1996 TOYOTA LAND CRUISER oil

IN0CO−12
FI1066
Z11554
Seal Lock Adhesive
IN−4
−
INTRODUCTION REPAIR INSTRUCTIONS
4
Author: Date:
1996 LAND CRUISER (RM451U)
REPAIR INSTRUCTIONS
GENERAL INFORMATION
BASIC REPAIR HINT
(a) Use fender, seat and floor covers to keep the vehicle
clean and prevent damage.
(b) During disassembly, keep parts in the appropriate order to facilitate reassembly.
(c) Installation and removal of battery terminal: (1) Before performing electrical work, disconnect the
negative (−) terminal cable from the battery.
(2) If it is necessary to disconnect the battery for in- spection or repair, first disconnect the negative ( −)
terminal cable.
(3) When disconnecting the terminal cable, to prevent damage to battery terminal, loosen the cable nut
and raise the cable straight up without twisting or
prying it.
(4) Clean the battery terminals and cable ends with a clean shop rag. Do not scrape them with a file or oth-
er abrasive objects.
(5) Install the cable ends to the battery terminals after loosening the nut, and tighten the nut after installa-
tion. Do not use a hammer to tap the cable ends
onto the terminals.
(6) Be sure the cover for the positive (+) terminal is properly in place.
(d) Check hose and wiring connectors to make sure that they
are connected securely and correctly.
(e) Non−reusable parts (1) Always replace cotter pins, gaskets, O−rings, oilseals, etc. with new ones.
(2) Non−reusable parts are indicated in the component illustrations by the ” ” symbol.
(f) Precoated parts Precoated parts are bolts, nuts, etc. that are coated with
a seal lock adhesive at the factory.
(1) If a precoated part is retightened, loosened orcaused to move in any way, it must be recoated with
the specified adhesive.
(2) When reusing precoated parts, clean off the old
adhesive and dry with compressed air. Then apply
the specified seal lock adhesive to the bolt, nut or
threads.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
INTRODUCTION FOR ALL OF VEHICLES
IN−15
15
Author: Date:
1996 LAND CRUISER (RM451U)
3. FOR VEHICLES EQUIPPED WITH A CATALYTIC CONVERTER
CAUTION:
If large amount of unburned gasoline flows into the converter, it may overheat and create a fire haz-
ard. To prevent this, observe the following precautions and explain them to yo\
ur customer.
(a) Use only unleaded gasoline.
(b) Avoid prolonged idling.
Avoid running the engine at idle speed for more than 20 minutes.
(c) Avoid spark jump test. (1) Perform spark jump test only when absolutely necessary. Perform this test as rapidly as possible.
(2) While testing, never race the engine.
(d) Avoid prolonged engine compression measurement. Engine compression tests must be done as rapidly as possible.
(e) Do not run engine when fuel tank is nearly empty. This may cause the engine to misfire and create an extra load on the con\
verter.
(f) Avoid coasting with ignition turned off.
(g) Do not dispose of used catalyst along with parts contaminated with gasol\
ine or oil.
4. IF VEHICLE IS EQUIPPED WITH MOBILE COMMUNICATION SYSTEM
For vehicles with mobile communication systems such as two− way radios and cellular telephones, observe
the following precautions. (1) Install the antenna as far as possible away from the ECU and sensors of the vehicle’\
s electronic
system.
(2) Install the antenna feeder at least 20 cm (7.87 in.) away from the ECU and se\
nsors of the ve- hicle’s electronic systems. For details about ECU and sensors locations, refer\
to the section on
the applicable component.
(3) Avoid winding the antenna feeder together with other wiring as much as possible, and also avoid
running the antenna feeder parallel with other wire harnesses.
(4) Check that the antenna and feeder are correctly adjusted.
(5) Do not install powerful mobile communications system.
5. FOR USING OBD II SCAN TOOL OR TOYOTA HAND −HELD TESTER
CAUTION:
Observe the following items for safety reasons:
Before using the OBD II scan tool or TOYOTA hand −held tester, the OBD II scan tool’s instruc-
tion book or TOYOTA hand −held tester’s operator manual should be read thoroughly.
Be sure to route all cables securely when driving with the OBD II scan too\
l or TOYOTA hand −
held tester connected to the vehicle. (i.e. Keep cables away from feet,\
pedals, steering wheel
and shift lever.)
Two persons are required when test driving with the OBD II scan tool or TOYOTA hand −held
tester, one person to drive the vehicle and the other person to operate the OBD\
II scan tool or
TOYOTA hand−held tester.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2810
AC2QA−01
AC2811
N11084
Wrong Okay
LO HI LOHI
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
AC−1
1328
Author: Date:
1996 LAND CRUISER (RM451U)
AIR CONDITIONING SYSTEM
PRECAUTION
1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED
AREA OR NEAR AN OPEN FLAME
2. ALWAYS WEAR EYE PROTECTION
3. BE CAREFUL THAT LIQUID REFRIGERANT DOES NOT GET IN YOUR EYES OR ON YOUR SKIN
If liquid refrigerant gets in your eyes or on your skin:
(a) Wash the area with lots of cool water.
CAUTION:
Do not rub your eyes or skin.
(b) Apply clean petroleum jelly to the skin.
(c) Go immediately to a physician or hospital for professional treatment.
4. NEVER HEAT CONTAINER OR EXPOSE IT TO NAKED
FLAME
5. BE CAREFUL NOT TO DROP CONTAINER AND NOT TO APPLY PHYSICAL SHOCKS TO IT
6. DO NOT OPERATE COMPRESSOR WITHOUT ENOUGH REFRIGERANT IN REFRIGERANT SYSTEM
If there is not enough refrigerant in the refrigerant system oil lu-
brication will be insuf ficient and compressor burnout may occur,
so take care to avoid this.
7. DO NOT OPEN HIGH PRESSURE MANIFOLD VALVE WHILE COMPRESSOR IS OPERATING
If the high pressure valve is opened, r efrigerant flows in the re-
verse direction and could cause the charging cylinder to rup-
ture, so open and close the only low pressure valve.
8. BE CAREFUL NOT TO OVERCHARGE SYSTEM WITH
REFRIGERANT
If refrigerant is overcharged, it causes problems such as insuffi-
cient cooling, poor fuel economy, engine overheating etc.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

I01390
Condition: Insufficient cooling
I01392
Condition: Insufficient coolingNOTE : These gauge indica-
tions are shown when the
refrigeration system has
been opened and the refrig-
erant charged without vacu-
um purging.
AC−8
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
1996 LAND CRUISER (RM451U)
(6) Refrigerant overcharged or insufficient cooling of
condenser
Symptom seen in
refrigeration systemProbable causeDiagnosisRemedy
 Pressure too high on both low
and high pressure sides
 No air bubbles seen through the
sight glass even when the engine
rpm is lowered Unable to develop sufficient per-
formance due to excessive refrig-
eration system
 Insufficient cooling of condenser Excessive refrigerant in
cycle → refrigerant over charged
 Condenser cooling → condenser
fins clogged or cooling fan faulty
(1) Clean condenser
(2) Check cooling fan with fluid
coupling operation
(3) If (1) and (2) are in normal
state, check amount of refrigerant
Charge proper amount of refriger-
ant
(7) Air present in refrigeration system
Symptom seen in
refrigeration systemProbable causeDiagnosisRemedy
 Pressure too high on both low
and high pressure sides
 The low pressure piping hot to
touch
 Bubbles seen in sight glass
Air entered in refrigeration system
 Air present in refrigeration sys-
tem
 Insufficient vacuum purging
(1) Check compressor oil to see if
it is dirty or insuf ficient
(2) Evacuate air and charge new
refrigerant
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2QO−03
N06172
N14293
AC−24
−
AIR CONDITIONING COOLING UNIT
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERA TION
SYSTEM
HINT:
At the time of installation, refer to the following procedure.
Evacuate air from refrigeration system.
Charge system with refrigerant and inspect for leakage of
refrigerant.
Specified amount:
850 ± 50 g (29.98 ± 1.76 oz.)
2. DISCONNECT SUCTION TUBE AND LIQUID TUBE
FROM COOLING UNIT FITTING
Remove the 2 bolts and both tubes. Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of indtallation, lubricate 2 new O −rings with com-
pressor oil and install the tubes.
3. REMOVE THESE PARTS:
(a) Glove compratment door (See page BO−76)
(b) Glove compratment door reinforcement (See page BO−76 )
4. REMOVE COOLING UNIT
(a) Disconnect the connectors.
(b) Remove the 4 screws, 2 nuts and cooling unit.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2QP−01
N06174
Hexagonal WrenchExpansion Valve
−
AIR CONDITIONING COOLING UNIT
AC−25
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE A/C AMPLIFIER
2. REMOVE RELAY
3. REMOVE WIRE HARNESS
4. REMOVE BLOWER RESISTOR
Remove the 2 screws and blower resistor.
5. SEPARATE UPPER AND LOWER UNIT CASES
(a) Using a knife, cut off the each packing.
(b) Remove 3 clips and 4 screws.
(c) Separate the upper and lower unit cases.
6. REMOVE EVAPORATOR FROM LOWER UNIT CASE
HINT:
If the evaporator was replaced, add compressor oil to the com-
pressor.
Add 40 cc (1.4 fl.oz.)
Compressor oil:
ND−OIL 8 or equivalent
7. REMOVE THERMISTOR
Pull out the thermistor from the evaporator.
8. REMOVE EXPANSION VALVE
Using a hexagon wrench, remove the 2 bolts and separate the
expansion valve and evaporator. Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)
HINT:
At the time of reassembly, lubricate 4 new O−rings with com-
pressor oil and install the tubes.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2R5−01
N06158
−
AIR CONDITIONING COMPRESSOR AND MAGNETIC CLUTCH
AC−33
1360
Author: Date:
1996 LAND CRUISER (RM451U)
COMPRESSOR AND MAGNETIC
CLUTCH
ON−VEHICLE INSPECTION
1. INSTALL MANIFOLD GAUGE SET (See page AC−18 )
2. START ENGINE
Run the engine at 1,500 rpm.
3. INSPECT COMPRESSOR FOR METALLIC SOUND
Check if there is a metallic sound from the compressor when the
A/C switch is on.
If metallic sound is heard, replace the compressor assembly.
4. INSPECT REFRIGERANT PRESSURE (See page AC−5 )
5. STOP ENGINE
6. INSPECT VISUALLY FOR LEAKAGE OF REFRIGER- ANT FROM SAFETY SEAL
Using a gas leak detector, check for leakage of refrigerant.
If there is any leakage, replace the compressor assembly.
7. REMOVE MANIFOLD GAUGE SET (See page
AC−19 )
8. MAKE THESE VISUAL CHECKS:
(a) Leakage of grease from the clutch bearing.
(b) Signs of oil on the pressure plate or rotor. Repair or replace, as necessary.
9. INSPECT MAGNETIC CLUTCH BEARING FOR NOISE
(a) Start engine.
(b) Check for abnormal noise from near the compressor when the A/C switch is OFF.
If abnormal noise is being emitted, replace the magnetic clutch.
10. INSPECT MAGNETIC CLUTCH
(a) Disconnect the connector from the magnetic clutch.
(b) Connect the positive (+) lead from the battery to the termi-
nal on the magnetic clutch connector and the negative ( −)
lead to the body ground.
(c) Check that the magnetic clutch is energized.
If operation is not as specified, replace the magnetic clutch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2R8−01
N04963
AC−38
−
AIR CONDITIONING COMPRESSOR AND MAGNETIC CLUTCH
1996 LAND CRUISER (RM451U)
REASSEMBLY
1. INSTALL COMPRESSOR
(a) Install the compressor with the 4 bolts. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Connect the connector.
2. CONNECT DISCHARGE AND SUCTION HOSES Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)
NOTICE:
Hoses should be connected immediately after the caps
have been removed.
HINT:
Lubricate 2 new O −rings with compressor oil and install the
hoses.
3. INSTALL AND INSPECT DRIVE BELT (See page AC−17 )
4. INSTALL ENGINE UNDER COVER
5. CONNECT NEGATIVE ( −) TERMINAL CABLE TO BAT-
TERY
6. EVACUATE AIR FROM REFRIGERATION SYSTEM
7. CHARGE SYSTEM WITH REFRIGERANT AND IN- SPECT FOR LEAKAGE OF REFRIGERANT
Specified amount:
850 ± 50 g (29.98 ± 1.76 oz.)
Using a gas leak detector, check for leakage of refrigerant.
If there is leakage, check the tightening torque at the joints.
8. INSPECT A/C OPERATION
Reassembly is in the reverse order of disassembly (See
page AC−35 ).
9. CHECK CLEARANCE OF MAGNETIC CLUTCH
(a) Set the dial indicator to the pressure plate of the magnetic
clutch.
(b) Connect the magnetic clutch lead wire to the positive (+) terminal of the battery.
(c) Check the clearance between the pressure plate and ro- tor when connecting the negative ( −) terminal to the bat-
tery.
Standard clearance:
0.5 ± 0.15 mm (0.020 ± 0.0059 in.)
If the clearance is not within the standard clearance, adjust the
clearance using shims to obtain the standard clearance. Shim Thickness:
0.1 mm (0.004 in.)
0.3 mm (0.012 in.)
0.5 mm (0.020 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010