1996 TOYOTA LAND CRUISER Engine oil level

AT0TB−01
Q08463
Hold Down ClampBattery
Battery Tray
Starter
Fan Shroud
Level Gauge Front Propeller Shaft
Oil Filler Pipe
 Gasket
 Hole Plug
O− Ring
Engine Under Cover Stabilizer BarCrossmember with
Transfer Under Cover
 Non− reusable Part 
 Gasket

AT
−18
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
802
Author: Date:
1996 LAND CRUISER (RM451U)
AUTOMATIC TRANSMISSION UNIT
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−5
1996 LAND CRUISER (RM451U)
Fuel gauge does not operate or abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32
−
Engine coolant temperature gauge does not operation or
abnormal operate.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32−
Oil pressure gauge does not operate or abnormal operation.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−34−
All illumination lights do not light up.
1. TAIL Fuse (I/P F/B)
2. Light Control Rheostat
3. Wire Harness−
BE−34 −
Brightness does not change even when rheostat turned.1. Bulb
2. Wire Harness−
−
Only one illumination light does not light up.1. Bulb
2. Wire Harness−
−
WARNING LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
Warning lights do not lights up.
(Except discharge, SRS and door open)1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Brake warning light does not light up.
1. Bulb
2. Brake Fluid Level Switch
3. Parking Brake Switch
4. Meter Circuit
5. Wire Harness−
BE−34
BE−34
BE−32 −
Open door warning light does not light up.
1. Bulb
2. Door Courtesy Switch
3. DOME Fuse (No.2 R/B)
4. Meter Circuit
5. Wire Harness−
BE−21
BE−21 −
−
−
SRS warning light does not light up
1. Bulb
2. Airbag Sensor Assembly
3. ECU− B Fuse (I/P F/B)
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Discharge warning light does not light up.
1. Bulb
2. IGN Fuse (No.1 J/B)
3. Generator
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Seat belt warning light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Seat Belt Warning Relay (I/P F/B)
4. Meter Circuit
5. Wire Harness−
BE−34 −
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−6
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Engine oil level warning light does not light up.
1. Bulb
2. Meter Circuit
3. Engine Oil Level Warning Switch
4. Wire Harness−
BE−32
BE−34 −
Low oil pressure warning light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−32
BE−34 −
Fuel level warning light does not light up.
1. Bulb
2. Fuel Level Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−34
BE−32 −
INDICATOR LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
High beam indicator light does not light up.
1. Bulb
2. Headlight and Taillight System
3. Meter Circuit
4. Wire Harness−
BE−19
BE−32 −
Shift indicator lights do not light up. (ALL)
1. Shift Position Indicator Wiring Circuit
2. Park/Neutral Position Switch
3. Wire Harness
4. Bulb−
BE−34 AT −6
−
Shift indicator lights do not light up. (L, 2, D)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Park/Neutral Position Switch
4. Light Control Rheostat
5. Wire Harness−
BE−34 AT −6
BE−34 −
Shift indicator lights do not light up. (PWR)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Pattern Select Switch
4. Wire Harness−
BE−34 AT −6
−
Shift indicator lights do not light up. (2nd START)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. ECM
4. Wire Harness−
AT −6
−
−
Only one shift indicator does not light up.1. Bulb
2. Shift Position Indicator Wiring Circuit−
BE−34
Indicator lights do not light up. (Except Turn, Hi −beam)1. GAUGE Fuse (I/P F/B)
2. Wire Harness−
−
O/D OFF indicator light does not light up.
1. Bulb
2. O/D Main Switch
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Malfunction indicator light does not light up.
1. Bulb
2. ECM
3. Wire Harness−
−
−
Cruise control indicator light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE4917
Test LED
Battery
BE1217
Warning Light
Ignition
Switch Battery
N01212
BE−38
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
(c) Ground terminal on the wire harness side through a 3.4
W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and that the receiver gauge needle moves to the high
side.
If operation is not as specified, measure the receiver gauge re-
sistance.
14. INSPECT OIL PRESSURE RECEIVER GAUGE RESIS- TANCE
Measure the receiver gauge resistance between terminals. Resistance:
40 − 48 Ω
If resistance value is not as specified, replace the receiver
gauge.
15. INSPECT OIL PRESSURE SENDER GAUGE OPERA-
TION
(a) Disconnect the connector from the sender gauge.
(b) Apply battery positive voltage to the sender gauge termi- nal through a test LED.
(c) Check that the bulb does not light when the engine is stopped.
(d) Check that the LED flashes when the engine is running. The number of flashed should vary with engine speed.
If operation is not as specified, replace the sender gauge.
16. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connectors from the level warning switch and parking brake switch.
(b) Connect terminals on the wire harness side connector of
the level warning switch connector.
(c) Turn the ignition switch ON, and check that the warning light lights up.
17. INSPECT PARKING BRAKE SWITCH
(a) Check that there is continuity between terminal and the switch set nut with switch pin released (parking brake le-
ver pulled up).
(b) Check that there is no continuity between terminal and the switch set nut with switch pin pushed in. (parking
brake lever released)
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−40
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
23. INSPECT SEAT BELT WARNING RELAY CIRCUIT
Disconnect the connector from the relay and inspect the con-
nector on the wire harness side, as shown in the chart.
Tester connectionConditionSpecified condition
1 − GroundConstantContinuity
4 − GroundDriver’s seat belt position UNFASTENContinuity
4 − GroundDriver’s seat belt position FASTENNo continuity
7 − GroundIgnition key SETContinuity
7 − GroundIgnition key RemoveNo continuity
8 − GroundDriver’s door position OPENContinuity
8 − GroundDriver’s door position CLOSENo continuity
5 − GroundIgnition switch position ONBattery positive voltage
5 − GroundIgnition switch position LOCK or ACCNo voltage
9 − GroundConstantBattery positive voltage
If circuit is as specified, try another relay.
If the circuit is not as specified, check the circuits connected to
other parts.
24. INSPECT ENGINE OIL LEVEL WARNING SWITCH
(a) Check that there is continuity between terminal with the
switch each position.
(b) Heat the switch to above 60° C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06300
BrightDark 2
3
Extinguished
1
−
BODY ELECTRICAL COMBINATION METER
BE−41
1996 LAND CRUISER (RM451U)
25. INSPECT ENGINE OIL LEVEL WARNING CIRCUIT
Disconnect the switch connector and inspect the connector on
wire harness side, as shown.
Tester connectionConditionSpecified condition
2 − GroundConstantContinuity
If continuity is not as specified, inspect the wire harness or
ground point.
26. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON, and check that the warning
light lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
27. INSPECT LIGHT CONTROL RHEOSTAT
(a) Connect terminals 1 and 3 through a 3.4 W test bulb.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2.
(c) Turn the rheostat knob to fully counterclockwise, and
check that the test bulb goes out.
(d) Gradually turn the rheostat knob to clockwise, and check
that the test bulb brightness changes from dark to bright.
If operation is not as specified, replace the rheostat.
HINT:
Adjust the brightness of illumination lights by rheostat.
A/C Control Assembly
Antenna Switch
Ash Receptacle
Audio
Center Diff. Lock Switch
Cigarette Lighter
Defogger Switch
Hazard Warning Switch
Shift Lever
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO0IO−04
−
COOLING COOLANT
CO−1
696
Author: Date:
1996 LAND CRUISER (RM451U)
COOLANT
INSPECTION
HINT:
Check the coolant level when the engine is cold.
1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR
The engine coolant level should be between the ”LOW” and ”FULL”\
lines.
If low, check for leaks and add engine coolant up to the ”FULL” line.
2. CHECK ENGINE COOLANT QUALITY
(a) Remove the radiator cap.
CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator
are still hot, as fluid and steam can be blown out under pressure.
(b) There should not be any excessive deposits of rust or scale around the r\
adiator cap or radiator filler
hole, and the coolant should be free from oil.
If excessively dirty, replace the coolant.
(c) Reinstall the radiator cap.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO118−01
CO−16
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL RADIATOR
(a) Install the 2 radiator brackets with the 4 nuts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Install the radiator with the 2 bolts and 2 nuts. Torque:
Bolt: 18 N·m (185 kgf·cm, 13 ft·lbf)
Nut: 12 N·m (120 kgf·cm, 9 ft·lbf)
2. CONNECT A/T OIL COOLER HOSES
3. CONNECT RADIATOR OUTLET HOSE
4. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(b) Temporarily install the fan pulley mounting nuts.
(c) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(d) Connect the oil cooler hose to the clamp on the fan
shroud.
(e) Install the drive belts with the adjusting bolt and pivot bolt.
(f) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(g) Adjust the drive belts (See page CH−2 ).
5. CONNECT RADIATOR RESERVOIR HOSE
6. CONNECT RADIATOR INLET HOSE
7. CONNECT NO.3 WATER BYPASS HOSE
8. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
9. INSTALL BATTERY AND BATTERY TRAY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery with the hold−down clamp and nuts.
(d) Connect the battery cables.
10. FILL RADIATOR WITH ENGINE COOLANT
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010