1995 TOYOTA SUPRA engine

(See page EG±404)
Check voltage between terminal +B and E1 of engine control module con-
nector.
(1) Connect SST (check harness ªAº).
(See page Eg±404)
SST 09990±01000
(2) Turn ignition switch ON.
Measure voltage between terminal +B and E1 of
engine control module connector.
Voltage: 9 Ð 14 V
Check and replace engine control module.
Repair or replace harness or connector.
Check voltage between terminal IGSV Check and replace engine control module
connector and body ground.
Proceed to next circuit inspection shown on
matrix chart (See page
EG±408).
Check for open in harness and connector between terminal E1 of engine control
module and body ground (See page
IN±30).
Turn ignition switch ON.
Measure voltage between terminal IGSW of en-
gine control module connector and body ground.
Voltage: 9 Ð 14 V

INSPECTION PROCEDURE
EG±466± ENGINE2JZ±GE ENGINE TROUBLESHOOTING

Check IGN fuse.
Remove IGN fuse from J/B No.1.
Check continuity of IGN fuse.
Continuity
Check for short in the harness and all the com-
ponents connected to IGN fuse (See Electrical
Wiring Diagram).
Check ignition switch.
(1) Remove finish lower panel and finish lower
panel LH.
(2) Remove heater to register duct No.2.
Check continuity between terminals.
Replace ignition switch.
Check and repair harness and connector between
battery and ignition switch, ignition switch and en-
gine control module.
± ENGINE2JZ±GE ENGINE TROUBLESHOOTINGEG±467

Check voltage between terminal M±REL of engine control module connector
and body ground.
Turn ignition switch ON.
Measure voltage between terminal M±REL of en-
gine control module connector and body ground.
Voltage: 9 Ð 14 V
Check and replace engine control module.
Check EFI No.1 Fuse.
Remove EFI No.1 fuse from R/B No.2.
Check continuity of EFI No.1 fuse.
Continuity
Check for short in the harness and all the compo-
nents connected to EFI No.1 fuse (See Electrical
Wiring Diagram).
EG±468± ENGINE2JZ±GE ENGINE TROUBLESHOOTING

Check EFI main relay.
Remove EFI main relay from R/B No.2.
Check continuity between terminals of EFI main
relay shown below.
Replace EFI main relay.
(1) Apply battery voltage between terminals 1
and 2.
(2) Check continuity between terminals 3 and 5.
Repair or replace harness or connector.
Check and repair harness or connector between
EFI No.1 fuse and battery.
Check for open and short in harness and connector between terminal M±REL
of engine control module and body ground(See page
IN±30).
Terminals 3 and 5
Terminals 3 and 5
Terminals 1 and 2
Open
Continuity
Continuity
(Reference value 72
)
± ENGINE2JZ±GE ENGINE TROUBLESHOOTINGEG±469

Back Up Power Source Circuit
CIRCUIT DESCRIPTION
Battery positive voltage is supplied to terminal BATT of the ECM even when the ignition switch is off for use by
the diagnostic trouble code memory and air±fuel ratio adaptive control value memory, etc.
EG±470± ENGINE2JZ±GE ENGINE TROUBLESHOOTING

INSPECTION PROCEDURE
Check EFI No.1 Fuse.
Remove EFI No.1 fuse from R/B No.2.
Check continuity of EFI No.1 fuse.
Continuity
Check for short in the harness and all the com-
ponents connected to EFI No.1 fuse (See Electri-
cal Wiring Diagram).
Connect SST (check harness ªAº).
(See page EG±404)
SST 09990±01000
Measure voltage between terminal BATT of en-
gine control module connector and body ground.
Voltage: 9 Ð 14 V
Check and replace engine control module.
Check and repair harness or connector between
engine control module and EFI No.1 fuse, EFI No.1
fuse and battery.
Proceed to next circuit inspection shown on matrix
chart (See page
EG±408).
Check voltage between terminal BATT of engine control module connector
and body ground.
Are the diagnostic trouble codes still in the memory when the ignition switch
is turned OFF?
± ENGINE2JZ±GE ENGINE TROUBLESHOOTINGEG±471

Injector Circuit
CIRCUIT DESCRIPTION
The injectors are located in the intake manifold. They inject fuel into the cylinders based on the signals
from the engine control module.
INSPECTION USING OSCILLOSCOPE

With the engine idling measure waveform between terminals #10 ~ 60 and E01 of engine
control module.
HINT: The correct waveform is as shown.
EG±472± ENGINE2JZ±GE ENGINE TROUBLESHOOTING

INSPECTION PROCEDURE
(See page EG±404)
Check voltage between terminals # 10 ~ 60 of engine control module and
body ground.
(1) Connect SST check harness ªAº).
(See page EG±404)
SST 09990±01000
(2) Turn ignition switch ON.
Measure voltage between terminals #10
~ 60 of
engine control module and body ground.
Voltage: 9 Ð 14 V
Check for short in the harness and all the compo-
nents connected to AM2 fuse.
Remove AM2 fuse from R/B No.2.
Check continuity of AM2 fuse.
Continuity
Check and repair harness or connector between en-
gine control module and battery.
Check AM2 Fuse.
± ENGINE2JZ±GE ENGINE TROUBLESHOOTINGEG±473