13. INSTALL PS PUMP
(a) Install the pump bracket with the 2 bolts.
Torque:
A 58 NVm (590 kgfVcm, 43 ftVlbf)
B 39 NVm (400 kgfVcm, 29 ftVlbf)
(b) Install the pump rear stay with the 2 bolts.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(c) Install the pump housing to the pump bracket.
(d) Connect the following hoses:
wAir hose to No.4 timing belt cover
wAir hose to air intake chamber
(e) Install the front pump bracket with the 2 bolts (A).
Torque: 58 NVm (590 kgfVcm, 43 ftVlbf)
(f) Install the plate washer and bolt (B) to the oil pump.
Torque: 52 NVm (530 kgfVcm, 38 ftVlbf)
14. INSTALL ENGINE WIRE BRACKET
15. CONNECT FUEL HOSES
(a) Connect the fuel return hose to the fuel return pipe.
(b) Install the fuel return hose to the clamp of the oil dipstick
guide.
(c) Install the fuel inlet hose with 2 new gaskets and the union
bolt.
Torque: 29 NVm (300 kgfVcm, 22 ftVlbf)
16. CONNECT WIRES AND CONNECTORS
17. CONNECT EVAP HOSE
18. CONNECT BRAKE BOOSTER VACUUM HOSE
19. CONNECT HEATER HOSES
20. INSTALL CHARCOAL CANISTER
21. INSTALL WATER PUMP PULLEY, FAN, FLUID COUPLING
ASSEMBLY AND DRIVE BELT
(See step 10 in water pump installation in Cooling Sys-
tem)
22. INSTALL AIR CLEANER, VAF METER AND INTAKE AIR
CONNECTOR PIPE ASSEMBLY
23. CONNECT CONTROL CABLES TO THROTTLE BODY
24. FILL WITH FUEL
25. FILL WITH ENGINE OIL
26. CHECK IGNITION TIMING
(See ignition timing inspection and adjustment)
27. INSTALL RADIATOR ASSEMBLY
(See radiator installation in Cooling System)
28. START ENGINE AND CHECK FOR LEAKS
29. INSTALL HOOD
30. ROAD TEST VEHICLE
Check for abnormal noise, shock slippage, correct shift
points and smooth operation.
31. RECHECK ENGINE COOLANT AND ENGINE OIL LEVELS EG±128
± ENGINEENGINE MECHANICAL
6. INSTALL 10 VANE PLATES
Install the plate with the round end facing outward.
7. INSTALL GASKET
Install a new gasket to the front housing.
8. INSTALL SIDE REAR PLATE
Align the holes of the plate and straight pins.
NOTICE: Make sure you install the plate facing the cor-
rect direction.
9. INSTALL WAVE WASHER
Install the washer so that its protrusions fit into the slots in the
side rear plate.
10. INSTALL REAR HOUSING
(a) Coat 2 new O±rings with power steering fluid.
(b) Install the 2 O±ring to the housing.
(c) Torque the 2 bolts.
Torque: 17 NVm (170 kgfVcm, 12 ftVlbf)
11. I N S TA L L S P R I N G , F L O W C O N T R O L VA LV E A N D
PRESSURE PORT UNION
(a) Coat a new O±ring with power steering fluid and install it to
the union.
(b) Torque the union.
Torque: 83 NVm (850 kgfVcm, 61 ftVlbf)
12. 2JZ±GTE:
INSTALL SUCTION PORT UNION
(a) Install a new O±ring to the union.
(b) Torque the bolt.
Torque: 13 NVm (130 kgfVcm, 9 ftVlbf)
13. 2JZ±GE:
INSTALL OIL RESERVOIR
(a) Coat a new O±ring with power steering fluid and install it to
the reservoir.
(b) Torque the 3 bolts.
Torque:
Front side bolt: 13 NVm (130 kgfVcm, 9 ftVlbf)
Rear side bolts: 17 NVm (170 kgfVcm, 12 ftVlbf)
14. MEASURE PS VANE PUMP ROTATING TORQUE
(See page SR±27)
± STEERINGPOWER STEERING VANE PUMPSR±31
