1996 TOYOTA LAND CRUISER Fuse a

S00816
BatteryFusible
Link
F8F7
11
W−R
3EA2
W−R11 6
IG Switch B−R
Fuse BlockIGN B−L
22
22 2
2
EFI Main Relay
1
2
3 4
EFI R
−Y
EC
EB
B−R
1EB1
R
Y−R
Y−REA2IH1
22 7
BR−B E4
E7 E7 E7
IGSW
MRLY
+B
E1 B+
ECM
1
3
12
24FL AM2
FL MAIN
W R
R/B No.2 Y
DI−11 0
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
ECM Power Source Circuit
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, battery positive voltage is applied t\
o the coil, closing the contacts of
the EFI main relay (Marking: EFI) and supplying power to the terminals +B\
of the ECM.
WIRING DIAGRAM
DI5PX−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24681
DI−11 2
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
4 Check IGN fuse from fuse block.
NG Check for short in all the harness and
components connected to IGN fuse.
OK
5 Check ignition switch.
PREPARATION:
(a) Remove instrument lower finish panel.
(b) Remove instrument cluster finish center panel No.2.
CHECK:
Check continuity between terminals.
OK:
Shift PositionTerminal No. to continuityTerminal No. to continuity
LOCK−−
ACC3 − 4−
ON2 − 3 − 46 − 11
START1 − 2 − 45 − 6 − 11
NG Replace ignition switch.
OK
Check for open and short in harness and
connector between battery and ignition
switch and ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00191
ONMRLY(+)
(−)
BE6653
P24682
−
DIAGNOSTICS ENGINE
DI−11 3
1996 LAND CRUISER (RM451U)
6 Check voltage between terminal MREL of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal MREL of ECM and body
ground.
OK:
Voltage: 9 − 14 V
NG Check and replace ECM.
OK
7 Check EFI fuse (Marking: EFI) (See page DI−105).
NG Check for short in all the harness and
components connected to EFI fuse.
OK
8 Check EFI main relay (Marking: EFI) (See page SF−54).
NG Replace EFI main relay (Marking: EFI).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

S02978
Battery
FL MAINFL AM2
F7E81
1
EA23
W−R W−R
W
2
22
2 2
2
EFI Main Relay
1 2 3 4
R−Y
Y−R
Y−R
EB1
IH1
22Y R
2
1 4
3
IG Switch 6
11
B−R B−LCircuit
Opening
Relay
Fuse Block R−G
R−W 5
Fuel Pump
Relay
123
1
2
Fuel Pump
Resister
R−B
R−B
ID2
BO1
13
3
36 Fuel Pump W−B
5
BO1
W−B
W−RR−W
IH1
17
E7
E7
E4 3
13
14
MRLYR
FC
FPR B+
E01
E01
ECM
BF
EA2
7
Fusible
LinkFEI
EB
R−G
R−W
R−G
1
BR
R/B No.2
IGN
DI−11 6
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P09401
−
DIAGNOSTICS ENGINE
DI−11 7
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand −held tester and check operation of fuel pump.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Use ACTIVE TEST mode to operate the fuel pump.
CHECK:
Check for fuel pressure in the fuel return hose when it is pinched
off.
OK:
There is pressure in the fuel return hose.
HINT:
At this time, you will hear a fuel flowing noise.
OK Go to step 4.
NG
2 Check circuit opening relay (See page SF−56 ).
NG Replace circuit opening relay.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00192
ONFC
(+)
(−)
BE6653
P24684
DI−11 8
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
3 Check voltage between terminal FC of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page
SF−65 ).
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal FC of ECM and body
ground.
OK:
Voltage: 9 − 14 V
OK Go to step 5.
NG
Check for open and short in harness and connector between terminal FC of ECM a\
nd circuit open-
ing relay and fuse block (See page IN−28).
4 Connect the TOYOTA hand−held tester and check operation of fuel pump relay.
PREPARATION:
(a) Connect the TOYOTA hand−held tester to the DLC3.
(b) Start the engine.
(c) Turn TOYOTA hand−held tester main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand−held tester.
CHECK:
Check operation of fuel pump relay when it is switched ON and OFF by the\
TOYOTA hand −held tester.
OK:
Operating noise can be heard from the relay.
OK Go to step 8.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−122
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
2 Check circuit opening relay (See page DI−84 ).
NG Replace circuit opening relay.
OK
3 Check voltage between terminal FC of ECM connector and body ground (See\
step 3 of TOYOTA hand −held tester).
OK Go to step 4.
NG
Check for open and short in harness and connector between terminal FC of ECM a\
nd circuit open-
ing relay and fuse block (See page IN−28).
4 Check operation of fuel pump relay (See step 5 of TOYOTA hand −held tester).
NG Replace fuel pump relay.
OK
5 Check voltage between terminal FPR of ECM connector and body ground (Se\
e step 6 of TOYOTA hand −held tester).
NG Check and replace ECM (See page IN−28 ).
6 Check for open and short in harness and connector between terminal FC of\
ECM
connector and fuel pump relay (See page IN−28).
NG Repair or replace harness or connector.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00197
ONON
OFF
BE6653
P22965
P22966
G
E
G E Air Filter
Air Filter
DI−126
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
TOYOTA hand −held tester
1 Connect the TOYOTA hand−held tester and check operation of VSV for fuel
pressure control.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and TOYOTA hand −held tester
main switch ON.
(d) Select the ACTIVE TEST mode on the TOYOTA hand −
held tester.
CHECK:
Check operation of VSV when VSV is operated by the T OYOTA
hand −held tester.
OK:
VSV is ON:
Air from pipe E is flowing out through the air filter.
VSV is OFF:
Air from pipe E is flowing out through pipe G.
OK Check and repair fuel pressure regulator (See page SF−19 ).
NG
2 Check VSV for fuel pressure control (See page SF−59).
NG Replace VSV for fuel pressure control.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010