1996 TOYOTA LAND CRUISER warning

BE1LV−01
BE−10−
BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING
SWITCH
1148
Author: Date:
1996 LAND CRUISER (RM451U)
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LW−01
−
BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE−11
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT IGNITION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK−No continuity
ACC7 − 9Continuity
ON3 − 4, 6 − 7 − 9Continuity
START2 − 3 − 4
6 − 9 − 10Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SWITCH CONTINUITY
ConditionTester connectionSpecified condition
SW OFF
(Key removed)−No continuity
SW ON (Key set)1 − 5Continuity
If continuity is not as specified, replace the switch.
3. INSPECT DOOR COURTESY SWITCH CONTINUITY
(See page BE−21 )
4. INSPECT SEAT BELT WARNING RELAY CIRCUIT
(See page BE−34 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M1−01
BE−18
−
BODY ELECTRICAL TURN SIGNAL AND HAZARD WARNING SYSTEM
1156
Author: Date:
1996 LAND CRUISER (RM451U)
TURN SIGNAL AND HAZARD WARNING SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE27G−01
BE1843
−
BODY ELECTRICAL TURN SIGNAL AND HAZARD WARNING SYSTEM
BE−19
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT HAZARD WARNING SWITCH CONTINUITY
ConditionTester connectionSpecified condition
Switch OFF7 − 10Continuity
Switch ON7 − 8
4 − 5 − 6 − 9Continuity
Illumination circuit2 − 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative ( −) lead to terminal 3.
(b) Connect the 2 turn signal light bulbs parallel to each other
to terminals 1 and 3, and check that the bulbs flash.
HINT:
The turn signal lights should flash 60 to 120 times per minute.
If one of the front or rear turn signal lights has an open circuit,
the number of flashes will be more than 140 per minute.
If operation is not as specified, replace the flasher.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−36
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
7. INSPECT FUEL SENDER GAUGE OPERATION
(a) Connect a series of three 1.5 V dry cell batteries.
(b) Connect the positive (+) lead from the dry cell batteries to
terminal 4 through a 3.4 W test bulb and the negative ( −)
lead to terminal 5.
(c) Connect the positive (+) lead from the voltmeter to termi- nal 4 and the negative ( −) lead to terminal 5.
(d) Check that the voltage rises as the float is moved from the
full to empty position.
8. INSPECT FUEL SENDER GAUGE RESISTANCE
Measure the resistance between terminals 4 and 5.
Float position: mm (in.)Resistance (Ω )
F: Approx. 15.0 (0.591)Approx. 3.0
E: Approx. 200.0 (7.874)Approx. 110.0
If resistance value is not as specified, replace the sender
gauge.
9. INSPECT FUEL LEVEL WARNING LIGHT
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 1 and 5 on the wire harness side con-
nector.
(c) Turn the ignition switch ON, and check that the warning
light lights up.
If the warning light does not light up, test the bulb.
10. INSPECT FUEL LEVEL WARNING SWITCH
(a) Apply battery positive voltage between terminals 1 and 5
through a 3.4 W test bulb, and check that the bulb lights
up.
HINT:
It will take a short time for the bulb to light up.
(b) Submerge the switch in fuel, and check that the bulb goes
out.
If operation is not as specified, replace the sender gauge.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE4917
Test LED
Battery
BE1217
Warning Light
Ignition
Switch Battery
N01212
BE−38
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
(c) Ground terminal on the wire harness side through a 3.4
W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and that the receiver gauge needle moves to the high
side.
If operation is not as specified, measure the receiver gauge re-
sistance.
14. INSPECT OIL PRESSURE RECEIVER GAUGE RESIS- TANCE
Measure the receiver gauge resistance between terminals. Resistance:
40 − 48 Ω
If resistance value is not as specified, replace the receiver
gauge.
15. INSPECT OIL PRESSURE SENDER GAUGE OPERA-
TION
(a) Disconnect the connector from the sender gauge.
(b) Apply battery positive voltage to the sender gauge termi- nal through a test LED.
(c) Check that the bulb does not light when the engine is stopped.
(d) Check that the LED flashes when the engine is running. The number of flashed should vary with engine speed.
If operation is not as specified, replace the sender gauge.
16. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connectors from the level warning switch and parking brake switch.
(b) Connect terminals on the wire harness side connector of
the level warning switch connector.
(c) Turn the ignition switch ON, and check that the warning light lights up.
17. INSPECT PARKING BRAKE SWITCH
(a) Check that there is continuity between terminal and the switch set nut with switch pin released (parking brake le-
ver pulled up).
(b) Check that there is no continuity between terminal and the switch set nut with switch pin pushed in. (parking
brake lever released)
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE2570
ON
OFF
BE0044
BE1428
−
BODY ELECTRICAL COMBINATION METER
BE−39
1996 LAND CRUISER (RM451U)
18. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
(a) Check that there is no continuity between terminals with
the switch OFF (float up).
(b) Check that there is continuity between terminals with the switch ON (float down).
If operation is not as specified, replace the switch.
19. INSPECT OPEN DOOR WARNING LIGHT
(a) Disconnect the connector from the door courtesy switch and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON, and check that the warning light lights up.
If the warning light does not light up, test the bulb.
20. INSPECT DOOR COURTESY SWITCH
(a) Check that there is continuity between terminal and the
switch body with the switch ON (switch pin re-
leased:opened door).
(b) Check that there is no continuity between terminal and
the switch body with the switch OFF (switch pin pushed
in:closed door).
If operation is not as specified, replace the switch.
21. INSPECT SEAT BELT WARNING LIGHT
(a) Disconnect the connector from the seat belt warning relay.
(b) Ground terminal 9 on the wire harness side connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up.
If the warning light does not light up, test the bulb.
22. INSPECT SEAT BELT BUCKLE SWITCH CONTINUITY
(a) Check that there is continuity between terminals with the switch ON (belt unfastened).
(b) Check that there is no continuity between terminals with the switch OFF (belt fastened).
If operation is not as specified, replace the seat belt inner.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−40
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
23. INSPECT SEAT BELT WARNING RELAY CIRCUIT
Disconnect the connector from the relay and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
1 − GroundConstantContinuity
4 − GroundDriver’s seat belt position UNFASTENContinuity
4 − GroundDriver’s seat belt position FASTENNo continuity
7 − GroundIgnition key SETContinuity
7 − GroundIgnition key RemoveNo continuity
8 − GroundDriver’s door position OPENContinuity
8 − GroundDriver’s door position CLOSENo continuity
5 − GroundIgnition switch position ONBattery positive voltage
5 − GroundIgnition switch position LOCK or ACCNo voltage
9 − GroundConstantBattery positive voltage
If circuit is as specified, try another relay.
If the circuit is not as specified, check the circuits connected to
other parts.
24. INSPECT ENGINE OIL LEVEL WARNING SWITCH
(a) Check that there is continuity between terminal with the
switch each position.
(b) Heat the switch to above 60° C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010