLIGHT SYSTEM
SymptomSuspect AreaSee page
Headlight does not light up. (Taillight is normal.)
1. Headlight Bulb
2. MAIN FL
3. HEAD (LH) Fuse (No.2 R/B)
4. HEAD (RH) Fuse (No.2 R/B)
5. Light Control Switch
6. Headlight Dimmer Switch
7. Wire Harness−
−
−
−
BE−14
BE−14
−
Headlight does not light up. (Taillight does not light up.)
1. Headlight Bulb
2. Light Control Switch
3. Headlight Dimmer Switch
4. Wire Harness−
BE−14
BE−14 −
Only one light comes ON.
1. Headlight Bulb
2. HEAD (LH) Fuse (No.2 R/B)
3. HEAD (RH) Fuse (No.2 R/B)
4. Wire Harness−
−
−
−
”Lo− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Hi− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Flash” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
Taillight does not light up. (Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (I/P F/B)
3. Light Control Switch
4. Taillight Control Relay (No.2 R/B)
5. Wire Harness−
−
BE−14
BE−14 −
Taillight does not light up. (Headlight does not light up.)
1. Taillight Bulb
2. MAIN FL
3. TAIL Fuse (I/P F/B)
4. Light Control Switch
5. Wire Harness−
−
−
BE−14 −
Headlight and Taillight does not light.1. Light Control Switch
2. Wire HarnessBE−14
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−3
1996 LAND CRUISER (RM451U)
Only one side taillight does not light.
1. Taillight Bulb
2. Wire Harness−
−
Taillight does not light.
(Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (No.2 R/B)
3. Taillight Control Relay (No.2 R/B)
4. Light Control Switch
5. Wire Harness−
BE−14
BE−14
BE−14 −
TURN SIGNAL AND HAZARD WARNING SYSTEM
SymptomSuspect AreaSee page
”Hazard” and ”Turn” do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher (No.1 R/B)
3. Wire HarnessBE−19
BE−19
−
None of blinks for hazard. (Turn is normal.)
1. Bulb
2. Turn Signal Flasher (No.1 R/B)
3. Wire Harness−
BE−19 −
Hazard warning light does not light up. (Turn is normal.)1. HAZ − HORN Fuse (No.2 R/B)
2. Wire HarnessBE−19 −
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE−19−
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Flasher (No.1 R/B)
3. Wire Harness−
BE−19 −
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE−19−
Only one bulb does not light up for hazard turn.1. Bulb
2. Wire Harness−
−
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. Ignition Switch
2. TURN Fuse (I/P F/B)
3. Turn Signal Switch
4. Wire HarnessBE−11
BE−19
BE−19 −
Turn signal does not light up.
(Combination meter, wiper and washer are normal.)1. TURN Fuse (I/P F/B)
2. Turn Signal Switch
3. Wire HarnessBE−19
BE−19−
INTERIOR LIGHT SYSTEM
SymptomSuspect AreaSee page
Room light does not light up.
1. DOME Fuse (No.2 R/B)
2. Door Courtesy Switch
3. Front Personal Light
4. Room Light Assembly
5. Bulb
6. Wire Harness−
BE−21
BE−21
BE−21 −
−
Room light remains always on.1. Door Courtesy Switch
2. Wire HarnessBE−21
−
BACK −UP LIGHT SYSTEM
SymptomSuspect AreaSee page
Back−Up light does not light up.
1. GAUGE Fuse (I/P F/B)
2. Ignition Switch
3. Park/Neutral Position Switch (A/T)
4. Bulb
5. Wire Harness−
BE−11 −
−
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−5
1996 LAND CRUISER (RM451U)
Fuel gauge does not operate or abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32
−
Engine coolant temperature gauge does not operation or
abnormal operate.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32−
Oil pressure gauge does not operate or abnormal operation.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−34−
All illumination lights do not light up.
1. TAIL Fuse (I/P F/B)
2. Light Control Rheostat
3. Wire Harness−
BE−34 −
Brightness does not change even when rheostat turned.1. Bulb
2. Wire Harness−
−
Only one illumination light does not light up.1. Bulb
2. Wire Harness−
−
WARNING LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
Warning lights do not lights up.
(Except discharge, SRS and door open)1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Brake warning light does not light up.
1. Bulb
2. Brake Fluid Level Switch
3. Parking Brake Switch
4. Meter Circuit
5. Wire Harness−
BE−34
BE−34
BE−32 −
Open door warning light does not light up.
1. Bulb
2. Door Courtesy Switch
3. DOME Fuse (No.2 R/B)
4. Meter Circuit
5. Wire Harness−
BE−21
BE−21 −
−
−
SRS warning light does not light up
1. Bulb
2. Airbag Sensor Assembly
3. ECU− B Fuse (I/P F/B)
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Discharge warning light does not light up.
1. Bulb
2. IGN Fuse (No.1 J/B)
3. Generator
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Seat belt warning light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Seat Belt Warning Relay (I/P F/B)
4. Meter Circuit
5. Wire Harness−
BE−34 −
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−6
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Engine oil level warning light does not light up.
1. Bulb
2. Meter Circuit
3. Engine Oil Level Warning Switch
4. Wire Harness−
BE−32
BE−34 −
Low oil pressure warning light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−32
BE−34 −
Fuel level warning light does not light up.
1. Bulb
2. Fuel Level Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−34
BE−32 −
INDICATOR LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
High beam indicator light does not light up.
1. Bulb
2. Headlight and Taillight System
3. Meter Circuit
4. Wire Harness−
BE−19
BE−32 −
Shift indicator lights do not light up. (ALL)
1. Shift Position Indicator Wiring Circuit
2. Park/Neutral Position Switch
3. Wire Harness
4. Bulb−
BE−34 AT −6
−
Shift indicator lights do not light up. (L, 2, D)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Park/Neutral Position Switch
4. Light Control Rheostat
5. Wire Harness−
BE−34 AT −6
BE−34 −
Shift indicator lights do not light up. (PWR)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Pattern Select Switch
4. Wire Harness−
BE−34 AT −6
−
Shift indicator lights do not light up. (2nd START)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. ECM
4. Wire Harness−
AT −6
−
−
Only one shift indicator does not light up.1. Bulb
2. Shift Position Indicator Wiring Circuit−
BE−34
Indicator lights do not light up. (Except Turn, Hi −beam)1. GAUGE Fuse (I/P F/B)
2. Wire Harness−
−
O/D OFF indicator light does not light up.
1. Bulb
2. O/D Main Switch
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Malfunction indicator light does not light up.
1. Bulb
2. ECM
3. Wire Harness−
−
−
Cruise control indicator light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−7
1996 LAND CRUISER (RM451U)
DEFOGGER SYSTEM
SymptomSuspect AreaSee page
Defogger system does not operate.
1. DEFOG Fuse (I/P F/B)
2. GAUGE Fuse (I/P F/B)
3. Defogger Switch
4. Defogger Relay (No.1 R/B)
5. Defogger Wire
6. Wire Harness−
−
BE−43
BE−43 −
−
POWER WINDOW CONTROL SYSTEM
SymptomSuspect AreaSee page
Power window does not operate (ALL).
(Power door lock does not operate.)
1. POWER Fuse (I/P F/B)
2. GAUGE Fuse (I/P F/B)
3. Power Main Relay (No.1 R/B)
4. Wire Harness−
−
−
−
Power window does not operate (ALL).
(Power door lock is normal.)
1. Ignition Switch
2. Power Main Relay (No.1 R/B)
3. Power Window Master Switch
4. Wire HarnessBE−11
−
BE−46 −
”One touch power window system” does not operate.1. Power Window Master SwitchBE−46
Only one window glass does not operate.
1. Power Window Master Switch
2. Power Window Switch
3. Power Window Motor
4. Wire HarnessBE−46
BE−46
BE−46−
POWER DOOR LOCK CONTROL SYSTEM
SymptomSuspect AreaSee page
Power door lock control system does not operate (ALL).
1. POWER Fuse (I/P F/B)
2. Power Main Relay (No.1 R/B)
3. Wire Harness−
−
−
Power door lock control system does not operate by door lock
control switch.1. Door Lock Control Switch
2. Power Main Relay (No.1 R/B)
3. Wire HarnessBE−51
−
−
Power door lock control system does not operate by door key.
1. Door Key Lock and Unlock Switch
2. Power Main Relay (No.1 R/B)
3. Wire HarnessBE−11−
−
Only one door does not operate.
1. Door Lock Motor
2. Door Lock Link Disconnected
3. Wire HarnessBE−51 −
−
Fault in key confine prevention operation.
1. Power Main Relay (No.1 R/B)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire Harness−
BE−11
BE−21 −
SLIDING ROOF SYSTEM
SymptomSuspect AreaSee page
Sliding roof system does not operate.
(Door lock does not operate.)
1. GAUGE Fuse (I/P F/B)
2. Ignition Switch
3. POWER Fuse (No.1 J/B)
4. Power Main Relay (No.1 R/B)
5. Sliding Roof Control Switch
6. Sliding Roof Control Relay
7. Sliding Roof Motor
8. Wire Harness−
BE−11 −
−
BE−58
BE−58
BE−58
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010