1996 TOYOTA LAND CRUISER egr sensor

EM−2
−
ENGINE MECHANICAL CO/HC
505
Author: Date:
1996 LAND CRUISER (RM451U)
6. TROUBLESHOOTING
If the CO/HC concentration does not comply with regulations,
troubleshoot in the order given below.
See the table below for possible causes, and then inspect and
correct the applicable causes if necessary.
COHCProblemsCauses
NormalHighRough idle
3. Faulty ignitions:
Incorrect timing
 Fouled, shorted or improperly gapped plugs
 Open or crossed high −tension cords
 Cracked distributor cap
4. Incorrect valve clearance
5. Leaky EGR valve
6. Leaky intake and exhaust valves
7. Leaky cylinders
LowHighRough idle
(Fluctuating HC reading)
1. Vacuum leaks:
 PCV hose
 EGR valve
 Intake manifold
 Air intake chamber
 Throttle body
 IAC valve
 Brake booster line
2. Lean mixture causing misfire
HighHighRough idle
(Black smoke from exhaust)
1. Restricted air filter
2. Faulty SFI systems:
 Faulty pressure regulator
 Clogged fuel return line
 Defective ECT sensor
 Faulty ECM
 Faulty injector
 Faulty throttle position sensor
 Faulty MAF meter
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM−30
−
ENGINE MECHANICAL CYLINDER HEAD
1996 LAND CRUISER (RM451U)
(b) Disconnect the connectors.
(1) Disconnect the knock sensor connector.
(2) Disconnect the oil level sensor connector.
(3) Disconnect the 2 connectors from the transmission.
(4) Disconnect the starter connector.
(c) Disconnect the 2 heated oxygen sensor connectors.
(d) Disconnect the PNP switch connector.
(e) Remove the 2 bolts and disconnect the engine wire from the intake manifold and cylinder block.
(f) Disconnect the PCV hose from the PCV valve.
(g) Remove the bolt holding the engine wire to the intake manifold.
(h) Disconnect the connectors. (1) Disconnect the connector for the emission controlvalve set assembly.
(2) Disconnect the 3 injector connectors.
(i) Disconnect the engine wire clamp.
(j) Disconnect the engine wire clamp.
(k) Disconnect the connectors.
(1) Disconnect the 3 injector connectors.
(2) Disconnect the EGR gas temp. sensor connector.
(l) Disconnect the clamp of the No. 6 injector wire from the bracket.
(m) Disconnect the engine wire from the cylinder head and in-
take manifold.
25. DISCONNECT NO. 2 WATER BYPASS PIPE
Remove the 3 bolts, and disconnect the bypass pipe from the
cylinder head.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL CYLINDER HEAD
EM−61
1996 LAND CRUISER (RM451U)
14. INSTALL HEATER PIPE
Install a new gasket, the heater pipe and ground cable with the
2 bolts and 2 nuts.
Torque:
20 N·m (200 kgf·cm, 14 ft·lbf) for bolt:
21 N·m (210 kgf·cm, 15 ft·lbf) for nut
15. INSTALL NO. 1 AND NO. 2 EXHAUST MANIFOLDS
(a) Install 2 new gaskets, No. 1 exhaust manifold and No. 2
exhaust manifold with the 13 nuts.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
(b) Install the No. 1 heat insulator and No. 2 heat insulator with the 6 bolts.
Torque: 19 N·m (195 kgf·cm, 14 ft·lbf)
16. INSTALL FRONT EXHAUST PIPE
(a) Install 2 new gaskets and the front exhaust pipe with the 4 nuts.
Torque: 63 N·m (630 kgf·cm, 46 ft·lbf)
(b) Install the No. 1 support bracket with the 2 bolts. Torque: 24 N·m (240 kgf·cm, 17 ft·lbf)
(c) Connect the clamp and tighten the clamp bolt.
Torque: 19.5 N·m (195 kgf·cm, 14 ft·lbf)
(d) Connect the front exhaust pipe to the rear TWC with a new gasket, 2 bolts and 2 nuts.
Torque: 46 N·m (470 kgf·cm, 34 ft·lbf)
17. CONNECT NO. 2 WATER BYPASS PIPE
Connect the bypass pipe to the cylinder head with the 3 bolts.
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
18. CONNECT ENGINE WIRE
(a) Place the engine wire on the intake manifold.
(b) Connect the connectors. (1) Connect the 3 injector connectors.
(2) Connect the EGR gas temp. sensor connector.
(c) Connect the clamp of the No.6 injector wire to the bracket.
(d) Connect the engine wire clamp.
(e) Connect the engine wire clamp.
(f) Connect the connectors. (1) Connect the connector for the emission control
valve set assembly.
(2) Connect the 3 injector connectors.
(g) Install the bolt holding the engine wire to the intake man- ifold.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1EN−01
SF−26
−
SFI INJECTOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT CRUISE CONTROL ACTUATOR CABLE
3. DISCONNECT ACCELERATOR CABLE
4. DISCONNECT THROTTLE CABLE
5. DISCONNECT NO.2 PCV HOSE
6. DISCONNECT AIR CLEANER HOSE
7. REMOVE EGR VACUUM MODULATOR AND VALVE (See page EC−10 )
8. REMOVE BOLT HOLDING HEATER INLET PIPE AND AIR INTAKE CHAMBER
9. DISCONNECT NO.1 PCV HOSE
10. DISCONNECT VACUUM SENSING HOSE
11. DISCONNECT NO.2 WATER BYPASS HOSE
12. DISCONNECT EVAP HOSE
13. DISCONNECT BRAKE BOOSTER HOSE
14. DISCONNECT THROTTLE POSITION SENSOR CON- NECTOR
15. DISCONNECT IDLE AIR CONTROL VALVE CONNEC-
TOR
16. DISCONNECT CONNECTOR FOR EMISSION CON- TROL VALVE SET ASSEMBLY
17. DISCONNECT EGR GAS TEMP. SENSOR CONNEC-
TOR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF−34
−
SFI INJECTOR
1996 LAND CRUISER (RM451U)
7. INSTALL INTAKE MANIFOLD STAY
Install the intake manifold stay with the 2 bolts.
Torque: 36 N·m (360 kgf·cm, 26 ft·lbf)
8. CONNECT GROUND STRAP
9. INSTALL ENGINE OIL DIPSTICK
10. CONNECT PS RESERVOIR TANK
Connect the reservoir tank with the 3 bolts. Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
11. CONNECT EGR GAS TEMP. SENSOR CONNECTOR
12. CONNECT CONNECTOR FOR EMISSION CONTROL VALVE SET ASSEMBLY
13. CONNECT IDLE AIR CONTROL VALVE CONNECTOR
14. CONNECT THROTTLE POSITION SENSOR CONNEC- TOR
15. CONNECT BRAKE BOOSTER HOSE
16. CONNECT EVAP HOSE
17. CONNECT NO.2 WATER BYPASS HOSE
18. CONNECT VACUUM SENSING HOSE
19. CONNECT NO.1 PCV HOSE
20. INSTALL BOLT HOLDING HEATER INLET PIPE AND AIR INTAKE CHAMBER
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
21. INSTALL EGR VALVE AND VACUUM MODULATOR (See page EC−10 )
22. CONNECT THROTTLE CABLE
23. CONNECT ACCELERATOR CABLE
24. CONNECT CRUISE CONTROL ACTUATOR CABLE
25. CONNECT AIR CLEANER HOSE
26. CONNECT NO.2 PCV HOSE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SF1FA−01
FI6320
Ohmmeter
Oil
−
SFI EXHAUST GAS RECIRCULATION (EGR) GAS
TEMPERATURE SENSORSF−63
691
Author: Date:
1996 LAND CRUISER (RM451U)
EXHAUST GAS RECIRCULATION
(EGR) GAS TEMPERATURE
SENSOR
INSPECTION
1. REMOVE EGR GAS TEMPERATURE SENSOR
2. INSPECT EGR GAS TEMPERATURE SENSOR
Using an ohmmeter, measure the resistance between the ter-
minals.
TemperatureResistance
50 °C (122° F)64 − 97 kΩ
100°C (212° F)11 − 16 kΩ
150 °C (302° F)2 − 4 kΩ
If the resistance is not as specified, replace the sensor.
3. REINSTALL EGR GAS TEMPERATURE SENSOR
Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EP−01
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
SS−7
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Distributor x Cylinder head1818013
No. 1 engine hanger x Cylinder head4142030
No. 2 engine hanger x Cylinder head4142030
Air intake chamber x Intake manifold2121015
Intake manifold x Cylinder head2121015
Heater inlet pipe x Intake manifold2121015
EGR pipe x Cylinder head2121015
EGR pipe x EGR valve Union nut7880058
Water outlet x Cylinder head2121015
Generator bracket x Cylinder head4344032
Cylinder head x Cylinder block 1st
2nd 3rd39
Turn 90°
Turn 90°400
Turn 90°
Turn 90°29
Turn 90°
Turn 90°
Cylinder head x Timing chain cover2121015
Camshaft bearing cap x Cylinder head1616012
Camshaft timing gear x Camshaft7475054
Chain tensioner x Cylinder head2121015
Water bypass outlet x Cylinder head2121015
Heater pipe x Timing chain cover2121015
Heater pipe x Cylinder head2020014
Exhaust manifold x Cylinder head3940029
Heat insulator x Exhaust manifold1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission2424017
No. 1 support bracket clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
No. 2 water bypass pipe x Cylinder head2020014
No. 2 water bypass pipe x No. 1 engine hanger2020014
Fuel inlet hose x Fuel filter2930022
Intake manifold stay x Air intake chamber3636026
Intake manifold stay x Cylinder block3636026
Oil dipstick guide x Intake manifold2020014
Oil dipstick guide x No. 1 oil pan2020014
PS reservoir tank x Air intake chamber2020014
Oil jet x Cylinder block2020014
Vibration damper x Cylinder block2020014
Chain tensioner slipper x Cylinder block6970051
Timing chain cover x Cylinder block2121015
Drive belt idler pulley x Timing chain cover4344032
Crankshaft pulley x Crankshaft4124,200304
Transmission housing x No. 1 oil pan7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1ES−01
−
SERVICE SPECIFICATIONS SFI
SS−11
134
Author: Date:
1996 LAND CRUISER (RM451U)
SFI
SERVICE DATA
Fuel pressure
regulatorFuel pressure at no vacuum265 − 304 kPa (2.7 − 3.1 kgf/cm2, 38 − 44 psi)
Fuel pumpResistance at 20°C (68° F)0.2 − 3.0 Ω
InjectorResistance at 20°C (68° F)
Injection volume
Difference between each cylinder
Fuel leakage13.4 − 14.2 Ω
69 − 88 cm3 (4.2 − 5.4 cu in.) per 15 sec.
5 cm3 (0.3 cu in.) or less
1 drop or less per 12 min.
MAF meterResistance (THA − E2) at −20° C (− 4°F)
at 0° C (32° F)
at 20° C (68° F)
at 40° C (104° F)
at 60° C (140° F)
at 80° C (176° F)10 − 20 kΩ
4 − 7 kΩ
2 − 3 kΩ
0.9 − 1.3 kΩ
0.4 − 0.7 kΩ
0.2 − 0.4 kΩ
Throttle bodyThrottle body fully closed angle
Dashpot setting speed
Throttle opener setting speed6°
2,200 ± 300 rpm
700 − 1,000 rpm
Throttle position
sensorClearance between stop screw and lever
0 mm (0 in.) VTA − E2
0.50 mm (0.020 in.) IDL − E2
0.75 mm (0.030 in.) IDL − E2
Throttle valve fully open VTA − E2
− VC − E2
0.2 − 5.7 kΩ
2.3 kΩ or less
Infinity
2.0 − 10.2 kΩ
2.5 − 5.9 kΩ
IAC valveResistance (B1 − S1 and S3, B2 − S2 and S4)
at cold (− 10 − 50 ° C (−50 − 122° F))
at hot (50 − 100°C (122 − 212°F))
15 − 25 Ω
20 − 30 Ω
Fuel pump resistorResistance at 20°C (68° F)0.70 − 0.76 Ω
VSV for fuel pres-
sure controlResistance at 20°C (68° F)37 − 44 Ω
ECT sensorResistance at −20° C (− 4°F)
0 °C (32° F)
20 °C (68° F)
40 °C (104° F)
60 °C (140° F)
80 °C (176° F)10 − 20 kΩ
4 − 7 kΩ
2 − 3 kΩ
0.9 − 1.3 kΩ
0.4 − 0.7 kΩ
0.2 − 0.4 kΩ
EGR gas temp
sensorResistance at 50°C (122° F)
at 100° C (212° F)
150 °C (302° F)64 − 97 kΩ
11 − 16 kΩ
2 − 4 kΩ
Heated oxygen
sensorHeater coil resistance at 20°C (68° F)11 − 16 Ω
Fuel cut rpmFuel return rpm1,200 rpm
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010