1996 TOYOTA LAND CRUISER Battery terminals

IN0CO−12
FI1066
Z11554
Seal Lock Adhesive
IN−4
−
INTRODUCTION REPAIR INSTRUCTIONS
4
Author: Date:
1996 LAND CRUISER (RM451U)
REPAIR INSTRUCTIONS
GENERAL INFORMATION
BASIC REPAIR HINT
(a) Use fender, seat and floor covers to keep the vehicle
clean and prevent damage.
(b) During disassembly, keep parts in the appropriate order to facilitate reassembly.
(c) Installation and removal of battery terminal: (1) Before performing electrical work, disconnect the
negative (−) terminal cable from the battery.
(2) If it is necessary to disconnect the battery for in- spection or repair, first disconnect the negative ( −)
terminal cable.
(3) When disconnecting the terminal cable, to prevent damage to battery terminal, loosen the cable nut
and raise the cable straight up without twisting or
prying it.
(4) Clean the battery terminals and cable ends with a clean shop rag. Do not scrape them with a file or oth-
er abrasive objects.
(5) Install the cable ends to the battery terminals after loosening the nut, and tighten the nut after installa-
tion. Do not use a hammer to tap the cable ends
onto the terminals.
(6) Be sure the cover for the positive (+) terminal is properly in place.
(d) Check hose and wiring connectors to make sure that they
are connected securely and correctly.
(e) Non−reusable parts (1) Always replace cotter pins, gaskets, O−rings, oilseals, etc. with new ones.
(2) Non−reusable parts are indicated in the component illustrations by the ” ” symbol.
(f) Precoated parts Precoated parts are bolts, nuts, etc. that are coated with
a seal lock adhesive at the factory.
(1) If a precoated part is retightened, loosened orcaused to move in any way, it must be recoated with
the specified adhesive.
(2) When reusing precoated parts, clean off the old
adhesive and dry with compressed air. Then apply
the specified seal lock adhesive to the bolt, nut or
threads.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE2826
Cassette Tape Slot Cover
IN−16
−
INTRODUCTION FOR ALL OF VEHICLES
16
Author: Date:
1996 LAND CRUISER (RM451U)
6. FOR VEHICLES WITH AN AUDIO SYSTEM WITH
BUILT−IN ANTI−THEFT SYSTEM
Audio System displaying the sign ANTI −THEFT SYSTEM
shown on the left has a built −in anti −theft system which makes
the audio system soundless if stolen.
If the power source for the audio system is cut even once, the
anti0theft system operates so that even if the power source is
reconnected, the audio system will not produce any sound un-
less the ID number selected by the customer is input again. Ac-
cordingly, when performing repairs on vehicles equipped with
this system, before disconnecting the battery terminals or re-
moving the audio system the customer should be asked for the
ID number afterwards, or else a request made to the customer
to input the ID number. For the method to input the ID number
or cancel the anti−theft system, refer to the Owner’s Manual.
ANTI-THEFTSYSTEM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z16656
BC
KLS
E
STP SLS−
ACC
IG A
SLS+
AT0T7−04
Q07316
Ohmmeter
Q07315Battery
−
AUTOMATIC TRANSMISSION SHIFT LOCK SYSTEM
AT−13
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SHIFT LOCK CONTROL ECU
Using a voltmeter, measure the voltage at each terminal.
HINT:
Do not disconnect the ECU connector.
2. INSPECT SHIFT LOCK SOLENOID
(a) Disconnect the solenoid connector.
(b) Using an ohmmeter, measure the resistance between ter-
minals.
Standard resistance: 20 − 28 Ω
If the resistance is not as specified, replace the solenoid.
(c) Apply the battery positive voltage between terminals. At this time, confirm that solenoid operate.
If the operation is not as specified, replace the solenoid.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE27G−01
BE1843
−
BODY ELECTRICAL TURN SIGNAL AND HAZARD WARNING SYSTEM
BE−19
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT HAZARD WARNING SWITCH CONTINUITY
ConditionTester connectionSpecified condition
Switch OFF7 − 10Continuity
Switch ON7 − 8
4 − 5 − 6 − 9Continuity
Illumination circuit2 − 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT TURN SIGNAL FLASHER OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative ( −) lead to terminal 3.
(b) Connect the 2 turn signal light bulbs parallel to each other
to terminals 1 and 3, and check that the bulbs flash.
HINT:
The turn signal lights should flash 60 to 120 times per minute.
If one of the front or rear turn signal lights has an open circuit,
the number of flashes will be more than 140 per minute.
If operation is not as specified, replace the flasher.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

V02744
3.3 ± 1 sec.
Battery Positive Voltage
B7B16
B18
V02745
Washer Switch ON
OFF Approx.
0.5 sec.
Battery-
positive
voltage Approx. 2.5 sec.
0 V
BE−28
−
BODY ELECTRICAL WIPER AND WASHER SYSTEM
1996 LAND CRUISER (RM451U)
If operation is not as specified, replace the switch.
4. INSPECT WASHER LINKED OPERATION
(a) Connect the positive (+) lead from the battery to terminal
B18 and the negative ( −) lead to terminal B16.
(b) Connect the positive (+) lead from the voltmeter to termi- nal B7 and the negative ( −) lead to terminal B16.
(c) Push in the washer switch. Check that the voltage
changes, as shown in the table.
If operation is not as specified, replace the switch.
5. INSPECT REAR WIPER RELAY CONTINUITY
(a) Check that there is no continuity between terminals 1 and
3.
(b) Check that there is continuity between terminals 2 and 3.
If continuity is not as specified, replace the relay.
6. INSPECT REAR WIPER RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 6.
(b) Connect the positive (+) lead from the voltmeter to termi- nal 2 and the negative ( −) lead to terminal 6, and check
that the meter needle indicates to O V.
(c) Connect the positive (+) lead from the voltmeter to termi-
nal 3 and the negative ( −) lead to terminal 6, and check
that the meter needle indicates to battery positive voltage.
If operation is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1MD−01
BE−34
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SPEEDOMETER ON−VEHICLE:
Using a speedometer tester, inspect the speedometer for allow-
able indication error and check the operation of the odometer.
HINT:
Tire wear and tire over or under inflation will increase the indica-
tion error.
If error is excessive, replace the speedometer.
Standard indicationAllowable range
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
120118 − 132
2. INSPECT NO.1 VEHICLE SPEED SENSOR OPERA-
TION
(a) Connect the positive (+) lead from battery to terminal 1 and negative ( −) lead to terminal 2.
(b) Connect the positive (+) lead from tester to terminal 3 and
the negative ( −) lead to terminal 2.
(c) Revolve shaft.
(d) Check that there is voltage changer from approx. 0 V to 11 V or more between terminals 3 and 2.
HINT:
The voltage change should be 4 times per each revolution of
the No.1 vehicle speed sensor shaft.
If operation is not as specified, replace the sensor.
3. INSPECT TACHOMETER ON−VEHICLE:
(a) Connect a tune− up test tachometer, and start the engine.
NOTICE:
Reversing the connection of the tachometer will damage
the transistors and diodes inside.When removing or instal-
ling the tachometer, be careful not to drop or subject it to
heavy shocks.
(b) Compare the tester and tachometer indications.
If error is excessive, replace the tachometer.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−36
−
BODY ELECTRICAL COMBINATION METER
1996 LAND CRUISER (RM451U)
7. INSPECT FUEL SENDER GAUGE OPERATION
(a) Connect a series of three 1.5 V dry cell batteries.
(b) Connect the positive (+) lead from the dry cell batteries to
terminal 4 through a 3.4 W test bulb and the negative ( −)
lead to terminal 5.
(c) Connect the positive (+) lead from the voltmeter to termi- nal 4 and the negative ( −) lead to terminal 5.
(d) Check that the voltage rises as the float is moved from the
full to empty position.
8. INSPECT FUEL SENDER GAUGE RESISTANCE
Measure the resistance between terminals 4 and 5.
Float position: mm (in.)Resistance (Ω )
F: Approx. 15.0 (0.591)Approx. 3.0
E: Approx. 200.0 (7.874)Approx. 110.0
If resistance value is not as specified, replace the sender
gauge.
9. INSPECT FUEL LEVEL WARNING LIGHT
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 1 and 5 on the wire harness side con-
nector.
(c) Turn the ignition switch ON, and check that the warning
light lights up.
If the warning light does not light up, test the bulb.
10. INSPECT FUEL LEVEL WARNING SWITCH
(a) Apply battery positive voltage between terminals 1 and 5
through a 3.4 W test bulb, and check that the bulb lights
up.
HINT:
It will take a short time for the bulb to light up.
(b) Submerge the switch in fuel, and check that the bulb goes
out.
If operation is not as specified, replace the sender gauge.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Engine Coolant
Temperature
Gauge
Ignition Switch
Battery Sender
Gauge
Z06815
Engine
Coolant T emperature Gauge
Ignition
Switch Tester Bulb
(3.4 W)
Battery
BE1222
Oil Pressure Gauge
Ignition
Switch Sender
Gauge
Battery
−
BODY ELECTRICAL COMBINATION METER
BE−37
1996 LAND CRUISER (RM451U)
11. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates COOL.
(c) Ground terminal on the wire harness side connector through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights up and the receiver gauge needle moves to the hot side.
If operation is as specified, replace the sender gauge. Then re-
check the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
12. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
Between terminalsResistance (Ω )
A − B71 − 79
A − C117 − 141
B − C185 − 215
HINT:
Connect the test leads so that the current from the ohmmeter
can flow according to the above order. This circuit include the
diode.
If resistance value is not as specified, replace the receiver
gauge.
13. INSPECT OIL PRESSURE RECEIVER GAUGE OP-
ERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON, and check that the receiver
gauge needle indicates LOW.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010