Page 1407 of 2248
4CHECK ENGINE COOLANT TEMPERATURE
SENSOR.
< REF. TO“F: DTC P0115 [T11F0].”>
1) Turn ignition switch to OFF.
OBD0145A
2) Connect the Subaru Select Monitor or the OBD-II gen-
eral scan tool to data link connector.
3) Start the engine and warm-up completely.
OBD0176
OBD0177
4) Read data on Subaru Select Monitor or the OBD-II gen-
eral scan tool.
Subaru Select Monitor
Designate mode using function key.
Function mode: F05 or F06
F05: Water temperature is indicated in“°F”.
F06: Water temperature is indicated in“°C”.
: Is temperature indicated on Subaru Select
Monitor (F05) greater than 140°F?
Is temperature indicated on Subaru Select
Monitor (F06) greater than 60°C?
: Go to step 5.
: Replace engine coolant temperature sensor.
OBD-II general scan tool
For detailed operation procedures, refer to the OBD-II Gen-
eral Scan Tool Instruction Manual.
201
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostics Chart with Trouble Code
Page 1485 of 2248
OBD0380
AO: DTC P0710
—TRANSMISSION FLUID TEMPERATURE
SENSOR CIRCUIT MALFUNCTION (ATF)—
H2M1145
DESCRIPTION:
This sensor is mounted to the control valve in the transmis-
sion. It detects temperature change as an analog electrical
signal. The output characteristics of the sensor are shown
in the illustration.
DTC DETECTING CONDITION:
Two consecutive trips with fault
TROUBLE SYMPTOM:
No shift up to 4th speed (after engine warm-up)
No lock-up occurs. (after engine warm-up)
Excessive shift shock
279
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostics Chart with Trouble Code
Page 1486 of 2248
1.Check harness connector between TCM and
ATF temperature sensor.
2.Check ATF temperature sensor.
3.Check input signal for TCM.
CAUTION:
After repair or replacement of faulty parts, conduct
CLEAR MEMORY and INSPECTION MODES.
[T3D0] and [T3E0].>
WIRING DIAGRAM:
OBD0383
NOTE:
For the diagnostic procedure on transmission fluid tem-
perature sensor circuit, refer to“3-2 [T7G0]”.
280
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostics Chart with Trouble Code
Page 1496 of 2248
1.Check any other DTC (besides DTC P0740) on
display.
2.Check duty solenoid B circuit.
[T7B0]”.>
3.Check throttle position sensor circuit.
“3-2 [T7L0]”.>
4.Check vehicle speed sensor 1 circuit.
“3-2 [T7M0]”.>
5.Check vehicle speed sensor 2 circuit.
“3-2 [T7N0]”.>
6.Check engine speed input circuit.
[T7I0]”.>
7.Check inhibitor switch circuit.
DTC P0705 [T11AN0]”.>
8.Check brake light switch circuit.
DTC P0703 [T11AM0]”.>
9.Check ATF temperature sensor circuit.
“3-2 [T7G0]”.>
CAUTION:
After repair or replacement of faulty parts, conduct
CLEAR MEMORY and INSPECTION MODES.
[T3D0] and [T3E0].>
290
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostics Chart with Trouble Code
Page 1499 of 2248
7
CHECK INHIBITOR SWITCH CIRCUIT.
: Is there any trouble in inhibitor switch cir-
cuit?
: Repair or replace inhibitor switch circuit.
: Go to step 8.
8
CHECK BRAKE LIGHT SWITCH CIRCUIT.
: Is there any trouble in brake light switch cir-
cuit?
: Repair or replace brake light switch circuit.
: Go to step 9.
9CHECK ATF TEMPERATURE SENSOR CIR-
CUIT.
: Is there any trouble in ATF temperature sen-
sor circuit?
: Repair or replace ATF temperature sensor circuit.
: Go to next.
: Is there poor contact in TCM connector?
: Repair poor contact in TCM connector.
: Go to next.
: Is there any mechanical trouble in automatic
transmission?
: Repair or replace automatic transmission.
: Replace TCM with a new one.
293
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostics Chart with Trouble Code
Page 1537 of 2248
OBD0527
BI: DTC P1500
—RADIATOR FAN RELAY 1 CIRCUIT
MALFUNCTION (FAN
—1)—
DESCRIPTION:
The engine cooling system consists of a down-flow
radiator which features high heat-dissipation performance,
an electric motor fan, an engine coolant pump, a
thermostat, and an engine coolant temperature sensor.
The ON-OFF control of the radiator fan is governed by
the ECM which receives signals sent from the engine cool-
ant temperature sensor. On models which are equipped
with an air conditioning system, the ECM receives signals
sent from the engine coolant temperature sensor, vehicle
speed sensor 2 and A/C switch. These signals simulta-
neously turn ON or OFF the radiator main fan and radiator
sub fan as well as setting them at“HI”or“LO”speed.
[Without A/C models]
Engine coolant temperature signal *1ECM output signal Operation of radiator fan
Radiator fan relay 1 Main
ON ON ON
OFF OFF OFF
*1 ON: Above 95°C (203°F), OFF: Below 89°C (192°F)
[With A/C models]
Engine coolant
temperature
signal *2A/C compressorVehicle speed
signal *3ECM output signal Operation of radiator fan
Radiator fan
relay 1Radiator fan
relay 2Main Sub
ONONON ON ON HI HI
OFF ON ON HI HI
OFFON ON ON HI HI
OFF ON OFF LO LO
OFFONON ON ON HI HI
OFF ON OFF LO LO
OFFON OFF OFF OFF OFF
OFF OFF OFF OFF OFF
*2 ON: Above 95°C (203°F), OFF: Below 89°C (192°F)
*3 ON: Above 20 km/h (12 MPH), OFF: Below 10 km/h (6 MPH)
331
2-7ON-BOARD DIAGNOSTICS II SYSTEM
11. Diagnostics Chart with Trouble Code
Page 1557 of 2248
G3M0717
3. OPERATION OF SHIFT SELECTOR LEVER
WARNING:
Stop the engine while checking operation of selector
lever.
1) Check that selector lever does not move from“N”to“R”
without pushing the button.
2) Check that selector lever does not move from“R”to“P”
without pushing the button.
3) Check that selector lever does not move from“P”to“R”
without pushing the button.
4) Check that selector lever does not move from“3”to“2”
without pushing the button.
3. Electrical Components Location
1. SENSOR AND CONTROL MODULE
B3M0178B
1Throttle position sensor
2Dropping resistor
3Vehicle speed sensor 2
4Inhibitor switch
5ECM
6Vehicle speed sensor 1 (AWD)
7Vehicle speed sensor 1 (FWD)
8TCM
9Data link connector (for Subaru select monitor only)
10Data link connector (for Subaru select monitor and OBD-II
general scan tool)
11Diagnosis connector
12Diagnosis terminal
13AT OIL TEMP indicator light
(AT diagnostic indicator light)
3
3-2AUTOMATIC TRANSMISSION AND DIFFERENTIAL
2. Pre-inspection - 3. Electrical Components Location
Page 1558 of 2248
G3M0717
3. OPERATION OF SHIFT SELECTOR LEVER
WARNING:
Stop the engine while checking operation of selector
lever.
1) Check that selector lever does not move from“N”to“R”
without pushing the button.
2) Check that selector lever does not move from“R”to“P”
without pushing the button.
3) Check that selector lever does not move from“P”to“R”
without pushing the button.
4) Check that selector lever does not move from“3”to“2”
without pushing the button.
3. Electrical Components Location
1. SENSOR AND CONTROL MODULE
B3M0178B
1Throttle position sensor
2Dropping resistor
3Vehicle speed sensor 2
4Inhibitor switch
5ECM
6Vehicle speed sensor 1 (AWD)
7Vehicle speed sensor 1 (FWD)
8TCM
9Data link connector (for Subaru select monitor only)
10Data link connector (for Subaru select monitor and OBD-II
general scan tool)
11Diagnosis connector
12Diagnosis terminal
13AT OIL TEMP indicator light
(AT diagnostic indicator light)
3
3-2AUTOMATIC TRANSMISSION AND DIFFERENTIAL
2. Pre-inspection - 3. Electrical Components Location
![SUBARU LEGACY 1995 Service Repair Manual 4CHECK ENGINE COOLANT TEMPERATURE
SENSOR.
< REF. TO“F: DTC P0115 [T11F0].”>
1) Turn ignition switch to OFF.
OBD0145A
2) Connect the Subaru Select Monitor or the OBD-II gen-
eral scan tool to data](/manual-img/17/57432/w960_57432-1406.png "SUBARU LEGACY 1995 Service Repair Manual 4CHECK ENGINE COOLANT TEMPERATURE
SENSOR.
< REF. TO“F: DTC P0115 [T11F0].”>
1) Turn ignition switch to OFF.
OBD0145A
2) Connect the Subaru Select Monitor or the OBD-II gen-
eral scan tool to data")
![SUBARU LEGACY 1995 Service Repair Manual 1.Check any other DTC (besides DTC P0740) on
display.
2.Check duty solenoid B circuit. <Ref. to“3-2
[T7B0]”.>
3.Check throttle position sensor circuit. <Ref. to
“3-2 [T7L0]”.>
4.Check vehicle](/manual-img/17/57432/w960_57432-1495.png "SUBARU LEGACY 1995 Service Repair Manual 1.Check any other DTC (besides DTC P0740) on
display.
2.Check duty solenoid B circuit. <Ref. to“3-2
[T7B0]”.>
3.Check throttle position sensor circuit. <Ref. to
“3-2 [T7L0]”.>
4.Check vehicle")
