1996 TOYOTA LAND CRUISER generator

IN0CI−02
IN−38
−
INTRODUCTION TERMS
1996 LAND CRUISER (RM451U)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE− J1930 terms and abbreviations used in this manual in compliance with SAE\
rec-
ommendations, as well as their TOYOTA equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOT A TERMS
( ) −−ABBREVIA TIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal−
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection−
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position−
CTOXContinuous T rap Oxidizer−
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition−
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode−
ECLEngine Control Level−
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant T emperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionTOYOTA Distributorless Ignition (TDI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control−
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory−
FEPROMFlash Erasable Programmable Read Only Memory−
FFFlexible Fuel−
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−5
1996 LAND CRUISER (RM451U)
Fuel gauge does not operate or abnormal operation.
1. Fuel Receiver Gauge
2. Fuel Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32
−
Engine coolant temperature gauge does not operation or
abnormal operate.
1. Engine Coolant Temperature Receiver Gauge
2. Engine Coolant Temperature Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−32−
Oil pressure gauge does not operate or abnormal operation.
1. Oil Pressure Receiver Gauge
2. Oil Pressure Sender Gauge
3. Meter Circuit
4. Wire HarnessBE−34
BE−34
BE−34−
All illumination lights do not light up.
1. TAIL Fuse (I/P F/B)
2. Light Control Rheostat
3. Wire Harness−
BE−34 −
Brightness does not change even when rheostat turned.1. Bulb
2. Wire Harness−
−
Only one illumination light does not light up.1. Bulb
2. Wire Harness−
−
WARNING LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
Warning lights do not lights up.
(Except discharge, SRS and door open)1. GAUGE Fuse (I/P F/B)
2. Meter Circuit
3. Wire Harness−
BE−32 −
Brake warning light does not light up.
1. Bulb
2. Brake Fluid Level Switch
3. Parking Brake Switch
4. Meter Circuit
5. Wire Harness−
BE−34
BE−34
BE−32 −
Open door warning light does not light up.
1. Bulb
2. Door Courtesy Switch
3. DOME Fuse (No.2 R/B)
4. Meter Circuit
5. Wire Harness−
BE−21
BE−21 −
−
−
SRS warning light does not light up
1. Bulb
2. Airbag Sensor Assembly
3. ECU− B Fuse (I/P F/B)
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Discharge warning light does not light up.
1. Bulb
2. IGN Fuse (No.1 J/B)
3. Generator
4. Meter Circuit
5. Wire Harness−
−
−
BE−32 −
Seat belt warning light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Seat Belt Warning Relay (I/P F/B)
4. Meter Circuit
5. Wire Harness−
BE−34 −
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P03788
CORRECT WRONG
Clearance
Z00038
Nippondenso Borroughs
−
CHARGING CHARGING SYSTEM
CH−3
1996 LAND CRUISER (RM451U)
(b) Check the fusible link and fuses for continuity.
Fusible link
MAIN 2.0 A
AM1 1.25 B
AM2 0.3 P
H−fuseAM1 50 A
FuseIGN 7.5 A
GAUGE 15 A
3. INSPECT DRIVE BELTS
(a) Visually check the drive belt for cracks, oiliness or wear.
Check that the belt does not touch the bottom of the pulley
groove.
If necessary, replace the drive belts as a set.
(b) Using a belt tension gauge, measure the belt tension. Belt tension gauge:
Nippondenso BTG−20 (95506 −00020)
Borroughts No. BT−33−73F
Drive belt tension:
New belt400 − 580 N (41.0 − 59.1 kgf, 90.4 − 130.2 lbf)
Used belt200 − 390 N (20.4 − 40.0 kgf, 45.0 − 88.2 lbf)
If the belt tension is not as specified, adjust it.
HINT:
”New belt” refers to a belt which has been used less than
5 minutes on a running engine.
”Used belt” refers to a belt which has been used on a run-
ning engine for 5 minutes or more.
After installing a new belt, run the engine for about 5 min-
utes and recheck the belt tension.
4. VISUALLY CHECK GENERATOR WIRING AND LIS- TEN FOR ABNORMAL NOISES
(a) Check that the wiring is in good condition.
(b) Check that there is no abnormal noise from the generator
while the engine is running.
5. INSPECT DISCHARGE WARNING LIGHT CIRCUIT
(a) Turn the ignition switch ”ON”. Check that the discharge warning light comes on.
(b) Start the engine. Check that the light goes off.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CH−4
−
CHARGING CHARGING SYSTEM
1996 LAND CRUISER (RM451U)
If the light does not operate as specified, troubleshoot the dis-
charge warning light circuit.
6. INSPECT CHARGING CIRCUIT WITHOUT LOAD
HINT:
If a battery/generator tester is available, connect the tester to
the charging circuit as per the manufacturer’s instructions.
(a) If a tester is not available, connect a voltmeter and amme-
ter to the charging circuit as follows:
Disconnect the wire from terminal B of the generator
and connect it to the negative ( −) lead of the amme-
ter.
Connect the positive (+) lead of the ammeter to ter-
minal B of the generator.
Connect the positive (+) lead of the voltmeter to ter-
minal B of the generator.
Ground the negative ( −) lead of the voltmeter.
(b) Check the charging circuit as follows:
With the engine running from idle to 2,000 rpm, check the
reading on the ammeter and voltmeter.
Standard amperage 10 A or less
Standard voltage:
at 25° C ’(77°F)14.0 − 15.0 V
at 115°C ’(239° F)13.5 − 14.3 V
If the voltmeter reading is more than standard voltage, replace
the voltage regulator.
If the voltmeter reading is less than the standard voltage, check
the voltage regulator and generator as follows:
With terminal F grounded, start the engine and
check the voltmeter reading of terminal B.
If the voltmeter reading is more than standard volt-
age, replace the voltage regulator.
If the voltmeter reading is less than standard volt-
age, check the generator.
7. INSPECT CHARGING CIRCUIT WITH LOAD
(a) With the engine running at 2,000 rpm, turn on the high
beam headlights and place the heater blower switch at
”HI”.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
CHARGING CHARGING SYSTEM
CH−5
1996 LAND CRUISER (RM451U)
(b) Check the reading on the ammeter.
Standard amperage: 30 A or more
If the ammeter reading is less than standard amperage, repair
the generator.
HINT:
If the battery is fully charged, the indication will sometimes be
less than standard amperage.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CH06H−05
CH−6
−
CHARGING GENERATOR
771
Author: Date:
1996 LAND CRUISER (RM451U)
GENERATOR
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
CHARGING GENERATOR
CH−7
772
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CH0EP−01
CH−8
−
CHARGING GENERATOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE BATTERY AND BATTERY TRAY
2. DISCONNECT POWER STEERING (PS) RESERVOIR TANK
3. REMOVE DRIVE BELTS
(a) Loosen the lock bolt, pivot bolt and adjusting bolt.
(b) Remove the 2 drive belts.
4. REMOVE GENERATOR
(a) Disconnect the generator connector.
(b) Remove the rubber cap and nut, and disconnect the gen-
erator wire.
(c) Disconnect the generator wire clamp from the generator.
(d) Remove the lock bolt, bolt, nut and drive belt adjusting bar.
(e) Remove the pivot bolt and generator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010