1995 TOYOTA SUPRA engine

LIGHT FAILURE SENSOR INSPECTION
1. INSPECT SENSOR CIRCUIT
Disconnect the connector from the sensor and inspect the
connector on the wire harness side, as shown.
 
 
 
Tester connection to
terminal number
 
 
 
Condition
 
 
 
Specified condition
 1±Ground Constant Continuity*
 2±Ground Constant Continuity*
 9±Ground Constant Continuity* 
 10±Ground
 
 Constant
 
 Continuity*
 11±Ground Constant Continuity
 12±Ground Constant Continuity*
 3±Ground Light control switch position OFF No Voltage 3±Ground Light control switch position TAIL or HEAD Battery positive voltage 
 4±Ground
 
 Ignition switch position LOCK or ACC
 
 No voltage
 4±Ground Ignition switch position ON Battery positive voltage
 7±Ground Stop light switch position OFF No voltage
 7±Ground Stop light switch position ON Battery positive voltage 
 8±Ground
 
 Engine condition Stop
 
 No voltage
 8±Ground Engine condition Running Battery positive voltage
*: There is resistance because this circuit is grounded
through the bulb.
If circuit is as specified, replace the sensor.
If the circuit is not as specified, inspect the circuits connected
to other parts.
2. INSPECT WARNING LIGHT
(a) Disconnect the connector from the light failure sensor and
ground terminal 4 on the wire harness side connector.
(b) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or inspect
wire harness.
± BODY ELECTRICAL SYSTEMCOMBINATION METERBE±53

 Problem No.
 Noise Noise produced by vibration or shock while driving. 30
  Noise produced when engine starts. 31
 Antenna Antenna±related. 32
 ANTI±THEFT SYSTEM Troubleshooting for ANTI±THEFT SYSTEM 33
HOW TO USE DIAGNOSTIC CHART
Is tape player operating
Is ACC applied to radio?Tape player faulty.
Check if GND (wire harness side)
to radio is OK.
Radio faulty.Radio assembly faulty.
Check if CIG & RAD fuse is OK.Replace fuse.
Is ACC applied to radio?
Is ACC applied to tape player?
Is ACC applied to power amplifier?
ACC wire harness faulty?
NO POWER COMING INRadio
(1) Audio system type and symbol used.
HINT: Confirm the applicable type of audio system.
(2) Symbol for type of audio system the question applies to.
HINT: If the audio system type is not applicable, proceed to next question below.
(3) Junction without black circle.
HINT: Proceed to next question below.
(4) Junction with black circle.
HINT: Proceed to question for applicable audio system type.
(5) HINT: Select question for applicable audio system type.
± BODY ELECTRICAL SYSTEMAUDIO SYSTEMBE±87

A/C noise.Whining noise occurs when A/C is operating.
Fuel gauge noise.
NoiseNOISE PRODUCED WHEN ENGINE STARTS
Whistling noise which becomes high±pitched
when accelerator strongly depressed, disap-
pears shortly after engine stops.
Clicking sound heard when horn button is
pressed, then released. Whirring/grating sound
when pushed continuously.
Scratching noise occurs during sudden accelera-
tion, driving on rough roads or when ignition
switch is turned on.
Alternator noise.
Horn noise.
Ignition noise.
Turn signal noise.
Washer noise.
Murmuring sound, stops when engine stops.
Tick±tock noise, occurs in co±ordination with
blinking of flasher.
Noise occurs during window washer operation.
Scraping noise in time with wiper beat.
Scratching noise occurs while engine is running,
continues a while even after engine stops.
Other type of noise.
Engine coolant temp. gauge noise.
Wiper noise.
± BODY ELECTRICAL SYSTEMAUDIO SYSTEMBE±109

SYSTEM INSPECTION
1. SETTING OF THE THEFT DETERRENT SYSTEM
Setting Conditions
(a) Close all the doors.
(b) Close the engine hood and luggage compartment door.
(c) Remove the ignition key from the ignition key cylinder.
Setting Operation
When any of the following operations (a) or (c) is done, the theft deterrent indicator light will light up as de-
scribed.
(a) Lock the left or right front door using the key.
(All doors are locked by key±interlinked lock operation)
(b) With the rear doors locked and with one of the front doors locked, lock the other front door without
using the key (keyless door lock).
 
 Elapsed time after operation
 
 Indicator light
  Within about 30 seconds  Lights up
  After about 30 seconds  Blinks *1
*1: 1 sec. on, 1 sec. off
HINT: When the theft deterrent system is set, doors cannot be locked or unlocked with the door lock control
switch and the luggage compartment door cannot be unlocked with the luggage compartment door opener
switch.
2. CANCELLING OF THE THEFT DETERRENT SYSTEM IN THE SET CONDITION
Check if the theft deterrent indicator light is blinking.
Cancelling Operation
When any of the following operation (a), (b), (c) or (d) is done, the theft deterrent system is cancelled and
indicator light will go off.
(a) Unlock the left or right front door using the key.
(b) Insert the ignition key in the ignition key cylinder and turn it to the ACC or ON position.
(This is operative only when the theft deterrent system has never operated.)
(c) Unlock the luggage compartment door with the key. *
1
*1: The theft deterrent system is temporarily cancelled only while the luggage compartment door is
open. Approximately 2 seconds after the luggage compartment door is closed, the theft deterrent
system is reset.
± BODY ELECTRICAL SYSTEMTHEFT DETERRENT AND DOOR LOCK CONTROL SYSTEMBE±121

3. CHECK OF THE THEFT DETERRENT SYSTEM OPERATION.
Check if the theft deterrent indicator light is blinking.
When any of the following operations (a) or (b) is done, the system sounds the horns and theft deterrent
horn and flashes the headlights and taillights for about one minute to alert. At the same time, the system
disconnects the starter motor circuit and locks all doors (if all doors are not locked, the system repeats door
locking operation every 2 seconds during the one minute alert time).
(a) Open the engine hood using the engine hood opener lever.
(b) Unlock any of the front or rear doors without key operation.
4. CANCELLING OF THE THEFT DETERRENT SYSTEM IN OPERATING CONDITION.
The theft deterrent operation can be cancelled when any of the following conditions is met:
 No. Condition Cancelling Operation 
 1
 
 Unlock left or right door with the key.
 
 
 2 Unlock doors with wireless door lock control system. 
 3 Insert key into ignition key cylinder and turn it to ACC or ON position. *2
 4 About 1 minute passes after theft deterrent operation begins. Automatic stop *1
*1: In this case, the theft deterrent system resets in about 2 seconds after if all doors are closed.
*
2: The alarm will be off, but the engine will not operate. To restart the engine, see No.1.
ECU TERMINAL VALUES MEASUREMENT
USING TOYOTA BREAK±OUT±BOX AND
TOYOTA HAND±HELD TESTER
1. Hook up the TOYOTA break±out box and TOYOTA handheld
tester to the vehicle.
2. Read the ECU input/output values by following the prompts
on the hand±held tester screen.
HINT: TOYOTA hand±held tester has a ºShapshotº func-
tion. This records the measured values and is effective in
the diagnosis of intermittent problems.
Please refer to the TOYOTA hand±held tester/TOYOTA
break±out±box operator's manual for further details. BE±122
± BODY ELECTRICAL SYSTEMTHEFT DETERRENT AND DOOR LOCK CONTROL SYSTEM

MATRIX CHART OF PROBLEM SYMPTOMS
Proceed to the reference page shown in the matrix chart below for each malfunction symptom and troubleshoot
for each circuit.
HINT: Troubleshooting of the theft deterrent system is based on the premise that the door lock control system
is operating normally. Accordingly, before troubleshooting the theft deterrent system, first make certain that the
door lock control system is operating normally.
Theft Deterrent System
 Details of Problem Inspecting Circuit *1 See Page
  1. Indicator light circuit BE±128
 
 
Th th ft d t t t t b t
 
 2. Luggage compartment door key
lock and unlock switch circuit 
 BE±142
 The theft deterrent system cannot be set 3. Luggage Room Light switch circuit BE±144 
 
 
 4. Door courtesy switch circuit
 
 BE±147
  5. Engine hood courtesy switch circuit BE±148
 The indicator light does not blink when system is set Indicator light circuit BE±128
 
 
 When the
system is
 
 
 
When the back door is
opened by a method other
than the key. 
 
 The system
does not
 
 
 
Luggage compartment door courtesy
switch circuit
 
 
 BE±144
 
 
system is
set 
 When the engine hood is
opened 
 
does not
Operate 
 Engine hood courtesy switch circuit
 
 BE±148
 
 
 
 Horns do not sound 
 Horn relay circuit 
 BE±132
 
 While the system
ii i
 
 
Theft deterrent horn does not
sound 
 
Theft deterrent horn circuit 
 
BE±134
 is in warning
operation Headlights do not flash Headlight control relay circuit BE±136
 o eration Taillights do not flash Taillight control relay circuit BE±138
  The starter cut is not cut off Starter relay circuit BE±130 
 
 When the
System is
 
 
 
It is not cancelled when the
ignition key is Turned to ACC
or ON position
 
 
 Ignition switch circuit
 
 
 BE±140
 
 
 
System is
Set 
 
 
It still operates when the back
door is Opened with the key
 
 
 
Luggage compartment door key lock
and unlock switch circuit
 
 
 
BE±142
 System is still set even when a rear door is open Door courtesy switch circuit BE±147
  Horns sound Horn relay circuit BE±132
 Even when the Theft deterrent horn sounds Theft deterrent horn circuit BE±134
 

Even when the
System is not set 
Headlights stay on 
Headlight control relay circuit 
BE±136 
 
 
 Taillights stay on
 
 Taillight control relay circuit
 
 BE±138
*1
: If numbers are given to the circuit proceed with troubleshooting in the order indicated by those numbers.
± BODY ELECTRICAL SYSTEMBE±123THEFT DETERRENT AND DOOR LOCK CONTROL SYSTEM

TERMINALS OF ECU
 No. Symbol Terminal Name No. Symbol Terminal Name
 T8±1 +B2 Power Source T9±1 +B1 Power Source
 T8±2 ACT± Door Lock Motor T9±2 ± ± 
 T8±3
 
 ACT+
 
 Door Lock Motor
 
 T9±3
 
 ±
 
 ±
 T8±4 E Ground 
T9 4
 
DSWL
 Luggage Compartment Door Courtesy
 T8±5 ± ± T9±4 DSWL 
Luggage Com artment Door Courtesy
Switch
 T8±6 RLY Power Main Relay T9±5 L1 Door Lock Control Switch (Lock) 
 T8±7
 
 IG
 
 Ignition Switch ºONº
 
 T9±6
 
 UL3
 
 Door Key Lock and Unlock Switch
 T8±8 ACC Ignition Switch ºACCº T9±7 DSWD Door Open Detection Switch
 T8±9 ± ± T9±8 UL1 Door Lock Control Switch (Unlock)
 
T9 9
 
LUG
 Luggage Compartment Door Key Lock T9±9 LUG Luggage Com artment Door Key Lock
and Unlock Switch
 T9±10 HEAD Headlight Control Relay 
 T9±11
 
 SH
 
 Theft Deterrent Horn
 T9±12 IND Security Indicator Light
 T9±13 ± ±
 T9±14 FOD Engine Hood Courtesy Switch  
LSWD
 
Door Unlock Detection Switch or Door T9±15 LSWD,
UL2 Door Unlock Detection Switch or Door
K L k d U l k S it h
T9±15
UL2Key Lock and Unlock Switch 
 T9±16
 
 ±
 
 ±
 T9±17 ± ±
 T9±18 ± ±
 T9±19 DSWP Door Open Detection Switch 
 T9±20
 
 KSW
 
 Key Unlock Warning Switch
 T9±21 LSWP Door Unlock Detection Switch
 T9±22 L2 Door Key Lock and Unlock Switch
 T9±23 TAIL Taillight Control Relay 
 T9±24
 
 HORN
 
 HORN Relay
 T9±25 SRLY Ignition Switch ºSTº
± BODY ELECTRICAL SYSTEMBE±125THEFT DETERRENT AND DOOR LOCK CONTROL SYSTEM

 Terminals Symbols Condition Standard Value
 
 
T9±12±Ground
(IND±Ground) 
 W±L±Ground
 
 Always
 
 Below 270

 T9±14±T8±4 
VR WB
 Engine hood courtesy switch ON (hood opened). Below 1
 
 
T9 14 T8 4
(FOD±E) 
 
VR±WB 
 Engine hood courtesy switch OFF (hood closed). 
 1 M
or higher
 T9±15±T8±4 LW W B Door unlock detection switch ON (door opened). Below 1

 
T9 15 T8 4
(LSWD±E) LW±WB Door unlock detection switch OFF (door closed). 1 M
or higher
 
T9 15 T8 4
  Door key lock and unlock switch ºunlockº position Below 1
 
 
T9±15±T8±4
(UL2±E) 
 W±WB 
 Door key lock and unlock switch OFF or ºlockº
position 
 1 M
or higher
   
Door open detection switch (passenger's) ON
 
Below 1
 
 T9±19±T8±4
 
 RL WB
 
 
Door oen detection switch ( assenger s) ON
(door opened). 
 
Below 1

 
T9 19 T8 4
(DSWP±E) 
RL±WB
 Door open detection switch (passenger's) OFF 1M
or higher
   
Door oen detection switch ( assenger s) OFF
(door closed). 
1 M
or higher
 T9±20±T8±4 
YWB
 Key unlock warning switch ON. Below 1

 
T9 20 T8 4
(KSW±E) Y±WB Key unlock warning switch OFF. 1 M
or higher
 
T9±21±T8±4
 
GB WB
 Door unlock detection switch ON (door opened). Below 1
 
 
T9 21 T8 4
(LSWP±E) 
 
GB±WB 
 Door unlock detection switch OFF (door closed).
 
 1 M
or higher
 
T9 22 T8 4
  Door key lock and unlock switch ºlockº position. Below 1

 
 
T9±22±T8±4
(L2±E) 
 
GY±WB 
 
Door key lock and unlock switch OFF or ºunlockº
position. 
 1 M
or higher
 
 T9±23±T8±4
(TAIL±E) 
 GW±WB
 
 Light control switch ºTAILº position.
 
 10±14 V
 
 T9±24±T8±4
(HORN±E) 
 LR±WB
 
 Horn switch OFF.
 
 10±14 V
 
 T9±25±Ground
(SRLY±Ground) 
 L±O±Ground
 
 Ignition switch is turned to ºSTº position.
(When park / neutral position switch ºPº position) 
 10±14 V
± BODY ELECTRICAL SYSTEMBE±127THEFT DETERRENT AND DOOR LOCK CONTROL SYSTEM