Page 936 of 1399
MA02R−04
MA−4
−
MAINTENANCE UNDER HOOD
44
Author: Date:
1996 LAND CRUISER (RM451U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTICE
Maintenance items may vary from country to country. Check the owner’s manual supplement in which
the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performe\
d.
Periodic maintenance service must be performed according to whichever interval in\
the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time inter\
val (months).
Maintenance service after the last period should be performed at the same interval \
as before unless
otherwise noted.
Failure to do even one item can cause the engine to run poorly and incre\
ase exhaust emissions.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL Check that the coolant level is between the FULL and LOW lines on the se\
e −through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leave\
s, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BATTERY ELECTROLYTE LEVEL
Check that the electrolyte level of all battery cells is between the upp\
er and lower level lines on the case.
If level is low, add distilled water only.
6. BRAKE FLUID LEVELS
Check that the brake fluid level is near the upper level line on the see\
−through reservoir.
7. ENGINE DRIVE BELTS
Check drive belt for fraying, cracks, wear or oiliness.
8. ENGINE OIL LEVEL
Check the level on the dipstick with the engine turned off.
9. POWER STEERING FLUID LEVEL
(a) Check the level on the dipstick.
(b) The level should be in the HOT or COLD range depending on the fluid temp\
erature.
10. AUTOMATIC TRANSMISSION FLUID LEVEL
(a) Park the vehicle on a level surface.
(b) With the engine idling and the parking and foot brake applied, shift the sel\
ector into all positions from the P to L, and then shift into the P.
(c) Pull out the dipstick and wipe off the fluid with a clean rag. Re −insert the dipstick fully and check that
the fluid level is in the HOT range.
(d) Do this check with the fluid at normal driving temperature (70 − 80°C (158 − 176° F)).
HINT:
Wait about 30 minutes before checking the fluid level after extended driving\
at high speeds in hot weather,
driving in heavy traffic or with a trailer.
11. EXHAUST SYSTEM
Visually inspect for cracks, holes or loose supports.
If any change in the sound of the exhaust or smell of the exhaust fumes is\
noticed, have the cause located
and corrected.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1002 of 1399
PP2YN−01
−
PREPARATION STEERING
PP−61
1996 LAND CRUISER (RM451U)
LUBRICANT
ItemCapacityClassification
Power steering fluid Total0.8 liters (0.9 US qts, 0.7 lmp. qts)ATF DEXRON® II or III
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1255 of 1399
SR165−01
SR−2
−
STEERING TROUBLESHOOTING
1053
Author: Date:
1996 LAND CRUISER (RM451U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers \
indicate the priority of the likely
cause of the problem. Check each part in the order shown. If necessary, repair or replace these parts.
SymptomSuspect AreaSee page
Hard steering
11. Tires (Improperly inflated)
12.Power steering fluid level (Low)
13.Front wheel alignment (Incorrect)
14.Steering system joints (Worn)
15.Suspension arm ball joints (W orn)
16.Steering column (Binding)
17.Power steering vane pump
18.Power steering gearSA−3
SR−4 SA−4 −
−
−
SR−21
SR−33
Poor return
1. Tires (Improperly inflated)
2. Front wheel alignment (Incorrect)
3. Steering column (Binding)
4. Power steering gearSA−3
SA−4 −
SR−33
Excessive play
1. Steering system joints (Worn)
2. Suspension arm ball joints (W orn)
3. Intermediate shaft, Universal joint, Sliding yoke (Worn)
4. Front wheel bearing (W orn)
5. Power steering gear−
−
−
SR−7
SR−33
Abnormal noise
1. Power steering fluid level (Low)
2. Steering system joints (Worn)
3. Power steering vane pump
4. Power steering gearSR−4 −
SR−21
SR−33
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1256 of 1399
SR167−01
R07281
Normal
Abnormal
−
STEERING POWER STEERING FLUID
SR−3
1054
Author: Date:
1996 LAND CRUISER (RM451U)
POWER STEERING FLUID
BLEEDING
1. CHECK FLUID LEVEL (See page SR−4 )
2. JACK UP FRONT OF VEHICLE AND SUPPORT IT WITH STANDS
3. TURN STEERING WHEEL
With the engine stopped, turn the wheel slowly from lock to lock
several times.
4. LOWER VEHICLE
5. START ENGINE
Run the engine at idle for a few minutes.
6. TURN STEERING WHEEL
(a) With the engine idling, turn the wheel to left or right full lock and keep it there for 2 −3 seconds, then turn the
wheel to the opposite full lock and keep it there for 2 −3 se-
conds.
(b) Repeat (a) several times.
7. STOP ENGINE
8. CHECK FOR FOAMING OR EMULSIFICATION
If the system has to be bled twice specifically because of foam-
ing or emulsification, check for fluid leaks in the system.
9. CHECK FLUID LEVEL (See page SR−4)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1257 of 1399
SR166−01
R07281
Normal Abnormal
SR−4
−
STEERING POWER STEERING FLUID
1996 LAND CRUISER (RM451U)
INSPECTION
1. CHECK FLUID LEVEL
(a) Keep the vehicle level.
(b) With the engine stopped, check the fluid level in the oil reservoir.
If necessary, add fluid.
Fluid: ATF DEXRON® II or III
HINT:
Check that the fluid level is within the HOT LEVEL range on the
reservoir cap dipstick. If the fluid is cold, check that it is within
the COLD LEVEL range.
(c) Start the engine and run it at idle.
(d) Turn the steering wheel from lock to lock several times to
boost fluid temperature.
Fluid temperature: 80° C (176°F)
(e) Check for foaming or emulsification.
If there is foaming or emulsification, bleed power steering sys-
tem. (See page SR−3 ).
(f) With the engine idling, measure the fluid level in the oil reservoir.
(g) Stop the engine.
(h) Wait a few minutes and remeasure the fluid level in the oil reservoir.
Maximum fluid level rise: 5 mm (0.20 in.)
If a problem is found, bleed power steering system (See page
SR−3 ).
(i) Check the fluid level.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1258 of 1399
Z15498
PS GearClosed
SST PS Vane
Pump
Oil
Reservoir
−
STEERING POWER STEERING FLUID
SR−5
1996 LAND CRUISER (RM451U)
2. CHECK STEERING FLUID PRESSURE
(a) Disconnect the pressure feed tube from the PS vane
pump (See page SR−23).
(b) Connect SST over 2 new gaskets, as shown below. SST 09640 −10010 (09641 −01010, 09641 −01030,
09641 −01060)
NOTICE:
Check that the valve of the SST is in the open position.
(c) Bleed the power steering system (See page SR−3).
(d) Start the engine and run it at idle.
(e) Turn the steering wheel from lock to lock several times to
boost fluid temperature.
Fluid temperature: 80° C (176°F)
(f) With the engine idling, close the valve of the SST and ob-
serve the reading on the SST.
Minimum fluid pressure:
9,316kPa (95 kgf/cm
2, 1,351 psi)
NOTICE:
Do not keep the valve closed for more than 10 se-
conds.
Do not let the fluid temperature become too high.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1259 of 1399
Z15499
PS GearSSTPS Vane
Pump
Oil
Reservoir
Open
Z15500
PS Gear
SSTPS Vane
Pump
Oil
Reservoir
Open
Lock Position
SR−6
−
STEERING POWER STEERING FLUID
1996 LAND CRUISER (RM451U)
(g) With the engine idling, open the valve fully.
(h) Measure the fluid pressure at engine speeds of 1,000 rpm
and 3,000 rpm.
Difference fluid pressure:
490 kPa (5 kgf/cm
2, 71 psi) or less
NOTICE:
Do not turn the steering wheel.
(i) With the engine idling and valve fully opened, turn the steering wheel to full lock.
Minimum fluid pressure:
9,316 kPa (95 kgf/cm
2, 1,351 psi)
NOTICE:
Do not maintain lock position for more than 10 se-
conds.
Do not let the fluid temperature become too high.
(j) Disconnect the SST.
(k) Connect the pressure feed tube (See page SR−32).
(l) Bleed the power steering system (See page SR−3).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1279 of 1399
V08067
Rotor
markCam ring
mark Vane plate part
number Vane plate length
mm (in.)
14.995 − 14.997
(0.59035 − 0.59043)
44345
−60030
2
None
1 3 44345
−60040 14.993
− 14.995
(0.59027 − 0.59035)
14.991 − 14.993
(0.59020 − 0.59027)
44345
−60050
4
2
R08078
SR3776
Compressed Air
R08702
SR−28
−
STEERING POWER STEERING VANE PUMP
1996 LAND CRUISER (RM451U)
HINT:
There are 3 vane plate lengths for the following rotor and cam
ring marks.
3. INSPECT FLOW CONTROL VALVE
(a) Coat the valve with power steering fluid and check that it
falls smoothly into the valve hole by its own weight.
(b) Check the valve for leakage. Close one of the holes and apply 392 − 490 kPa (4 − 5 kgf/cm
2, 57 − 71 psi) of com-
pressed air into the opposite side, and confirm that air
does not come out from the end holes.
Inscribed mark:
A, B, C, D, E or F
4. INSPECT SPRING
Using calipers, measure the free length of the spring. Minimum free length: 35 − 37 mm (1.38 − 1.46 in.)
If it is not within the specification, replace the spring.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
