1996 TOYOTA LAND CRUISER Wheel bearings

P22572
P22574B13834
Drain Plug
Drain Plug
MA0621B13835
Lubricating Positions: 1. Spider2. Slide Yoke1
2 1
MA−8
−
MAINTENANCE CHASSIS
48
Author: Date:
1996 LAND CRUISER (RM451U)
7. REPLACE TRANSFER AND DIFFERENTIAL OIL
(a) Remove the drain plug and drain the oil.
(b) Reinstall the drain plug securely.
(c) Add new oil until it begins to run out of the filler hole.
Oil drade and viscosity: See step 5.
Oil capacity:
Transfer oil
1.7 liters (1.8 US qts, 1.5 lmp. qts)
Front differential oil (w/o Differential lock)
2.8 liters (3.0 US qts, 2.5 lmp. qts)
Front differential oil (w/ Differential lock)
2.65 liters (2.8 US qts, 2.3 lmp. qts)
Rear differential oil
3.25 liters (3.4 US qts, 2.9 lmp. qts)
8. REPACK FRONT WHEEL BEARINGS (See pages SA−7 and SA−9 )
9. LUBE STEERING KNUCKLE CHASSIS AND PROPEL-
LER SHAFT
(a) Remove the screw plug from each steering knuckle and repack with lubricant.
Steering knuckle grease:
Molybdenum disulfide lithium base chassis grease
(NLGI No. 2)
(b) Reinstall the 2 screw plugs.
(c) Lubricate chassis components, referring to the lubrication
chart. Before pumping in grease, wipe off any mud and
dust on the grease fitting.
Grease grade:
Lithium base chassis grease (NLGI No. 2)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1U7−01
−
SUSPENSION AND AXLE TROUBLESHOOTING
SA−1
858
Author: Date:
1996 LAND CRUISER (RM451U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers \
indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
(w/ Differential locking system):
Check that center differential lock mode is set.
When switching differential Free↔Lock, the indicator lamp will blink if the gears of the differen-
tial lock sleeve are not meshed. If this occurs, when the tires are rotated \
to apply differential
power to the differential, the differential locks and the indicator lamp\
light up.
SymptomSuspect AreaSee page
Wander/ pulls
1. Tires: worn or improperly inflated
2. Wheel alignmemt: incorrect
3. Steering linkage: loosen or worn
4. Hub bearings: loosen or worn
5. Steering gear: out of adjustment or brokenSA−3
SA−4
SR−47 SA−8
SR−41
Bottoming
1. Vehicle: overloaded
2. Spring weak
3. Shock absorber: worn out−
SA−49
SA−49
Sways/ pitches
1. Tires: worn or improperly inflated
2. Stabilizer bar: bent or broken
3. Shock absorber: worn outSA−3
SA−60
SA−49
Front wheel shimmy
1. Tires: worn or improperly inflated
2. Wheels: out of balance
3. Shock absorber: worn out
4. Wheel alignmemt: incorrect
5. Hub bearings: loosen or worn
6. Steering linkage: loosen or worn
7. Steering gear: out of adjustment or brokenSA−3
SA−3
SA−49 SA−3
SA−7
SR−45
SR−38
Abnormal tire wear
1. Tires: worn or improperly inflated
2. Wheel alignmemt: incorrect
3. Suspension parts: worn out
4. Shock absorber: worn outSA−3
SA−3 −
SA−49
Noise in front dif ferential
1. Oil level: low or wrong grade
2. Excessive backlash between pinion and ring gear
3. Ring, pinion ro side gears: worn or chipped
4. Pinion shaft bearing: worn
5. Side bearing: worn
6. Differential bearing: loosen or wornSA−21
SA−29
SA−29
SA−29
SA−29
SA−29
Oil leak from front dif ferential
1. Oil level: too high or wrong grade
2. Drive pinion oil seal: worn or damaged
3. Side gear oil seal: worn or damaged
4. Companion flange: loosen or damaged
5. Side gear shaft: damagedSA−21
SA−29
SA−29
SA−29
SA−29
Noise in rear axle
1. Oil level: low or wrong grade
2. Excessive backlash between pinion and ring gear
3. Ring, pinion ro side gears: worn or chipped
4. Pinion shaft bearing: worn
5. Axle shaft bearing: worn
6. Differential bearing: loosen or wornSA−73
SA−87
SA−87
SA−87
SA−87
SA−87
Oil leak from rear axle1. Oil seal: worn or damaged
2. Rear axle housing: crackedSA−73
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1UI−01
SA2650
SST
Z15221
Lithium Base Wheel Bearing
Grease, NIGI No.2
R08387SST
R08388
SST
−
SUSPENSION AND AXLE STEERING KNUCKLE AND AXLE SHAFT
SA−17
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL OIL SEAL TO AXLE HOUSING
Using SST and a hammer, install a new oil seal into the axle
housing.
SST 09618−60010
2. INSTALL OIL SEAL SET
Install these parts to the steering knuckle:
Oil seal and retainer
Felt dust seal
Rubber seal and steel ring
3. PACK BEARINGS WITH LITHIUM BASE WHEEL
BEARING GREASE, NLGI NO.2
(a) Place lithium base wheel bearing grease, NLGI No.2 on your hand.
(b) Pack grease into the bearing until the grease oozes out from the outer side.
(c) Do the same around the bearing circumference.
4. INSTALL STEERING KNUCKLE AND BEARINGS
(a) Place the bearings in positions on the knuckle and axle housing.
(b) Install the knuckle on the axle housing.
5. INSTALL KNUCKLE ARM AND BEARING CAP
(a) Using SST, support the upper bearing inner race. SST 09606−60020
HINT:
Use the SST with a collar.
(b) Install the bearing cap over the shim that were originally
used.
(c) Using a hammer, install the bearing cap into the bearing
inner race.
(d) Using SST, support the lower bearing inner race. SST 09606−60020
HINT:
Use the SST with a collar.
(e) Using a hammer, tap the knuckle arm and shim into the
bearing inner race.
(f) Remove the SST from the knuckle.
(g) Install the 4 cone washers and nuts.
Torque: 96 N·m (980 kgf·cm, 71 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010