1996 TOYOTA LAND CRUISER Fuse a

BE1367
Medium Current Fuse and High Current Fuse
Equal Amperage Rating
V00076
Abbreviation
Part Name
Symbol
Illustration
FUSE
MEDIUM CURRENT FUSE
HIGH CURRENT FUSE
FUSIBLE LINK
CIRCUIT BREAKER FUSE
M−FUSE
H−FUSE
FL
CB
−
INTRODUCTION REPAIR INSTRUCTIONS
IN−5
5
Author: Date:
1996 LAND CRUISER (RM451U)
(3) Precoated parts are indicated in the component il-
lustrations by the ” ” symbol.
(g) When necessary, use a sealer on gaskets to prevent
leaks.
(h) Carefully observe all specifications for bolt tightening torques. Always use a torque wrench.
(i) Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found in Preparation section in this
manual.
(j) When replacing fuses, be sure the new fuse has the cor- rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.
~
iJ<>~o~BE5594 IN0365
~
~
BE5595IN0366
~
~
BE5596IN0367
~
~
BE5597IN0367
~BE5598SN0368
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
INTRODUCTION TERMS
IN−35
35
Author: Date:
1996 LAND CRUISER (RM451U)
H/B
Hatchback
H−FUSEHigh Current Fuse
HIHigh
HIDHigh Intensity Discharge (Head Lamp)
HPUHydraulic Power Unit
HSGHousing
HTHard Top
HWSHeated Windshield System
IACIdle Air Control
ICIntegrated circuit
IDIIndirect Diesel Injection
IFSIndependent Front Suspension
IGIgnition
IIAIntegrated Ignition Assembly
INIntake (Manifold, V
alve)
INTIntermittent
I/PInstrument Panel
IRSIndependent Rear Suspension
J/BJunction Block
J/CJunction Connector
KDKick−Down
LANLocal Area Network
LBLiftback
LCDLiquid Crystal Display
LEDLight Emitting Diode
LHLeft−Hand
LHDLeft−Hand Drive
L/H/WLength, Height, Width
LLCLong− Life Coolant
LNGLiquified Natural Gas
LOLow
LPGLiquified Petroleum Gas
LSDLimited Slip Dif ferential
LSP & PVLoad Sensing Proportioning And Bypass V alve
LSPVLoad Sensing Proportioning Valve
MAX.Maximum
M−FUSEMedium Current Fuse
MICMicrophone
MILMalfunction Indicator Lamp
MIN.Minimum
MPMultipurpose
MPXMultiplex Communication System
M/TManual Transmission (T ransaxle)
MTMount
MTGMounting
NNeutral
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC2QC−03
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
AC−3
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem.The numbers i\
ndicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
No blower operation
4. HTR Fuse
5. Heater main relay
6. Blower motor
7. Blower resistor
8. Blower speed control switch
9. Wire harness−
AC−64
AC−52
AC−57
AC−69 −
No air temperature control
1. Engine coolant volume
2. A/C control assembly
3. Water valve−
AC−69
AC−49
No compressor operation
1. Refrigerant volume
2. A.C Fuse
3. Magnetic clutch
4. Compressor
5. Pressure switch
6. Heater main relay
7. Blower speed control switch
8. A/C switch
9. A/C amplifier
10.Thermistor
11. Wire harnessAC−5 −
AC−33
AC−33
AC−61
AC−64
AC−69
AC−69
AC−74
AC−60 −
Compressor operates intermitently
1. Refrigerant volume
2. Pressure switch
3. A/C amplifier
4. Thermistor
5. Wire harnessAC−5
AC−61
AC−74
AC−60 −
No cool air comes out
1. Refrigerant volume
2. Refrigerant pressure
3. Drive belt
4. Magnetic clutch
5. Compressor
6. Pressure switch
7. Thermistor
8. A/C switch
9. A/C amplifier
10.A/C control assembly
11. Wire harnessAC−5
AC−5
AC−15
AC−33
AC−33
AC−61
AC−60
AC−69
AC−74
AC−69 −
Cool air comes out only at high engine rpm
1. Refrigerant volume
2. Drive bel
3. Magnetic clutch
4. Compressor
5. Condenser
6. Receiver
7. Expansion valve
8. Evaporator
9. Thermistor
10.A/C amplifier
11. Wire harnessAC−5
AC−15
AC−33
AC−33
AC−42
AC−39
AC−47
AC−45
AC−60
AC−74 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AC−4
−
AIR CONDITIONING AIR CONDITIONING SYSTEM
1996 LAND CRUISER (RM451U)
Insuf
ficient cooling
1. Refrigerant volume
2. Drive belt
3. Magnetic clutch
4. Compressor
5. Condenser
6. Receiver
7. Expansion valve
8. Evaporator
9. Refrigerant line
10.Pressure switch
11. A/C amplifier
12.A/C control assemblyAC−5
AC−15
AC−33
AC−33
AC−42
AC−39
AC−47
AC−45
AC−20
AC−61
AC−74
AC−69
No engine idle up when A/C switch ON
1. A/C amplifier
2. ECM
3. Wire harnessAC−74 −
−
No warm air comes out
1. Engine coolant volume
2. A/C control assembly
3. Water valve
4. Heater radiator−
AC−69
AC−49
AC−46
A/C indicator does not light up when mode lever at DEF. position
1. Defroster mode switch
2. A/C switch
3. Wire harnessAC−69
AC−69 −
Rear heater:
SymptomSuspect AreaSee page
No blower operation
1. RR HTR Fuse
2. Rear heater relay
3. Rear heater switch
4. Rear blower motor
5. Rear blower resistor−
AC−65
AC−77
AC−55
AC−58
No warm air come out1. Engine coolant volume
2. Rear heater radiator−
AC−46
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LT−01
BE−2
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
SymptomSuspect AreaSee page
Ignition switch is not set to each position.5. Ignition SwitchBE−11
”Key unlock warning system” does not operate.
1. GAUGE Fuse (I/P F/B)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire Harness−
BE−11
BE−21 −
HEADLIGHT AND TAILLIGHT SYSTEM
SymptomSuspect AreaSee page
Headlight does not light up. (Taillight is normal.)
1. Headlight Bulb
2. MAIN FL
3. HEAD (LH) Fuse (No.2 R/B)
4. HEAD (RH) Fuse (No.2 R/B)
5. Light Control Switch
6. Headlight Dimmer Switch
7. Wire Harness−
−
−
−
BE−14
BE−14
−
Headlight does not light up. (Taillight does not light up.)
1. Headlight Bulb
2. Light Control Switch
3. Headlight Dimmer Switch
4. Wire Harness−
BE−14
BE−14 −
Only one light comes ON.
1. Headlight Bulb
2. HEAD (LH) Fuse (No.2 R/B)
3. HEAD (RH) Fuse (No.2 R/B)
4. Wire Harness−
−
−
−
”Lo− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Hi− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Flash” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
Taillight does not light up. (Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (I/P F/B)
3. Light Control Switch
4. Taillight Control Relay (No.2 R/B)
5. Wire Harness−
−
BE−14
BE−14 −
Taillight does not light up. (Headlight does not light up.)
1. Taillight Bulb
2. MAIN FL
3. TAIL Fuse (I/P F/B)
4. Light Control Switch
5. Wire Harness−
−
−
BE−14 −
Headlight and Taillight does not light.1. Light Control Switch
2. Wire HarnessBE−14
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−3
1996 LAND CRUISER (RM451U)
Only one side taillight does not light.
1. Taillight Bulb
2. Wire Harness−
−
Taillight does not light.
(Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (No.2 R/B)
3. Taillight Control Relay (No.2 R/B)
4. Light Control Switch
5. Wire Harness−
BE−14
BE−14
BE−14 −
TURN SIGNAL AND HAZARD WARNING SYSTEM
SymptomSuspect AreaSee page
”Hazard” and ”Turn” do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher (No.1 R/B)
3. Wire HarnessBE−19
BE−19
−
None of blinks for hazard. (Turn is normal.)
1. Bulb
2. Turn Signal Flasher (No.1 R/B)
3. Wire Harness−
BE−19 −
Hazard warning light does not light up. (Turn is normal.)1. HAZ − HORN Fuse (No.2 R/B)
2. Wire HarnessBE−19 −
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE−19−
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Flasher (No.1 R/B)
3. Wire Harness−
BE−19 −
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE−19−
Only one bulb does not light up for hazard turn.1. Bulb
2. Wire Harness−
−
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. Ignition Switch
2. TURN Fuse (I/P F/B)
3. Turn Signal Switch
4. Wire HarnessBE−11
BE−19
BE−19 −
Turn signal does not light up.
(Combination meter, wiper and washer are normal.)1. TURN Fuse (I/P F/B)
2. Turn Signal Switch
3. Wire HarnessBE−19
BE−19−
INTERIOR LIGHT SYSTEM
SymptomSuspect AreaSee page
Room light does not light up.
1. DOME Fuse (No.2 R/B)
2. Door Courtesy Switch
3. Front Personal Light
4. Room Light Assembly
5. Bulb
6. Wire Harness−
BE−21
BE−21
BE−21 −
−
Room light remains always on.1. Door Courtesy Switch
2. Wire HarnessBE−21
−
BACK −UP LIGHT SYSTEM
SymptomSuspect AreaSee page
Back−Up light does not light up.
1. GAUGE Fuse (I/P F/B)
2. Ignition Switch
3. Park/Neutral Position Switch (A/T)
4. Bulb
5. Wire Harness−
BE−11 −
−
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−4
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Back−
Up light remains on.
1. Park/Neutral Position Switch (A/T)
2. Wire Harness−
−
Only one light does not light up.1. Bulb
2. Wire Harness−
−
STOP LIGHT SYSTEM
SymptomSuspect AreaSee page
Stop light does not light up.
1. STOP Fuse (I/P F/B)
2. Stop Light Switch
3. Bulb
4. Wire Harness−
BE−25 −
−
Stop light remains always on.1. Stop Light Switch
2. Wire HarnessBE−25−
Only one light does not light up.1. Wire Harness
2. Bulb−
−
WIPER AND WASHER SYSTEM
SymptomSuspect AreaSee page
Wipers do not operate or return to off position.
1. WIPER Fuse (I/P F/B)
2. Wiper Switch
3. Wiper Motor
4. Wiper Relay
5. Wire HarnessBE−27
BE−27
BE−27
BE−27
−
Wipers do not operate in MIST.
1. Wiper Switch
2. Wiper Motor
3. Wiper Relay
4. Wire HarnessBE−27
BE−27
BE−27
−
Wipers do not operate in INT.
1. Wiper Switch
2. Wiper Motor
3. Wiper Relay
4. Wire HarnessBE−27
BE−27
BE−27−
Washer does not operate.
1. Washer Hose or Nozzle Clogged
2. Washer Switch
3. Washer Motor
4. Wire Harness−
BE−27
BE−27 −
METER, GAUGES AND ILLUMINATION:
COMBINATION METER
SymptomSuspect AreaSee page
Tachometer, speedometer, engine coolant temperature gauge and
fuel gauge do not operate.1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Speedometer does not operate.
1. No.1 Vehicle Speed Sensor
2. Speedometer Driven Gear and Drive Gear
3. Meter Circuit
4. Wire HarnessBE−34−
BE−32 −
Tachometer does not operate.
1. Meter Circuit
2. Igniter
3. Wire HarnessBE−32−
−
Tachometer does not operate.
1. Meter Circuit
2. Igniter
3. Wire HarnessBE−32−
−
Voltmeter does not operate.1. Voltmeter Receiver Gauge
2. Wire HarnessAT −6
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−5
1996 LAND CRUISER (RM451U)
Fuel gauge does not operate or abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32
−
Engine coolant temperature gauge does not operation or
abnormal operate.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32−
Oil pressure gauge does not operate or abnormal operation.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−34−
All illumination lights do not light up.
1. TAIL Fuse (I/P F/B)
2. Light Control Rheostat
3. Wire Harness−
BE−34 −
Brightness does not change even when rheostat turned.1. Bulb
2. Wire Harness−
−
Only one illumination light does not light up.1. Bulb
2. Wire Harness−
−
WARNING LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
Warning lights do not lights up.
(Except discharge, SRS and door open)1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Brake warning light does not light up.
1. Bulb
2. Brake Fluid Level Switch
3. Parking Brake Switch
4. Meter Circuit
5. Wire Harness−
BE−34
BE−34
BE−32 −
Open door warning light does not light up.
1. Bulb
2. Door Courtesy Switch
3. DOME Fuse (No.2 R/B)
4. Meter Circuit
5. Wire Harness−
BE−21
BE−21 −
−
−
SRS warning light does not light up
1. Bulb
2. Airbag Sensor Assembly
3. ECU− B Fuse (I/P F/B)
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Discharge warning light does not light up.
1. Bulb
2. IGN Fuse (No.1 J/B)
3. Generator
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Seat belt warning light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Seat Belt Warning Relay (I/P F/B)
4. Meter Circuit
5. Wire Harness−
BE−34 −
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010