1996 TOYOTA LAND CRUISER tachometer

IN−36
−
INTRODUCTION TERMS
36
Author: Date:
1996 LAND CRUISER (RM451U)
NA
Natural Aspiration
No.Number
O/DOverdrive
OEMOriginal Equipment Manufacturing
OHCOverhead Camshaft
OHVOverhead V
alve
OPTOption
O/SOversize
P & BVProportioning And Bypass Valve
PCSPower Control System
PCVPositive Crankcase Ventilation
PKBParking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take−Off
R & PRack And Pinion
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight−Hand
RHDRight−Hand Drive
RLYRelay
ROMRead Only Memory
RrRear
RRRear−Engine Rear −Wheel Drive
RRSRigid Rear Suspension
RWDRear− Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SMTSequential Manual T ransmission
SOCState Of Charge
SOHCSingle Overhead Camshaft
SPECSpecification
SPISingle Point Injection
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
STJCold−Start Fuel Injection
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TBIThrottle Body Electronic Fuel Injection
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−4
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Back−
Up light remains on.
1. Park/Neutral Position Switch (A/T)
2. Wire Harness−
−
Only one light does not light up.1. Bulb
2. Wire Harness−
−
STOP LIGHT SYSTEM
SymptomSuspect AreaSee page
Stop light does not light up.
1. STOP Fuse (I/P F/B)
2. Stop Light Switch
3. Bulb
4. Wire Harness−
BE−25 −
−
Stop light remains always on.1. Stop Light Switch
2. Wire HarnessBE−25−
Only one light does not light up.1. Wire Harness
2. Bulb−
−
WIPER AND WASHER SYSTEM
SymptomSuspect AreaSee page
Wipers do not operate or return to off position.
1. WIPER Fuse (I/P F/B)
2. Wiper Switch
3. Wiper Motor
4. Wiper Relay
5. Wire HarnessBE−27
BE−27
BE−27
BE−27
−
Wipers do not operate in MIST.
1. Wiper Switch
2. Wiper Motor
3. Wiper Relay
4. Wire HarnessBE−27
BE−27
BE−27
−
Wipers do not operate in INT.
1. Wiper Switch
2. Wiper Motor
3. Wiper Relay
4. Wire HarnessBE−27
BE−27
BE−27−
Washer does not operate.
1. Washer Hose or Nozzle Clogged
2. Washer Switch
3. Washer Motor
4. Wire Harness−
BE−27
BE−27 −
METER, GAUGES AND ILLUMINATION:
COMBINATION METER
SymptomSuspect AreaSee page
Tachometer, speedometer, engine coolant temperature gauge and
fuel gauge do not operate.1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Speedometer does not operate.
1. No.1 Vehicle Speed Sensor
2. Speedometer Driven Gear and Drive Gear
3. Meter Circuit
4. Wire HarnessBE−34−
BE−32 −
Tachometer does not operate.
1. Meter Circuit
2. Igniter
3. Wire HarnessBE−32−
−
Tachometer does not operate.
1. Meter Circuit
2. Igniter
3. Wire HarnessBE−32−
−
Voltmeter does not operate.1. Voltmeter Receiver Gauge
2. Wire HarnessAT −6
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MD−01
BE−34
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SPEEDOMETER ON−VEHICLE:
Using a speedometer tester, inspect the speedometer for allow-
able indication error and check the operation of the odometer.
HINT:
Tire wear and tire over or under inflation will increase the indica-
tion error.
If error is excessive, replace the speedometer.
Standard indicationAllowable range
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
120118 − 132
2. INSPECT NO.1 VEHICLE SPEED SENSOR OPERA-
TION
(a) Connect the positive (+) lead from battery to terminal 1 and negative ( −) lead to terminal 2.
(b) Connect the positive (+) lead from tester to terminal 3 and
the negative ( −) lead to terminal 2.
(c) Revolve shaft.
(d) Check that there is voltage changer from approx. 0 V to 11 V or more between terminals 3 and 2.
HINT:
The voltage change should be 4 times per each revolution of
the No.1 vehicle speed sensor shaft.
If operation is not as specified, replace the sensor.
3. INSPECT TACHOMETER ON−VEHICLE:
(a) Connect a tune− up test tachometer, and start the engine.
NOTICE:
Reversing the connection of the tachometer will damage
the transistors and diodes inside.When removing or instal-
ling the tachometer, be careful not to drop or subject it to
heavy shocks.
(b) Compare the tester and tachometer indications.
If error is excessive, replace the tachometer.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1E0−04
−
ENGINE MECHANICAL CO/HC
EM−1
504
Author: Date:
1996 LAND CRUISER (RM451U)
CO/HC
INSPECTION
HINT:
This check is used only to det ermine whether or not the idle CO/
HC complies with regulations.
1. INITIAL CONDITIONS
(a) Engine at normal operating temperature
(b) Air cleaner installed
(c) All pipes and hoses of air induction system connected
(d) All accessories switched OFF
(e) All vacuum lines properly connected
HINT:
All vacuum hoses for EGR systems, etc. should be properly
connected.
(f) SFI system wiring connectors fully plugged
(g) Ignition timing set correctly
(h) Transmission in neutral position
(i) Tachometer and CO/HC meter calibrated by hand
2. START ENGINE
3. RACE ENGINE AT 2,500 RPM FOR APPROX. 180 SE-
CONDS
4. 4.INSERT CO/HC METER TESTING PROBE AT LEAST
40 cm (1.3 ft) INTO TAILPIPE DURING IDLING
5. IMMEDIATELY CHECK CO/HC CONCENTRATION AT IDLE AND/OR 2,500 RPM
HINT:
When doing the 2 mode (2,500 rpm and idle) test, follow the
measurement order prescribed by the applicable local regula-
tions.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EJ−02
SS−40
−
SERVICE SPECIFICATIONS BODY ELECTRICAL
163
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL
SERVICE DATA
TURN SIGNAL FLASHER
Flashes/Minute60 − 120
SPEEDOMETER (USING A SPEEDOMETER)
Standard indication (mph)Allowable range (mph)
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
12011 8 − 132
TACHOMETER (ON− VEHICLE) DC 13.5 V 25°C (77° F)
Standard indication (RPM)Allowable range (RPM)
700630 − 770
1,000900 − 1,100
2,0001,875 − 2,125
3,0002,850 − 3,150
4,0003,850 − 4,150
5,0004,850 − 5,150
FUEL RECEIVER GAUGE
A − B85.5 − 105.5 Ω
A − C126 − 150 Ω
B − C90 − 110 Ω
FUEL SENDER GAUGE
Float position F: Approx. 15 mm ((0.59 in.)Approx. 3 Ω
Float position E: Approx. 200 (7.87 in.)Approx. 110 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE
A − B71 − 79 Ω
A − C117 − 141 Ω
B − C185 − 215 Ω
OIL PRESSURE RECEIVER GAUGE
Resistance40 − 48 Ω
CRUISE CONTROL SWITCH
Switch position OFFNo continuity
Switch position RESUME/ACCELApprox. 68 Ω
Switch position SET/COASTApprox. 198 Ω
Switch position CANCELApprox. 418 Ω
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2 kΩ
2 − 3Approx. 0.5 − 1.7 kΩ
Actuator control arm free play0 mm (0 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010