1994 JEEP CHEROKEE Flat towing

PORTABLE STARTING UNIT
There are many types of portable starting units
available for starting engines. Follow the manufac-
turer's instructions when involved in any engine
starting procedure.
HOISTING RECOMMENDATIONS
FLOOR JACK
When properly positioned, a floor jack can be used
to lift a Jeeptvehicle. Support the vehicle in the
raised position with jack stands at the front and rear
ends as applicable (Fig. 7).
CAUTION: Do not attempt to lift a JeepTvehicle
with a floor jack positioned under:
²an axle tube,
²a body side sill,
²a steering linkage component,
²a drive shaft,
²the engine or transmission oil pan,
²the fuel tank, or
²a front suspension arm.
Use the correct sub-frame rail or frame rail
lifting locations only (Fig. 7).
HOIST
A Jeeptvehicle can be lifted with a swiveling-arm
type hoist; with a wheel-lift, twin-post hoist; or with
a ramp-type, drive-on hoist.
When a swiveling-arm, frame-contact type
hoist is used, ensure that the lifting pads are po-
sitioned at the correct sub frame rail (Fig. 7).
TOWING RECOMMENDATIONS
TOWING EQUIPMENT
A vehicle equipped with SAE approved sling-type
towing equipment can be used to tow all Jeeptvehi-
cles (Fig. 8). When it is necessary to rear-tow a vehi-
cle, use the wheel-lift towing method with a tow
dolly located under the front wheels. A vehicle with
flat-bed towing equipment can also be used to trans-
port a disabled vehicle.
A wooden crossbeam with spacer blocks could pos-
sibly be required for proper connection when using
the sling-type, front-end towing method (Fig. 9).
SAFETY PRECAUTIONS
The following safety precautions must be consid-
ered when preparing for and during a vehicle towing
operation:
Fig. 7 Correct Vehicle Lifting LocationsÐTypical
Fig. 8 Tow Vehicles With Approved Equipment
Fig. 9 Crossbeam & Spacer Block Construction
0 - 8 LUBRICATION AND MAINTENANCEJ

²if the vehicle is damaged, secure the loose and pro-
truding parts;
²always use a safety chain system that is indepen-
dent of the lifting and towing equipment;
²do not allow any of the towing equipment to con-
tact the disabled vehicle's fuel tank;
²do not allow anyone to be under the disabled vehi-
cle while it is lifted by the towing equipment;
²do not allow passengers to ride in a vehicle being
towed;
²always observe all state and local laws involving
warning signals, night illumination, speed, etc.
²do not attempt a towing operation that could jeop-
ardize the safety of the operator, bystanders or other
motorists;
²do not exceed a towing speed of 48 km/h (30 mph);
²avoid towing distances of more than 24 km (15
miles) whenever possible; and
²do not attach tow chains or a tow sling to a
bumper, the steering linkage, the universal joints,
the constant velocity (CV) joints, or a drive shaft.
CLEARANCES AND RAMP ANGLE
SURFACE CLEARANCE
The end of the disabled vehicle that is attached to
the tow vehicle should be lifted a minimum of 10 cm
or four inches off the surface. Inspect to ensure that
the opposite end of the disabled vehicle has clearance
from the surface.
RAMP ANGLEÐFLAT-BED TOWING
If a vehicle with flat-bed towing equipment is used,
the approach ramp angle should not exceed 15 de-
grees.
SLING-TYPE, FRONT-END TOWING
XJ VEHICLES
Use the following guidelines when the tow vehicle
is attached to the front end of a disabled vehicle.
(1) Always tow with the front wheels lifted off the
surface and turned all the way to the right.
(2) Attach a J-hook to the disabled vehicle at the
left side of the axle (Fig. 10).
(3) Position the sling crossbar close to the J-hook
and below the front bumper (Fig. 11).
(4) Secure a chain to the right side of vehicle by
placing it over the axle shaft tube and attaching it to
a structural member.
(5) Attach the safety chains to the vehicle.
2WD With Manual Or Automatic Transmission
(6) Turn the ignition switch to the OFF position to
unlock the steering wheel.
(7) Shift the transmission to NEUTRAL, mark the
drive shaft and axle drive pinion gear shaft yoke for
installation reference. Remove the drive shaft from
the vehicle.(8) Cover the exposed end of the transmission ex-
tension housing and the universal joints. Store the
drive shaft in a safe place.
4WD, Command-Trac (231 Part-Time 4WD
Transfer Case) And Manual Transmission
(6) Turn the ignition switch to the OFF position to
unlock the steering wheel.
When the transfer case is in the NEUTRAL po-
sition, both axles are disengaged from the pow-
ertrain. This allows the vehicle to be towed
without removing the drive shafts.
(7) Shift the manual transmission into a forward
gear and the transfer case to NEUTRAL.
4WD, Command-Trac (231 Part-Time 4WD
Transfer Case) And Automatic Transmission
(6) Turn the ignition switch to the OFF position to
unlock the steering wheel.
Fig. 10 Sling-Type, Front-End Towing (XJ Front
View)
Fig. 11 Sling-Type, Front-End Towing (XJ Rear
View)
JLUBRICATION AND MAINTENANCE 0 - 9

When the transfer case is in the NEUTRAL po-
sition, both axles are disengaged from the pow-
ertrain. This allows the vehicle to be towed
without removing the drive shafts.
(2) Shift the transfer case to NEUTRAL.
(3) The vehicle can now be towed with the front
wheels raised (refer to Sling-Type, Front-End Tow-
ing).
VEHICLE DOORS LOCKED
Place a tow dolly under the rear wheels (Fig. 14)
and tow with the front end raised (refer to Sling-
Type, Front-End Towing).
4WD EMERGENCY TOWINGÐTRANSFER CASE
NOT SHIFTED TO NEUTRAL
When a situation arises and the transfer case can-
not be shifted to NEUTRAL, any of the following
methods can be used to tow a 4WD vehicle.
Drive shafts not removed, place the rear
wheels on a tow dolly and tow with the front
end raised.
Drive shafts not removed, place the front
wheels on a tow dolly and tow with the rear end
raised.
Rear drive shaft removed, tow with the front
end raised.
Front drive shaft removed, tow with the rear
end raised.
Both drive shafts removed, tow with all four
wheels on the road surface.
(1) Turn ignition key switch to the unlocked (OFF)
position.
(2) Shift the transmission to the NEUTRAL posi-
tion.
(3) Determine the method by which the vehicle
will be towed and prepare the vehicle for towing.
(4) Connect the vehicle to the tow vehicle. Refer to
the applicable procedure.
FLAT TOWING (4 TIRES/WHEELS ON
SURFACE)
Tow a vehicle in this manner only when all four
wheels will freely rotate. Prepare the vehicle accord-
ing to the following procedures.
2WD VEHICLES
(1) Mark the drive shaft and the axle drive pinion
gear shaft yoke for installation alignment reference.
(2) Remove the drive shaft. Install a protective
covering over the drive shaft U-joints to retain them
assembled and protected.
(3) Cover the open end of the transmission exten-
sion housing.4WD VEHICLES
(1) Mark the drive shafts and the axle drive pinion
gear shaft yokes for installation alignment reference.
(2) Remove the drive shafts. Install a protective
covering over the drive shaft U-joints/CV-joints to re-
tain them assembled and protected.
(3) Cover the exposed ends of the transfer case.
CAUTION: Whenever a drive shaft has been re-
moved and installed, check the transmission fluid
level of the transmission and transfer case. Driving
a vehicle with low tranfer case fluid can damage the
transmission and transfer case.
EMERGENCY TOW HOOKS
WARNING: REMAIN AT A SAFE DISTANCE FROM A
VEHICLE THAT IS BEING TOWED VIA ITS TOW
HOOKS. THE TOW STRAPS/CHAINS COULD POSSI-
BLY BREAK AND CAUSE SERIOUS INJURY.
Some Jeeptvehicles are equipped with emergency
tow hooks located at the front end (Fig. 15). Some
Jeeptvehicles also have emergency tow hooks lo-
cated at the rear ende. The tow hooks should be used
forEMERGENCYpurposes only.
CAUTION: DO NOT use emergency tow hooks for
tow truck hook-up or highway towing.
Fig. 15 Emergency Front Tow HooksÐXJ & YJ
Vehicles
0 - 12 LUBRICATION AND MAINTENANCEJ

INSTRUMENT PANEL ILLUMINATION
LAMPS............................8E-16
INSTRUMENT PANEL LAMPS..............8E-4
INSTRUMENT PANEL REPLACEMENT.......8E-8
INSTRUMENT PANEL SERVICE..........23-192
INSULATION PANEL, DASH PANEL........23-95
INSULATOR PANEL, DASH PANEL.........23-11
INSULATOR PANEL, HOOD..............23-138
INTAKE AIR TEMPERATURE SENSOR......14-54
INTAKE AIR TEMPERATURE SENSORÐ
PCM INPUT.........................14-20
INTAKE AIR TEMPERATURE SENSOR TEST . . . 14-43
INTAKE DUCT, FRESH AIR...............24-41
INTAKE MANIFOLD.....................14-57
INTAKE MANIFOLDÐ2.5L ENGINE..........11-8
INTAKE MANIFOLDÐ4.0L ENGINE..........11-9
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR.......................8D-5,8D-27
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR TEST.......................8D-14
INTAKE MANIFOLD LEAKAGE DIAGNOSIS.....9-5
INTERCHANGEABILITY, PARTS............21-66
INTERIOR COMPONENTS..........23-91,23-190
INTERIOR LAMPS......................8L-19
INTERIOR LAMPS, XJ..................8L-23
INTERIOR LAMPS, YJ..................8L-23
INTERIOR PAINT CODES, XJ............23-205
INTERIOR PAINT CODES, YJ............23-206
INTERIOR REARVIEW MIRROR...........23-74
INTERIOR REARVIEW MIRROR
SUPPORT BRACKET REPLACEMENT......23-75
INTERIOR TRIM PANELS AND SCUFF
PLATESÐXJ VEHICLES...............23-112
INTERLOCK CABLE ADJUSTMENT (XJ),
PARK........................21-97,21-186
INTERMEDIATE (COUPLING) SHAFT . . 19-21,19-43
INTERMITTENT WINDSHIELD WASHER,
DIAGNOSING........................8K-12
INTERMITTENT WIPER MODULE...........8K-5
INTERMITTENT WIPER WASHER..........8K-20
INTERNATIONAL VEHICLE CONTROL
AND DISPLAY SYMBOLS............INTRO.-3
IN-VEHICLE SERVICE, 30RH/32RH.........21-96
IN-VEHICLE SERVICE, AW-4.............21-173
ISOLATION, COMPRESSOR..............24-17
JACK STORAGEÐXJ VEHICLES..........23-127
JOINT ANGLE MEASUREMENT,
UNIVERSAL..........................16-4
JOINT REPLACEMENT, UNIVERSAL.........16-9
JOINTS, UNIVERSAL....................16-2
JOUNCE BUMPER, REAR................13-18
JUMP STARTING........................0-7
JUMP STARTING, HOISTING AND TOWING.....0-7
KEY LOCK CYLINDER, DOOR.............23-54
KEY LOCK CYLINDER, FULL-METAL
DOOR............................23-178
KEY LOCK CYLINDERS.............23-2,23-132
KEY WARNING SWITCH REPLACEMENT,
IGNITION............................8U-4
KEYLESS ENTRY.......................8P-8
KNOCK, LOW SPEED; FRONT
SUSPENSION AND AXLE................2-17
KNOCK, LOW SPEED; REAR SUSPENSION
AND AXLES...........................3-8
KNUCKLE AND BALL STUDS, STEERING.....2-30
LABEL, TIRE INFLATION PRESSURE.....INTRO.-3
LABEL, VEHICLE EMISSION CONTROL
INFORMATION (VECI)
..................25-1
LABEL, VEHICLE SAFETY CERTIFICATION
. INTRO.-1
LABELS/DECALS/PLATES
...........23-1,23-132
LABELS/PLATES, CODES AND
DIMENSIONS, DESIGNATIONS,
.......INTRO.-1
LAG TEST, TIME
......................21-169
LAMP, 4WD INDICATOR
..................8E-2
LAMP, ANTI-LOCK BRAKE SYSTEM (ABS)
INDICATOR
..........................8E-2
LAMP BEAM ADJUSTMENT, FOG
..........8L-12
LAMP, BRAKE INDICATOR; INSTRUMENT
PANEL AND GAUGESÐXJ
...............8E-2
LAMP, BRAKE INDICATOR; INSTRUMENT
PANEL AND GAUGESÐYJ
..............8E-16
LAMP BULB REPLACEMENT, BACK-UP/
REAR TURN SIGNAL/TAIL
...............8L-9
LAMP BULB REPLACEMENT, FRONT PARK/
TURN SIGNAL
........................8L-8LAMP BULB REPLACEMENT, SIDE
MARKER............................8L-7
LAMP BULB REPLACEMENT,
UNDERHOOD........................8L-18
LAMP BULB REPLACEMENTÐYJ
VEHICLES, HARDTOP DOME/CARGO.....8L-20
LAMP BULB/ELEMENT REPLACEMENT,
FOG ...............................8L-13
LAMP (CHECK ENGINE), MALFUNCTION
INDICATOR; INSTRUMENT PANEL
AND GAUGESÐXJ................8E-2,8E-4
LAMP (CHECK ENGINE), MALFUNCTION
INDICATOR; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-16
LAMP (CHMSL)ÐXJ, CENTER HIGH
MOUNTED STOP.....................8L-10
LAMP (CHMSL)ÐYJ, CENTER HIGH
MOUNTED STOP.....................8L-11
LAMP, COOLANT TEMPERATURE
INDICATOR..........................8E-1
LAMP FOR DIAGNOSTIC TROUBLE CODES,
INDICATOR (CHECK ENGINE)...........8A-19
LAMP HOUSING, LIFTGATE LICENSE
PLATE .............................23-72
LAMP, I/P ASH RECEIVER TRAY..........23-92
LAMP, LICENSE PLATE..................8L-10
LAMP, LOW FUEL WARNING..............8E-2
LAMPÐPCM OUTPUT, EMR..............14-24
LAMPÐPCM OUTPUT, GENERATOR.......14-25
LAMPÐPCM OUTPUT, MALFUNCTION
INDICATOR.........................14-26
LAMP REPLACEMENT, DOME.............8L-20
LAMP REPLACEMENT, FOG..............8L-15
LAMP REPLACEMENT, UNDERHOOD.......8L-18
LAMP, SEAT BELT REMINDER............8E-16
LAMP SERVICE INFORMATION, DOME/
COURTESY.........................8L-19
LAMP SERVICE INFORMATION, FOG.......8L-12
LAMP SERVICE INFORMATION,
UNDERHOOD........................8L-17
LAMP, SERVICE REMINDER INDICATOR
(SRI)...............................25-1
LAMP SPEED CONTROL SWITCH TEST,
STOP...............................8H-7
LAMP SUPPORT BRACKET, I/P TWEETER
SPEAKER/COURTESY.................23-95
LAMP SWITCH REPLACEMENT, FOG.......8L-14
LAMP TROUBLE DIAGNOSIS, DOME/
COURTESY.........................8L-19
LAMP TROUBLE DIAGNOSIS, FOG.........8L-12
LAMP, UPSHIFT INDICATOR;
INSTRUMENT PANELAND GAUGESÐXJ....8E-2
LAMP, UPSHIFT INDICATOR;
INSTRUMENT PANELAND GAUGESÐYJ . . . 8E-16
LAMPÐYJ RENEGADE VEHICLES, FOG....23-150
LAMP/REAR WIPER SWITCHES, REAR
DEFOGGER/FOG......................8E-21
LAMPS, EXTERIOR......................8L-1
LAMPS, INDICATOR....................8E-14
LAMPS INOPERATIVE, DIAGNOSISÐ
HAZARD.........................8J-1,8J-2
LAMPS, INSTRUMENT PANEL.............8E-4
LAMPS, INSTRUMENT PANEL
ILLUMINATION......................8E-16
LAMPS, INTERIOR.....................8L-19
LAMPS OUT, DIAGNOSINGÐALL..........8E-16
LAMPS, XJ EXTERIOR..................8L-23
LAMPSÐXJ, HAZARD...................8J-1
LAMPS, XJ INTERIOR..................8L-23
LAMPS, YJ EXTERIOR..................8L-23
LAMPSÐYJ, HAZARD...................8J-2
LAMPS, YJ INTERIOR..................8L-23
LATCH ADJUSTMENT, DOOR.............23-55
LATCH AND RELEASE HANDLE,
TAILGATE..........................23-160
LATCH ASSEMBLY REPLACEMENT,
SOLENOID...........................8P-6
LATCH, DOOR.........................23-56
LATCH EXTERNAL RELEASE HANDLE,
FULL-METAL DOOR..................23-178
LATCH, FULL-METAL DOOR
.............23-179
LATCH, HOOD SAFETY
.................23-139
LATCH INSIDE RELEASE AND LOCK
HANDLE, FULL-METAL DOOR
..........23-175
LATCH RELEASE AND LOCK RODS,
DOOR INSIDE
.......................23-57LATCH RELEASE CABLE REPLACEMENT....23-10
LATCH REPLACEMENT, HOOD............23-10
LATCH STRIKER AND BUMPERÐXJ
VEHICLES, REAR SEATBACK...........23-111
LATCH STRIKER, HALF-METAL DOOR.....23-175
LATCH STRIKER REPLACEMENT, HOOD....23-10
LATCH STRIKER REPLACEMENT, SAFETY . . . 23-10
LATCH STRIKER, TAILGATE.............23-161
LATCH/KEY LOCK CYLINDER/STRIKER,
LIFTGATE...........................23-68
LEAD CORRECTION CHART...............22-5
LEAF SPRING; FRONT SUSPENSION AND
AXLE...............................2-14
LEAF SPRING; REAR SUSPENSION AND
AXLES............................3-3,3-6
LEAF SPRING EYE BUSHING
REPLACEMENT; FRONT SUSPENSION
AND AXLE...........................2-15
LEAF SPRING EYE BUSHING
REPLACEMENT; REAR SUSPENSION
AND AXLES........................3-4,3-6
LEAK DETECTION AND REPAIR, FIXED
GLASS WATER................23-83,23-189
LEAK DIAGNOSIS, CONVERTER HOUSING . . . 21-73
LEAK DOWN TEST, FUEL PRESSURE........14-7
LEAK TEST, REFRIGERANT................24-8
LEAKAGE DIAGNOSIS, GEAR
..............19-8
LEAKAGE DIAGNOSIS, INTAKE
MANIFOLD
............................9-5
LEAKAGE DIAGNOSIS, PUMP
..............19-8
LEAKAGE TEST, CYLINDER COMBUSTION
PRESSURE
...........................9-6
LEAKAGE TEST DIAGNOSIS, CYLINDER
COMBUSTION PRESSURE
................9-6
LEAKS, REPAIRING
.....................22-3
LEAKS, TESTING COOLING SYSTEM FOR
....7-18
LEFT HAND DRIVE, DRIVERS DOOR
POWER LOCK SWITCHÐ2-DOOR
.........8P-2
LEFT HAND DRIVE, DRIVERS DOOR
POWER WINDOW SWITCHÐ2-DOOR
......8S-6
LETTERS, JEEP BODY CODE
...............5-2
LEVEL AND CONDITION, CHECKING
FLUID
.......................21-96,21-173
LEVEL AND CONDITION, FLUID
...........21-69
LEVEL, BRAKE FLUID
....................5-13
LEVELÐBRAKELINES AND HOSES,
BRAKE BLEEDINGÐBRAKE FLUID
........5-13
LEVEL, CLUTCH FLUID
...................6-14
LEVEL, COMPRESSOR OIL
................24-6
LEVEL, CORRECT FLUID
.................5-48
LEVEL, TRANSFER CASE FILL
...........21-294
LEVELS, OPERATING SOUND
...............5-3
LEVER INSTALLATION (XJ WITH FULL
CONSOLE), PARKING BRAKE
............5-60
LEVER INSTALLATION (XJ WITH MINI
CONSOLE), PARKING BRAKE
............5-58
LEVER INSTALLATION (XJ WITHOUT
CONSOLE), PARKING BRAKE
............5-60
LEVER POSITIONS, TRANSMISSION
RANGES AND SHIFT
.................21-157
LEVER REMOVAL (XJ WITH FULL
CONSOLE), PARKING BRAKE
............5-59
LEVER REMOVAL (XJ WITH MINI
CONSOLE), PARKING BRAKE
............5-58
LEVER REMOVAL (XJ WITHOUT
CONSOLE), PARKING BRAKE
............5-60
LICENSE PLATE LAMP
..................8L-10
LICENSE PLATE LAMP HOUSING,
LIFTGATE
...........................23-72
LICENSE PLATE SCREW ANCHOR
AND BUMPER, LIFTGATE
..............23-72
LIFTGATE ADJUSTMENT
.................23-70
LIFTGATE GLASS, HARD TOP
............23-162
LIFTGATE GLASS WEATHERSTRIP SEAL
REPLACEMENT
.....................23-163
LIFTGATE HINGE
.......................23-67
LIFTGATE LATCH/KEY LOCK CYLINDER/
STRIKER
...........................23-68
LIFTGATE LICENSE PLATE LAMP
HOUSING
...........................23-72
LIFTGATE LICENSE PLATE SCREW
ANCHOR AND BUMPER
...............23-72
JINDEX13
Description Group-Page Description Group-Page Description Group-Page

TEMPERATURE SENSOR TEST, ENGINE
COOLANT; FUEL SYSTEM..............14-43
TEMPERATURE SENSOR TEST, ENGINE
COOLANT; IGNITION SYSTEMS..........8D-12
TEMPERATURE SENSOR TEST, INTAKE
AIR ...............................14-43
TEMPERATURE SENSOR TEST, INTAKE
MANIFOLD AIR......................8D-14
TENSION, BELT.......................8B-10
TENSION, DRIVE BELT...............7-33,7-38
TENSIONÐRIGHT HAND DRIVE
(RHD),BELT..........................7-34
TENSION SPECIFICATIONS, BELT...........7-34
TENSIONER REPLACEMENT (XJ), PARKING
BRAKE CABLE........................5-61
TENSIONERÐXJ MODELS, AUTOMATIC
BELT ...............................7-36
TERMINAL ASSEMBLY REPLACEMENT,
CONNECTOR.........................8W-5
TERMINAL REPLACEMENT...............8W-5
TEST, A/C PERFORMANCE................24-8
TEST, ACTUATOR MOTOR STALL...........8P-6
TEST, AIR PRESSURE...................21-73
TEST, ANALYZING THE ROAD.............21-70
TEST, BATTERY LOAD...................8A-4
TEST, BATTERY OPEN CIRCUIT VOLTAGE....8A-3
TEST, CAMSHAFT POSITION SENSOR;
FUEL SYSTEM.......................14-43
TEST, CAMSHAFT POSITION SENSOR;
IGNITION SYSTEMS...................8D-8
TEST, CONVERTER STALL...............21-72
TEST, CRANKSHAFT POSITION SENSOR;
FUEL SYSTEM.......................14-44
TEST, CRANKSHAFT POSITION SENSOR;
IGNITION SYSTEMS...................8D-9
TEST, CYLINDER COMBUSTION
PRESSURE LEAKAGE...................9-6
TEST, CYLINDER COMBUSTION
PRESSURE LEAKAGE DIAGNOSIS..........9-6
TEST, CYLINDER COMPRESSION PRESSURE . . 9-5
TEST, ENGINE COOLANT TEMPERATURE
SENSOR......................8D-12,14-43
TEST, EXTENDED IDLE SWITCH...........14-45
TEST, FUEL PRESSURE LEAK DOWN........14-7
TEST, FUEL PUMP CAPACITY..............14-7
TEST, FUEL SYSTEM PRESSURE......14-5,14-48
TEST, HYDRAULIC PRESSURE......21-71,21-168
TEST, HYDROMETER....................8A-3
TEST, IDLE AIR CONTROL MOTOR........14-46
TEST, INJECTOR.......................14-48
TEST, INTAKE AIR TEMPERATURE SENSOR . . 8D-14,
14-43
TEST, MANIFOLD ABSOLUTE PRESSURE
(MAP) SENSOR.................8D-14,14-44
TEST, MANUAL SHIFTING...............21-168
TEST, MASTER CYLINDER/POWER
BOOSTER............................5-11
TEST, OXYGEN SENSOR (O2S)
HEATING ELEMENT...................14-45
TEST, POWER BOOSTER CHECK VALVE......5-11
TEST, POWER BOOSTER VACUUM..........5-12
TEST PROCEDURES, BATTERY............8A-2
TEST PROCEDURES ON VEHICLE,
ENGINE STARTER MOTOR..............8A-9
TEST PROCEDURES ON VEHICLE,
GENERATOR........................8A-14
TEST, PUMP PRESSURE.................19-3
TEST, REAR WINDOW DEFOGGER GRID.....8N-1
TEST, REFRIGERANT LEAK................24-8
TEST, ROAD; TRANSMISSION AND
TRANSFER CASE.....................21-70
TEST, ROAD; VEHICLE SPEED CONTROL
SYSTEM............................8H-5
TEST SPECIFICATIONS, 30RH/32RH
PRESSURE........................21-323
TEST, SPEED CONTROL SWITCH (TURN
SIGNAL LEVER)......................8H-7
TEST, STARTER MOTOR RELAY...........14-48
TEST, STARTING SYSTEM COLD
CRANKING...........................8A-9
TEST, STOP LAMP SPEED CONTROL
SWITCH
............................8H-7
TEST, THROTTLE POSITION SENSOR
......8D-18
TEST, THROTTLE POSITION SENSOR
(TPS)
..............................14-45
TEST, TIME LAG
......................21-169TEST, TORQUE CONVERTER CLUTCH
RELAY.............................14-45
TEST, TORQUE CONVERTER STALL.......21-169
TEST, VACUUM SUPPLY.................8H-7
TEST, VEHICLE SPEED SENSOR......8H-5,14-45
TESTING, AUTOMATIC SHUTDOWN
(ASD) RELAY........................14-43
TESTING COOLING SYSTEM FOR LEAKS.....7-18
TESTING, FUEL PUMP RELAY............14-44
TESTING GENERAL INFORMATION,
BATTERY............................8A-3
TESTING, IGNITION SWITCH.............8D-30
TESTING, POWER MIRROR SWITCH........8T-2
TESTING, REAR WIPER/WASHER
SWITCH.......................8K-7,8K-14
TESTING, SWITCH; POWER SEATS.........8R-2
TESTING, SWITCH; POWER WINDOWS......8S-5
TESTING, SWITCH; REAR WINDOW
DEFOGGER..........................8N-2
TESTING, TRANSMISSION COOLER FLOW . . 21-106
TESTING, WIPER SWITCH...............8K-19
TESTS - (VOLTAGE DROP METHOD),
STARTER FEED CIRCUIT................8A-9
TESTS, ANTENNA.......................8F-9
TESTS AT POWERTRAIN CONTROL
MODULE, ELECTRICAL.................8H-6
TESTS AT SERVO, ELECTRICAL............8H-5
TESTS, COMPRESSOR VALVE PLATEÐ
LEAK...............................24-8
TESTS, IGNITION SWITCH CONTINUITY....8D-31
TESTS, OXYGEN SENSOR...............8D-19
TESTS, STARTER CONTROL CIRCUIT......8A-11
TESTS, VEHICLE SPEED CONTROL
SYSTEM............................8H-5
TESTS, WATER PUMP....................7-9
THERMOMETER AND SENSOR SYSTEM
REPAIR PROCEDURES.................8C-6
THERMOSTAT..........................7-13
THERMOSTAT, TEMPERATURE CONTROL . . . 24-35
THICKNESS, AW-4 CLUTCH DISC AND
PLATE ............................21-325
THICKNESS, DISC BRAKE ROTOR..........5-31
THICKNESS VARIATION, DISC BRAKE
ROTOR.............................5-31
THIRD GEAR (CONVERTER CLUTCH
ENGAGED), HYDRAULIC FLOW IN.......21-90
THIRD GEAR, HYDRAULIC FLOW IN D
RANGE.............................21-89
THREAD NOTATIONÐSAE AND METRIC . . INTRO.-9
THREADS, REPAIR DAMAGED OR WORN.....9-4
THROTTLE 3-2 DOWNSHIFT, HYDRAULIC
FLOW DURING FULL..................21-92
THROTTLE 3-2 DOWNSHIFT, HYDRAULIC
FLOW DURING PART..................21-91
THROTTLE BODY; FUEL SYSTEM.....14-29,14-59
THROTTLE CABLE.....................14-16
THROTTLE CABLE, ACCELERATOR PEDAL . . 14-16,
14-54
THROTTLE CABLE ADJUSTMENT,
TRANSMISSION.....................21-185
THROTTLE CABLE ADJUSTMENT,
TRANSMISSION......................21-98
THROTTLE CABLE REPLACEMENT,
TRANSMISSION.....................21-184
THROTTLE POSITION SENSOR............8D-6
THROTTLE POSITION SENSOR TEST.......8D-18
THROTTLE POSITION SENSOR (TPS);
FUEL SYSTEM.......................14-59
THROTTLE POSITION SENSOR (TPS);
IGNITION SYSTEMS..................8D-29
THROTTLE POSITION SENSOR (TPS)
SERVICE..........................21-184
THROTTLE POSITION SENSOR (TPS)
TEST..............................14-45
THROTTLE POSITION SENSOR (TPS)Ð
PCM INPUT.........................14-23
THROTTLE VALVE CABLE ADJUSTMENT,
TRANSMISSION......................21-70
TIE ROD ........................19-14,19-17
TIGHTENING, WHEEL NUT............5-32,5-37
TILT STEERING COLUMN................19-59
TIME LAG TEST
......................21-169
TIMING CASE COVER
................9-27,9-67
TIMING CASE COVER OIL SEAL
REPLACEMENT
...................9-26,9-67
TIMING CHAIN AND SPROCKETS
......9-28,9-68TIMING, IGNITION.....................8D-14
TIMING, VALVE.....................9-26,9-66
TIPS, TRANSMISSION ASSEMBLY........21-146
TIRE AND WHEEL BALANCE..............22-6
TIRE AND WHEEL RUNOUT...............22-8
TIRE CARRIER, EXTERNAL SPARE/WHEEL . 23-172
TIRE INFLATION PRESSURE LABEL.....INTRO.-3
TIRE INFLATION PRESSURES.............22-2
TIRE NOISE OR VIBRATION...............22-4
TIRE WEAR PATTERNS..................22-4
TIRES; LUBRICATION AND MAINTENANCE....0-34
TIRES................................22-1
TIRES, CLEANING OF....................22-2
TIRES, REPLACEMENT...................22-2
TIRE/WHEEL HOLDDOWN AND FLOOR
BRACKETS.........................23-128
TOOL, DRB SCAN; COOLING SYSTEM........7-5
TOOL, DRB SCAN; EMISSION CONTROL
SYSTEMS...........................25-2
TOOL, DRB SCAN; FUEL SYSTEM.........14-51
TOOL, DRB SCAN; IGNITION SYSTEMS.....8D-10
TOP REPAIR, HARD...................23-165
TOP ROOF VENT......................23-165
TOP SERVICE............23-164,23-166,23-167
TORQUE; COOLING SYSTEM..............7-39
TORQUE; FUEL SYSTEM................14-62
TORQUE; IGNITION SYSTEMS............8D-33
TORQUE, COLLISION DAMAGE............13-1
TORQUE CONVERSION..............INTRO.-10
TORQUE CONVERTER; TRANSMISSION
AND TRANSFER CASE...........21-66,21-158
TORQUE CONVERTER CLUTCH RELAY......14-60
TORQUE CONVERTER CLUTCH RELAY
TEST..............................14-45
TORQUE CONVERTER CLUTCH RELAYÐ
PCM OUTPUT.......................14-27
TORQUE CONVERTER INSTALLATION,
TRANSMISSION.....................21-190
TORQUE CONVERTER REMOVAL,
TRANSMISSION.....................21-189
TORQUE CONVERTER STALL TEST.......21-169
TORQUE CONVERTER STATOR CLUTCH
INSPECTION.......................21-189
TORQUE SPECIFICATIONS, 30RH/32RH....21-323
TORQUE SPECIFICATIONSÐ AX 15
MANUAL TRANSMISSION.............21-320
TORQUE SPECIFICATIONSÐACCESSORIES . 23-208
TORQUE SPECIFICATIONS, AW-4
.........21-331
TORQUE SPECIFICATIONS, BATTERY
.......8B-10
TORQUE SPECIFICATIONS; BATTERY/
STARTER/GENERATOR SERVICE
.........8B-12
TORQUE SPECIFICATIONS, BRAKE
..........5-67
TORQUE SPECIFICATIONS; CLUTCH
........6-17
TORQUE SPECIFICATIONS; ELECTRICAL
.....8A-8
TORQUE SPECIFICATIONS; ENGINES
....9-49,9-89
TORQUE SPECIFICATIONS; EXHAUST
SYSTEM AND INTAKE MANIFOLD
........11-10
TORQUE SPECIFICATIONS; FRONT
SUSPENSION AND AXLE
................2-47
TORQUE SPECIFICATIONS; HEATING AND
AIR CONDITIONING
...................24-45
TORQUE SPECIFICATIONS; HORNS
.........8G-3
TORQUE SPECIFICATIONS;
INTRODUCTION
...................INTRO.-8
TORQUE SPECIFICATIONS, NP231/NP242
. . 21-331
TORQUE SPECIFICATIONS; PROPELLER
SHAFTS
............................16-14
TORQUE SPECIFICATIONS; REAR
SUSPENSION AND AXLES
...............3-50
TORQUE SPECIFICATIONS, STARTER
MOTOR
............................8B-11
TORQUE SPECIFICATIONS; STEERING
......19-73
TORQUE SPECIFICATIONS XJ
.............8K-7
TORQUE SPECIFICATIONSÐXJ VEHICLES
. . 23-207
TORQUE VALUES, STANDARD
.........INTRO.-9
TOW HOOKÐXJ VEHICLES, REAR
.........23-87
TOW HOOKS
..........................13-14
TOW HOOKS, FRONT
....................13-5
TOWING, JUMP STARTING, HOISTING
.......0-7
TOWING RECOMMENDATIONS
..............0-8
TRACK BAR
....................2-10,2-13,3-6
TRACKS, BUCKET SEAT PLATFORM
.......23-105
TRAC-LOK DIFFERENTIAL
................3-44
JINDEX23
Description Group-Page Description Group-Page Description Group-Page