1996 TOYOTA LAND CRUISER headlight

BE1LS−01
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−1
1139
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL SYSTEM
PRECAUTION
Take care to observe the following precautions when performing inspections o\
r removal and replacement
of body electrical related parts.
1. HEADLIGHT SYSTEM
Halogen bulbs have pressurized gas inside and require special handling. They ca\
n burst if scratched or
dropped. Hold a bulb only by its plastic or metal case. Don’t touch the glass\
part of a bulb with bare hands.
2. SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
The LAND CRUISER is equipped with an SRS (Supplemental Restraint System) such as the driver airbag
and front passenger airbag. Failure to carry out service operation in th\
e correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing (in\
-
cluding removal or installation of parts, inspection or replacement), be sure t\
o read the precautionary notices
in the RS section.
3. AUDIO SYSTEM
If the negative (−) terminal cable is disconnected from the battery, the preset AM, FM 1 and FM 2 stations
stored in memory are erased, so be sure to note the stations and reset them af\
ter the negative ( −) terminal
cable is reconnected to the battery.
4. MOBILE COMMUNICATION SYSTEM
If the vehicle is equipped with a mobile communication system, refer to \
precautions in the IN section.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LT−01
BE−2
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
SymptomSuspect AreaSee page
Ignition switch is not set to each position.5. Ignition SwitchBE−11
”Key unlock warning system” does not operate.
1. GAUGE Fuse (I/P F/B)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire Harness−
BE−11
BE−21 −
HEADLIGHT AND TAILLIGHT SYSTEM
SymptomSuspect AreaSee page
Headlight does not light up. (Taillight is normal.)
1. Headlight Bulb
2. MAIN FL
3. HEAD (LH) Fuse (No.2 R/B)
4. HEAD (RH) Fuse (No.2 R/B)
5. Light Control Switch
6. Headlight Dimmer Switch
7. Wire Harness−
−
−
−
BE−14
BE−14
−
Headlight does not light up. (Taillight does not light up.)
1. Headlight Bulb
2. Light Control Switch
3. Headlight Dimmer Switch
4. Wire Harness−
BE−14
BE−14 −
Only one light comes ON.
1. Headlight Bulb
2. HEAD (LH) Fuse (No.2 R/B)
3. HEAD (RH) Fuse (No.2 R/B)
4. Wire Harness−
−
−
−
”Lo− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Hi− Beam” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
”Flash” does not light up.
1. Headlight Bulb
2. Headlight Control Relay (No.2 R/B)
3. Headlight Dimmer Switch
4. Wire Harness−
−
BE−14 −
Taillight does not light up. (Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (I/P F/B)
3. Light Control Switch
4. Taillight Control Relay (No.2 R/B)
5. Wire Harness−
−
BE−14
BE−14 −
Taillight does not light up. (Headlight does not light up.)
1. Taillight Bulb
2. MAIN FL
3. TAIL Fuse (I/P F/B)
4. Light Control Switch
5. Wire Harness−
−
−
BE−14 −
Headlight and Taillight does not light.1. Light Control Switch
2. Wire HarnessBE−14
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
BE−3
1996 LAND CRUISER (RM451U)
Only one side taillight does not light.
1. Taillight Bulb
2. Wire Harness−
−
Taillight does not light.
(Headlight is normal.)
1. Taillight Bulb
2. TAIL Fuse (No.2 R/B)
3. Taillight Control Relay (No.2 R/B)
4. Light Control Switch
5. Wire Harness−
BE−14
BE−14
BE−14 −
TURN SIGNAL AND HAZARD WARNING SYSTEM
SymptomSuspect AreaSee page
”Hazard” and ”Turn” do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher (No.1 R/B)
3. Wire HarnessBE−19
BE−19
−
None of blinks for hazard. (Turn is normal.)
1. Bulb
2. Turn Signal Flasher (No.1 R/B)
3. Wire Harness−
BE−19 −
Hazard warning light does not light up. (Turn is normal.)1. HAZ − HORN Fuse (No.2 R/B)
2. Wire HarnessBE−19 −
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE−19−
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Flasher (No.1 R/B)
3. Wire Harness−
BE−19 −
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE−19−
Only one bulb does not light up for hazard turn.1. Bulb
2. Wire Harness−
−
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. Ignition Switch
2. TURN Fuse (I/P F/B)
3. Turn Signal Switch
4. Wire HarnessBE−11
BE−19
BE−19 −
Turn signal does not light up.
(Combination meter, wiper and washer are normal.)1. TURN Fuse (I/P F/B)
2. Turn Signal Switch
3. Wire HarnessBE−19
BE−19−
INTERIOR LIGHT SYSTEM
SymptomSuspect AreaSee page
Room light does not light up.
1. DOME Fuse (No.2 R/B)
2. Door Courtesy Switch
3. Front Personal Light
4. Room Light Assembly
5. Bulb
6. Wire Harness−
BE−21
BE−21
BE−21 −
−
Room light remains always on.1. Door Courtesy Switch
2. Wire HarnessBE−21
−
BACK −UP LIGHT SYSTEM
SymptomSuspect AreaSee page
Back−Up light does not light up.
1. GAUGE Fuse (I/P F/B)
2. Ignition Switch
3. Park/Neutral Position Switch (A/T)
4. Bulb
5. Wire Harness−
BE−11 −
−
−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−6
−
BODY ELECTRICAL BODY ELECTRICAL SYSTEM
1996 LAND CRUISER (RM451U)
Engine oil level warning light does not light up.
1. Bulb
2. Meter Circuit
3. Engine Oil Level Warning Switch
4. Wire Harness−
BE−32
BE−34 −
Low oil pressure warning light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−32
BE−34 −
Fuel level warning light does not light up.
1. Bulb
2. Fuel Level Warning Switch
3. Meter Circuit
4. Wire Harness−
BE−34
BE−32 −
INDICATOR LIGHTS:
COMBINATION METER
SymptomSuspect AreaSee page
High beam indicator light does not light up.
1. Bulb
2. Headlight and Taillight System
3. Meter Circuit
4. Wire Harness−
BE−19
BE−32 −
Shift indicator lights do not light up. (ALL)
1. Shift Position Indicator Wiring Circuit
2. Park/Neutral Position Switch
3. Wire Harness
4. Bulb−
BE−34 AT −6
−
Shift indicator lights do not light up. (L, 2, D)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Park/Neutral Position Switch
4. Light Control Rheostat
5. Wire Harness−
BE−34 AT −6
BE−34 −
Shift indicator lights do not light up. (PWR)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. Pattern Select Switch
4. Wire Harness−
BE−34 AT −6
−
Shift indicator lights do not light up. (2nd START)
1. Bulb
2. Shift Position Indicator Wiring Circuit
3. ECM
4. Wire Harness−
AT −6
−
−
Only one shift indicator does not light up.1. Bulb
2. Shift Position Indicator Wiring Circuit−
BE−34
Indicator lights do not light up. (Except Turn, Hi −beam)1. GAUGE Fuse (I/P F/B)
2. Wire Harness−
−
O/D OFF indicator light does not light up.
1. Bulb
2. O/D Main Switch
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Malfunction indicator light does not light up.
1. Bulb
2. ECM
3. Wire Harness−
−
−
Cruise control indicator light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit
4. Wire Harness−
−
BE−32 −
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LX−01
BE−12
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
1150
Author: Date:
1996 LAND CRUISER (RM451U)
HEADLIGHT AND TAILLIGHT SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LY−01
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
BE−13
1996 LAND CRUISER (RM451U)
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LZ−01
BE−14
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT LIGHT CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
TAILA2 − A11Continuity
HEADA2 − A11 − A13Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
FlashA9 − A12 − A14Continuity
Low beamA3 − A9Continuity
High beamA9 − A12Continuity
If continuity is not as specified, replace the switch.
3. INSPECT HEADLIGHT CONTROL RELAY CONTINU-
ITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.3 − 4Continuity
If continuity is not as specified, replace the relay.
4. INSPECT TAILLIGHT CONTROL RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.2 − 3Continuity
If continuity is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
BE−15
1996 LAND CRUISER (RM451U)
5. INSPECT HEADLIGHT RETAINER CIRCUIT
(a) Connect the positive (+) leads from the battery to termi-
nals 1 and 6, and the negative ( −) lead to terminal 3.
(b) Connect the 3.4 W test bulb between terminal 7 and the positive (+) lead from the battery.
(c) Disconnect the positive (+) lead from terminal 1, and check that the test bulb is lighting.
(d) Connect the negative ( −) lead to terminal 5, and check
that the test bulb goes out.
If operation is not as specified, replace the relay.
6. INSPECT TAILLIGHT CIRCUIT
(a) Connect the positive (+) leads from the battery to termi- nals 1 and 6, and the negative ( −) lead to terminal 2.
(b) Connect the 3.4 W test bulb between terminal 8 and the positive (+) lead from the battery.
(c) Disconnect the positive (+) lead from terminal 1, and check that the test bulb is lighting.
(d) Connect the negative ( −) lead to terminal 5, and check
that the test bulb goes out.
If operation is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010