−
INTRODUCTION TERMS
IN−37
37
Author: Date:
1996 LAND CRUISER (RM451U)
TC
Turbocharger
TCCSTOYOTA
Computer− Controlled System
TCVTiming Control V alve
TDCTop Dead Center
TEMP.Temperature
TEMSTOYOTA Electronic Modulated Suspension
TISTotal Information System For Vehicle Development
T/MTransmission
TMCTOYOTA Motor Corporation
TMMKTOYOTA Motor Manufacturing Kentucky, Inc.
TRACTraction Control System
TURBOTurbocharge
U/DUnderdrive
U/SUndersize
VCVVacuum Control V alve
VENTVentilator
VINVehicle Identification Number
VPSVariable Power Steering
VSCVehicle Skid Control
VSVVacuum Switching Valve
VTVVacuum Transmitting V alve
w/With
WGNWagon
W/HWire Harness
w/oWithout
1stFirst
2ndSecond
2WDTwo Wheel Drive Vehicle (4x2)
4WDFour Wheel Drive Vehicle (4x4)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Q07310Control Shaft Lever(b)
(c)
Q07311
Neutral Basic Line
Bolt
Groove
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−139
1996 LAND CRUISER (RM451U)
(3) Return the control shaft lever 2 notches to N posi-
tion.
(4) Set the shift lever to N position.
(5) While holding the shift lever lightly toward the R
position side, adjust the control rod nut.
(6) Tighten the control rod nut.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(7) Start the engine and make sure that the vehicle moves forward when shifting the lever from the N to
D position and reverses when shifting it to the R
position.
(g) Inspec and adjust park/neutral positoin switch. Check that the engine can be started with the shift lever
only in the N or P position, but not in other positions.
If not as stated above, carry out the following adjustment proce-
dure.
(1) Loosen the park/neutral position switch bolt and set
the shift lever to the N position.
(2) Align the groove and neutral basic line.
(3) Hold in position and tighten the bolt.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf) For continuity inspect of the park/neutral position
switch, see page DI−169 .
(h) Check the idle speed. Idle speed:
650 ± 50 rpm (In N position and air conditioner OFF)
7. MECHANICAL SYSTEM TESTS
(a) Measure the stall speed. The object of this test is to check the overall performance of the transmis\
sion and engine by measuring
the stall speeds in the D and R positions.
NOTICE:
Do the that at normal operating ATF temperature 50 − 80°C (122 − 176° F).
Do not continuously run this test longer than 5 seconds.
To ensure safety, conduct this test in a wide, clear, level area which provides good traction.
The stall test should always be carried out in pairs. One technician should\
observe the condi-
tions of wheels or wheel stoppers outside the vehicle while the other is doin\
g the test.
(1) Chock the 4 wheels.
(2) Connect an OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(3) Fully apply the parking brake.
(4) Keep your left foot pressed firmly on the brake pedal.
(5) Start the engine.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
