1996 TOYOTA LAND CRUISER egr sensor

−
INTRODUCTION FOR ALL OF VEHICLES
IN−13
13
Author: Date:
1996 LAND CRUISER (RM451U)
(f) AIRBAG SENSOR ASSEMBLY
The connectors to the airbag sensor assembly should be
connected or disconnected with the sensor mounted on
the floor. If the connectors are connected or disconnected
while the airbag sensor assembly is not mounted to the
floor, it could cause undesired ignition of the supplemen-
tal restraint system.
(g) WIRE HARNESS AND CONNECTOR The SRS wire harness is integrated with the cowl wire har-
ness assembly and floor wire harness assembly. The
wires for the SRS wire harness are encased in a yellow
corrugated tube. All the connectors for the system are
also a standard yellow color. If the SRS wire harness be-
comes disconnected or the connector becomes broken
due to an accident, etc., repair or replace it as shown on
page RS−37 .
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−12
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
(b) TOYOTA Enhanced Signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.0 − 3.5 ms
IAC STEP POSIntake Air Control Valve step position
Opening position step motor type IAC valveIdling: 10 − 50 step
STARTER SIGStarter SignalCranking: ON
CTP SWClosed Throttle Position Switch SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N Position: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1 − CYL#6Ratio of revolution variation for each cylinder
when variation is large0%
IGNITIONIgnition rate for all cylinders every 1,000 revolu-
tions0 − 3,000 rpm
EGRT GASEGR Gas Temp. Sensor V alueEGR not operating: Temp. between intake air
temp. and engine coolant temp.
EGR SYSTEMEGR System Operating ConditionIdling: OFF
FUEL PRES UP VSVFuel Pressure Up VSV SignalHigh temp. restarting: ON
FUEL PUMPFuel Pump SignalIdling: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from lean to rich
Idling after warmed up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from rich to lean
Idling after warmed up: 0 − 1,000 msec.
∗: If no conditions are specifically stated for ”ldling”, it means t\
he shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−14
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC No.
(See Page)
Detection ItemTrouble AreaMILMemory
P0171
( DI−51 )System too Lean
(Fuel T rim)
Air intake (hose loose)
 Fuel line pressure, leak
 Injector blockage
 Heated oxygen sensor malfunction
 Mass air flow meter
 Engine coolant temp. sensor
 *1
P0172
( DI−51 )System too Rich
(Fuel T rim)
Fuel line pressure
 Injector leak, blockage
 Heated oxygen sensor malfunction
 Mass air flow meter
 Engine coolant temp. sensor
 *1
P0300
( DI−54 )Random/Multiple Cylinder
Misfire DetectedIgnition system
 Injector
 Fuel line pressure
 EGR
 Compression pressure
 Valve clearance not to specification
 Valve timing
 Mass air flow meter
 Engine coolant temp. sensor
 *2
P0301
P0302
P0303
P0304
P0305
P0306
( DI−54 )Misfire Detected
− Cylinder 1
− Cylinder 2
− Cylinder 3
− Cylinder 4
− Cylinder 5
− Cylinder 6
P0325
( DI−59 )Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
 Knock sensor 1 (looseness)
 ECM
 *1
P0330
( DI−59 )Knock Sensor 2 Circuit
MalfunctionOpen or short in knock sensor 2 circuit
 Knock sensor 2 (looseness)
 ECM
 *1
P0335
( DI−62 )Crankshaft Position Sensor
”A” Circuit Malfunction
Open or short in crankshaft position sensor circuit for NE sig-
nal
 Crankshaft position sensor for NE signal
 Starter
 ECM
 *1
P0340
( DI−65 )Camshaft Position Sensor
Circuit MalfunctionOpen or short in camshaft position sensor circuit
 Camshaft position sensor
 ECM
 *1
P0385
( DI−67 )Crankshaft Position Sensor
”B” Circuit Malfunction
Open or short in crankshaft position sensor circuit for NE2
signal
 Crankshaft position sensor for NE2 signal
 ECM
 *1
P0401
( DI−69 )Exhaust Gas Recirculation
Flow Insufficient Detected
EGR valve stuck closed
 Short in VSV circuit for EGR
 Open in EGR gas temp. sensor circuit
 EGR hose disconnected
 ECM
 *1
P0402
( DI−80 )Exhaust Gas Recirculation
Flow Excessive Detected
EGR valve stuck open
 EGR VSV open malfunction
 Open in VSV circuit for EGR
 Short in EGR gas temp. sensor circuit
 ECM
 *1
*1: MIL lights up
*2: MIL lights up or blinking
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−54
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
DTC P0300 Random/Multiple Cylinder Misfire Detected
DTC P0301 Cylinder 1 Misfire Detected
DTC P0302 Cylinder 2 Misfire Detected
DTC P0303 Cylinder 3 Misfire Detected
DTC P0304 Cylinder 4 Misfire Detected
DTC P0305 Cylinder 5 Misfire Detected
DTC P0306 Cylinder 6 Misfire Detected
CIRCUIT DESCRIPTION
Misfire: The ECM uses the crankshaft position sensor and camshaft position senso\
r to monitor changes in
the crankshaft rotation for each cylinder.
The ECM counts the number of times the engine speed change rate indicates that misfire has occurred.
When the misfire rate equals or exceeds the count indicating that the engine condition has deteriorat\
ed, the
MIL lights up.
If the misfire rate is high enough and the driving conditions will cause catalyst overheating, the MIL blinks
when misfiring occurs.
DTC No.DTC Detecting ConditionTrouble Area
P0300Misfiring of random cylinders is detected during the any partic-
ular 200 or 1,000 revolutions Ignition system
 Injector
 Fuel line pressure
 EGR
 Compression pressure
 Valve clearance not to specification
 Valve timing
 Mass air flow meter
 Engine coolant temp. sensor
P0301
P0302
P0303
P0304
P0305
P0306For any particular 200 revolutions of the engine, misfiring is
detected which can cause catalyst overheating
(This causes MIL to blink)
For any particular 1,000 revolutions of the engine, misfiring is
detected which causes a deterioration in emission
(2 trip detection logic)
HINT:
When the 2 or more codes for a misfiring cylinder are recorded repeatedly bu\
t no random misfire code is
recorded, it indicates that the misfires were detected and recorded at d\
ifferent times.
DI5PF−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−58
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
5 Check injector injection (See page SF−29).
NG Replace injector.
OK
6 Check EGR system (See page EC−11 ).
NG Repair EGR system.
OK
7 Check mass air flow meter and engine coolant temp. sensor (See page SF−40 ,
SF−61 ).
NG Repair or replace.
OK
Check engine mechanical systems compression pressure (See page EM−3), valve clearance
(See page EM−4) and valve timing (See page EM−13).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22417
Exhaust
Gas
Intake Air
Chamber EGR
Valve
VSV
EGR
Vacuum
Modulator
ECM
Throttle
valve
P22426
BR
From Battery R/B No.2
R−Y
2
222
2
2
Y−R
EFI Main
Y−R
1
2
43
REA2
EZ1
EB12 7
VSV for EGR 21
YYL
−W
EZ14
EGR Gas T emp.
Sensor
21
G−Y
BR−BE7 E4
E4
E5 3
22
19
9
THG
E1
EGR
E2 5V
MRLY
ECM
R
EB
EFI
1
Relay
B+
E01
−
DIAGNOSTICS ENGINE
DI−69
1996 LAND CRUISER (RM451U)
DTC P0401 Exhaust Gas Recirculation Flow Insufficient
Detected
CIRCUIT DESCRIPTION
The EGR system recirculates exhaust gas, which is controlled to the proper \
quantity to suit the driving condi-
tions, into the intake air mixture to slow down combustion, reduce the combust\
ion temp. and reduce NOx
emissions. The amount of EGR is regulated by the EGR vacuum modulator ac\
cording to the engine load.
If even one of the following conditions is fulfilled, the VSV is
turned ON by a signal from the ECM.
This results in atmospheric air acting on the EGR valve, closing
the EGR valve and shutting off the exhaust gas (EGR cut− off).
Under the following conditions, EGR is cut to maintain driveabil-
ity.
Before the engine is warmed up.
During deceleration (throttle valve closed).
Light engine load (amount of intake air very small).
Engine racing.
DTC No.DTC Detecting ConditionTrouble Area
P0401
After the engine is warmed up and run at 80 km/h (50 mph)
for 3 to 5 minutes, the EGR gas temperature sensor value
does not exceed 38° C (100.4°F) above the ambient air tem-
perature. (2 trip detection logic) EGR valve stuck closed
 Short in VSV circuit for EGR
 Open in EGR gas temp. sensor circuit
 EGR hose disconnected
 ECM
WIRING DIAGRAM
DI5PK−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00168
ON
EGR Gas Temp.
Sensor ECM
19 9
1
2
BE6653
FI7055 THG
E2
E4
E5 5V
−
DIAGNOSTICS ENGINE
DI−71
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and read value of EGR gas temp. value.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and push the TOYOTA hand −held tester main switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: 10° C (50°F) or more
HINT:
If there is and open circuit, the TOYOTA hand−held tester indicates 3.1 °C (37.6° F).
OK Go to step 4.
NG
2 Check for open in harness or ECM.
PREPARATION:
(a) Disconnect the EGR gas temp. sensor connector.
(b) Connect sensor wire harness terminals together.
(c) Turn ignition switch ON.
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: Approx. 157.5° C (315.5°F)
OK Confirm good connection at sensor. If OK, replace EGR gas temp. sensor.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00169
ON
EGR Gas Temp.
Sensor ECM
1
2 19
9
THG E2
BE6653
FI7057
P22167 E4
E5
THG E2 5V
DI−72
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check for open in harness or ECM.
PREPARATION:
(a) Remove the instrument panel speaker No.1 panel (See
page SF−65 ).
(b) Connect between terminals THG and E2 of ECM connec-
tor.
HINT:
EGR gas temp. sensor connector is disconnected.
Before checking, do a visual check and contact pressure check
for the ECM connector (See page IN−28).
CHECK:
Read EGR gas temp. on the TOYOTA hand−held tester.
OK:
EGR gas temp.: Approx. 157.5° C (315.5°F)
OK Open in harness between terminals E2 or THG. Repair or replace harness.
NG
Confirm connection at ECM.
If OK, replace ECM (See page IN−28).
4 Check the connection of the vacuum hose, EGR hose (See page EC−11).
NG Repair or replace.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010