1993 DODGE TRUCK alternator belt

8A
- 10
ELECTRICAL
•
STARTING SYSTEM DIAGNOSIS

TEST CONDITIONS • PLACE GEAR SELECTOR
IN
PARK OR NEUTRAL AND SET PARK BRAKE
OR
EQUIVALENT. • VERIFY BATTERY STATE-OF-CHARGE AND CRANKING CAPACITY, SEE BATTERY SECTION.
• CLEAN BATTERY TOP, POSTS, AND TERMINALS.
• VERIFY ALTERNATOR DRIVE BELT TENSION.
• DISCONNECT AND GROUND COIL CABLE. SYMPTOM
SYMPTOM SYMPTOM SYMPTOM SYMPTOM
STARTER FAILS TO STARTER FAILS TO STARTER ENGAGES, STARTER ENGAGES STARTER DOES NOT

ENGAGE.
NO SOUNDS
ENGAGE
SOLENOID FAILS TO TURN DRIVE CLUTCH

DISENGAGE
AFTER
OR RELAY CLICKS ENGINE. DOME
LIGHT
SPINS
OUT
ENGINE STARTS

DIMS

POSSIBLE
CAUSE
POSSIBLE
CAUSE
POSSIBLE
CAUSE
POSSIBLE
CAUSE
POSSIBLE
CAUSE
STARTER CONTROL
RESISTANCE
TOO
RESISTANCE
TOO DRIVE CLUTCH
FAULTY

IGNITION
SWITCH
CIRCUIT
FAULTY
HIGH
IN
STARTER
HIGH
IN
STARTER

FAULTY

FEED CIRCUIT FEED CIRCUIT

BROKEN
TEETH

IGNITION
SWITCH ON RING GEAR
STARTER RELAY

FAULTY
STARTER CONTROL STARTER ASSEMBLY

FAULTY

CIRCUIT
FAULTY FAULTY

STARTER ASSEMBLY
PARK/NEUTRAL
FAULTY

STARTER ASSEMBLY
POSITION STARTER SOLENOID ENGINE

FAULTY

SWITCH
FAULTY

SEIZED

(AUTO
TRANS.) STARTER

FAULTY
OR STARTER
MISADJUSTED STARTER ASSEMBLY IMPROPERLY

FAULTY
MOUNTED
STARTER RELAY
REFER
TO

FAULTY
APPROPRIATE GROUP
AND SECTION OF THIS
MANUAL FOR PROPER
STARTER ASSEMBLY
SERVICE
AND TEST

FAULTY
PROCEDURES
FOR THE
COMPONENTS INVOLVED

J938A-9
tery post and the solenoid threaded stud. The follow­
ing operation will require a voltmeter, accurate to 1/10 of a volt.
Before performing the tests, assure the following
procedures are accomplished:
•
Disconnect the distributor connector (gas engine).

•
Disconnect both wires on the fuel solenoid (diesel engine) (Fig. 3). Verify that:

•
all lights and accessories are OFF

•
transmission shift selector is in PARK (automatic)
or NEUTRAL (manual)

•
parking brake is applied

•
battery is fully charged (refer to Battery Test Pro­
cedures). (1) Connect positive lead of voltmeter to battery
negative post. Connect negative lead of voltmeter to
battery negative cable clamp (Fig. 4). Rotate and
Fig.
3
Diesel
Engine
Fuel
Solenoid

9 - 16
ENGINES

•
CONDITION

POSSIBLE
CAUSES
CORRECTION

EXCESSIVE
VIBRATION
Loose
or broken engine mounts.
Replace
engine mounts.

Damaged
fan or improperly
operating
accessories.
Check
and replace the vibrating components.
Improperly operating vibration
clamper. Inspect/replace the vibration damper.
Improperly operating fan hub. Inspect/replace the fan hub.

Worn
or
damaged
alternator
bearing.
Check/replace
the alternator.
Flywheel
housing
misaligned. Check/correct flywheel alignment.

Loose
or broken power

component.
Inspect
the crankshaft and rods for damage
that
causes
an

unbalance.
Repair/replace as required.

Worn
or unbalanced driveline
components.
Check/repair driveline components.

EXCESSIVE
ENGINE

NOISES
Drive belt squeal, insufficient

tension
or abnormally high
loading.
Check
the tensioner and inspect the drive belt. Make sure water

pump,
tensioner pulley, fan hub and alternator turn
freely.

Intake air or exhaust leaks. Refer to
Excessive
Exhaust
Smoke
(Engine
Diagnosis—

Performance).

Excessive
valve
lash
Adjust
valves.
Make sure the
push
rods are not bent and rocker
levers or adjusting screws are not severely worn. Replace bent

or
severely worn
pads.

Turbocharger
noise.
Check
turbocharger impeller and turbine wheel for housing
contact. Repair/replace as required.

Gear
train
noise.
Visually
inspect and measure gear
backlash.
Replace gears as
required.

Power
function knock.
Check/replace
rod and main bearings.

ALTERNATOR
NOT

CHARGING
OR IN-
SUFFICIENT
CHARGING
Loose
or corroded battery

connections.

Alternator belt slipping. Clean/tighten battery connection.

Check/replace
belt tensioner. Check/replace belt.
Alternator pulley loose on
shaft.
Tighten pulley.
Improperly operating
alternator.
Check/replace
alternator.
J9109-253
SERVICE DIAGNOSIS (DIESEL ENGINE) - MECHANICAL (CONT.)

5.9L
(DIESEL)
ENGINE
9-153
TORQUE
SPECIFICATIONS

COMPONENT

Air
Fuel
Control
Banjo Screw (In Pump) ....
Air
Fuel
Control
Fitting
(In
Head)

Alternator
Ground Cable Mounting to
Block

Alternator
Mounting to
Water
Pump
Inlet
..

Alternator
Pulley
Alternator
Support
(Upper)

Battery
Cable
(Negative)
Mounting to Block ,

Belt
Tensioner
Mounting
Block
Heater
Mounting

Cab
Heater
Hose
Clamp

Cab
Heater
Tubing
Clamp Mounting.......
Camshaft
Thrust
Plate

Clutch Cover Mounting to
Flywheel
...
Connecting Rod
(Alternately
tighten
in 3 steps) Step 1
Step 2
Step 3 .
Cooling Fan Mounting to
Fan
Clutch

Crossover
Clamp (Air)

Cylinder
Head
Mounting Bolts

1.
All
Bolts....

2.
Long
Bolts
.........

3.
Tighten
All
Bolts
An
Additional

Exhaust
Manifold

Exhaust
Outlet
Pipe
- V
Band
Clamp
Exhaust
Pipe
Clamp Mounting
Exhaust
Pipe
Steady
Rest
Mounting to Trans .

Fan
Clutch Mounting/Fan Hub
(L
Hand
Threads)..
Fan Hub
Bracket
Mounting
Fan Hub Bearing
Retaining
Capscrew
Fan
Pulley
to
Fan
Hub
Fan
Pulley
Crankshaft .
Fan
Shroud
Mounting Nuts

Flywheel
Bolts

Flywheel
Housing
- Adaptor

Front
Engine
Mount Isolator Mounting to Mount..

Front
Engine
Mount Through Bolt

Front
Engine
Mount to Block

Front
Oil
Filler
Pipe
-
Access
Cover

Fuel
Banjo Screw (In
Fuel
Pump)

Fuel
Banjo Screw (In
Head)

Fuel
Banjo Screw (In
Injector)

Fuel
Filter

Fuel
Heater
Assembly
Mounting

Fuel
Heater
Ground Mounting to
Intake
Manifold

Fuel
Link
Fitting
(High Pressure)

Fuel
Low Pressure Supply

Fuel
Pump
Drive
Gear
(With
Pump
Unlocked)

Fuel
Pump Lock (Bosch)
TORQUE

12 N-m 9 ft. lbs.
8 N-m 6 ft. lbs.
24 N-m 18 ft. lbs.
41 N*m 30 ft. lbs.
80 N-m 60 ft. lbs.
24 N-m 18 ft. lbs.
77 N-m 57 ft. lbs.
43 N-m 32 ft. lbs.
12 N-m 9 ft. lbs.
4 N-m (35 in. lbs.)
24 N-m 18 ft. lbs.
24 N-m 18 ft. lbs.
23 N-m 17 ft. lbs.
35 N-m 26 ft. lbs.
70 N-m 51 ft. lbs.
100 N-m 73 ft. lbs.
20 N-m 15 ft. lbs.

5
N-m (44 in. lbs.)
90 N-m 66 ft. lbs.
120 N-m 89 ft. lbs.
90°
43 N-m 32 ft. lbs.
8 N-m (72 in. lbs.)
27 N-m 20 ft. lbs.
68 N-m 50 ft. lbs.
57 N-m 42 ft. lbs.
24 N-m 18 ft. lbs.
77 N-m 57 ft. lbs.
9 N-m 7 ft. lbs.
9 N-m 7 ft. lbs.
11 N-m (95 in. lbs.)
137 N-m 101 ft. lbs.
60 N-m 44 ft. lbs.
109 N-m 80 ft. lbs.
41 N-m 30 ft. lbs.
60 N-m 44 ft. lbs.
Hand
Tighten

32 N-m 24 ft. lbs.
24 N-m 18 ft. lbs.
8 N-m 6 ft. lbs.
Vi
Turn
after
contact

32 N-m 24 ft. lbs.
12 N-m 9 ft. lbs.
24 N-m 18 ft. lbs.
24 N-m 18 ft. lbs.
65 N-m 48 ft. lbs.
30 N-m 22 ft. lbs.
J9109-261